Heath Zenith SL-2747-02 User manual

P.O. Box 90045

Bowling Green, KY 42102-9045

Hardwired

Mechanical

Chime

-2-

598-1112-06

CHIME REPLACEMENT INSTALLATION

Note: Electrical work must be in accordance with national and local

electrical codes. If in doubt, consult a qualiﬁed electrician.

1. Verify transformer power rating. Power must be supplied from

a 16 Volt AC, 10 Watt or a 16 Volt AC, 15 Watt transformer

(Heath

®

/Zenith models 122C, 121AC, or 125C).

2. Remove cover from existing chime.

3. Label all wires before disconnecting. Using masking tape, mark

each wire according to existing chime terminal markings.

• “F”–FrontPushButtonWire

• “T”–TransformerWire

• “R”–RearPushButtonWire*

4. Disconnect all wires from existing chime.

5. Remove existing chime base from wall.

6. Determine proper chime base orientation. The chime cover

style may determine orientation.

7. Determinecovermountingtype.Forhangpinandholetype

covers, hang pin should be installed before mounting base to

wall. Install hang pin by snapping into mounting hole or sliding

ontochimebase,dependingontypeofhangpin(seeFigures1

and 3).

Illustrations may vary from actual chime unit.

Figure 1 - Mechanical Chime Identiﬁcation

(Model 35 Base Shown)

FRONT

REAR

TRANS

Hang Pin, Snap-On

Type (Used for Hang

Pin and Hole Covers)

Base Orientation

Marking

Wire Entrance Hole

Mounting Slot (x4)

Tone Bars

Transformer and

Push Button Wire

Connections

Continued

Plungers

Hang Pin Mounting

Slot (Horizontal)

Hang Pin Mounting

Slot (Vertical)

Hang Pin, Slide-On Type

(Used for Hang Pin and

Hole Covers)

-3-

598-1112-06

FRONT

REAR

TRANS

R

T

F

8. Route wires through wire entrance hole in new chime base.

9. Mount chime base to wall using screws provided.

10. Connectwire“F”toscrewterminalmarked“FRONT”.Connect

wire“T”toscrewterminalmarked“TRANS”.Connectwire

“R”toscrewterminalmarked“REAR”*(SeeFigure2).

11. Install chime cover (see page 4).

*Note:Someinstallationsmaynotincludereardoorpushbutton.

Figure 2 - Mechanical Chime Wiring

(Model 35 Base Shown)

Existing Chime Wires

Wall

Replacement Chime Base

Rear Door Push Button

(if Applicable)

-4-

598-1112-06

FRONT

REAR

TRANS

Figure 4 - Mounting Snap-On Cover

INSTALL CHIME COVER

Place chime cover securely over base.

• For hang pin and hole covers: Attach hang pin to base prior

to mounting base on wall. Line up hole in cover with pin and hang

(seeFigure3).

• For snap-on covers: Apply pressure to the cover until it snaps

intoplace(seeFigure4).Firmlygraspcoverandpulltoremove

from base.

• For hang bracket covers: Determine if the cover will hang

vertically or horizontally on the base. Place bracket into the cor-

rect slot inside chime cover.

Adjust bracket (if necessary) so that bracket is ﬂush with back

surfaceofcover.Slidebracketintoslotonbasetohangcover(see

Figure5).

Note:Neverusecleanersorpolishes.Neveruseanyuidsonthe

chime mechanism. Use dry cloth to clean chime cover and base.

FRONT

REAR

TRANS

Figure 3 - Pin for Hanging Cover

Hang Pin,

Snap-On Type

Illustrations may

vary from actual

chime unit.

Snap-On Cover

Base Orientation

Marking

Hang Pin, Slide-On Type

-5-

598-1112-06

FRONT

UP

TRANS

Figure 5 - Mounting Hang Bracket Cover

Illustrations may vary from actual chime unit.

