Texas Instruments TMP108EVM Users User guide

Brand: Texas Instruments

Model: TMP108EVM Users

Type: User guide

This manual is also suitable for

TMP108EVM

Texas Instruments TMP108EVM Users

Below you will find brief product information for Texas Instruments TMP108EVM Users:

TMP108EVM is used for reading temperatures between –40°C and +125°C with 12 bits of resolution.
TMP108EVM is ideal for extended temperature measurement and thermal management optimization in various applications.
TMP108EVM uses a two-wire I2C™ and SMBus™ interface that allows up to four devices on one bus.
TMP108EVM comes with the following contents upon purchase: TMP108EVM PCB Test Board (1), SM-USB-DIG Platform PCB (1), USB Extender Cable (1), 10-pin Connector Ribbon Cable (1), User’s Guide CD-ROM (1)

Texas Instruments TMP108EVM Users

Below you will find brief product information for Texas Instruments TMP108EVM Users:

TMP108EVM is used for reading temperatures between –40°C and +125°C with 12 bits of resolution.
TMP108EVM is ideal for extended temperature measurement and thermal management optimization in various applications.
TMP108EVM uses a two-wire I2C™ and SMBus™ interface that allows up to four devices on one bus.
TMP108EVM comes with the following contents upon purchase: TMP108EVM PCB Test Board (1), SM-USB-DIG Platform PCB (1), USB Extender Cable (1), 10-pin Connector Ribbon Cable (1), User’s Guide CD-ROM (1)

User's Guide

SBOU129–April 2013

TMP108EVM Evaluation Board and Software Tutorial

This user's guide describes the characteristics, operation, and use of the TMP108EVM evaluation board. It

discusses how to set up and configure the software and hardware and reviews various aspects of the

program operation. Throughout this document, the terms evaluation board, evaluation module, and EVM

are synonymous with the TMP108EVM. This user's guide also includes information regarding operating

procedures and input/output connections, an electrical schematic, printed circuit board (PCB) layout

drawings, and a parts list for the EVM.

Contents

1 Overview ..................................................................................................................... 2

2 Hardware Configuration .................................................................................................... 3

3 Hardware Installation ....................................................................................................... 5

4 Software