Hang Bracket

Cover

Base

Orientation

Marking

Hang Bracket

Chime Base

(Mounted Vertically)

Hang

Bracket Slot

-6-

598-1112-06

TROUBLESHOOTING

Chime does not sound:

• Check Chime:Disconnectwirefromterminalmarked“TRANS”.Havesomeoneoperatepushbuttonatfrontdoorwhileyoumo-

mentarilytouchthe“TRANS”wiretoterminalmarked“FRONT”.Youwillseeasmallsparkifpushbutton,wiring,andtransformer

areoperatingproperly.Repeatthestepsfor“REAR”terminalandrearpushbutton.Ifwiringbetweentransformerandpushbutton(s)

check out properly, replace chime.

• Check Transformer:Testtransformervoltageoutputwithavoltmeter.Ifavoltmeterisnotavailable,momentarilytouchthetwo

low-voltage terminals with a screwdriver. You will see a small spark if transformer is operating properly. If no spark is evident, replace

transformer.

• Check Push Button(s): Remove suspected push button from door frame, disconnect wire from terminals and touch bare wires

together. If chime operates, push button is defective. Replace push button.

-7-

598-1112-06

ONE YEAR LIMITED WARRANTY

This is a “Limited Warranty” which gives you speciﬁc legal rights. You may also have other rights which vary from state to state or province to province.

For a period of one year from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge to you.

Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs, batteries, and other expendable items are not

covered by this warranty. Unauthorized service or modiﬁcation of the product or of any furnished component will void this warranty in its entirety. This war-

ranty does not include reimbursement for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges.

This warranty covers only HeathCo LLC assembled products and is not extended to other equipment and components that a customer uses in conjunction

with our products.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION

OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN

LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF HEATHCO

LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS

OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of incidental or consequential dam-

ages, so the above limitation or exclusion may not apply to you.

Please keep your dated sales receipt, it is required for all warranty requests.

HeathCo LLC reserves the right to discontinue and to change speciﬁcations at any time without notice without incurring any obligation to incorporate new features in

previously sold products.

TECHNICAL SERVICE

Please call 1-800-858-8501 (English speaking only) for assistance before returning product to store.

If you experience a problem, follow this guide. You may also want to visit our Web site at: www.hzsupport.com. If the problem per-

sists,call*forassistanceat1-800-858-8501,7:30AMto4:30PMCST(M-F).Youmayalsowrite*to:

HeathCo LLC

P.O. Box 90045, Bowling Green, KY 42102-9045

ATTN:TechnicalService

*IfcontactingTechnicalService,pleasehavethefollowinginformationavailable:ModelNumber,DateofPurchase,andPlaceofPur-

chase.

No Service Parts Available for this Product

-8-

598-1112-06

R

T

F

FRONT

REAR

TRANS

Chime System Wiring Diagram

Transformer

Front Door

Push Button

Chime

Rear Door

Push Button

(If Applicable)

Page is loading ...

-13-

598-1112-06

FRONT

UP

TRANS

Figura 5 - Montaje de la tapa tipo soporte de colgar

Tapa tipo

soporte de

colgar

Soporte para colgar

Base de la campana

(montada verticalmente)

Ranura para

el soporte

de colgar

Las ilustraciones pueden variar de la unidad de campana real.

Marca de

orientación

de la base

Page is loading ...

-16-

598-1112-06

R

T

F

FRONT

REAR

TRANS

Esquema eléctrico del sistema de la campana

Transformador

Pulsador de la

puerta frontal

Campana

Pulsador de la

puerta posterior

(si se usa)

Page is loading ...

-24-

598-1112-06

R

T

F

FRONT

REAR

TRANS

Diagramme de câblage du carillon

Transformateur

Bouton-poussoir de

l’entrée principale

Carillon

Bouton-poussoir de

l’entrée secondaire

(s’il y a lieu)

Heath Zenith SL-2747-02 User manual

This manual is also suitable for

Heath Zenith SL-2747-02 User manual

in other languages

Related papers

Other documents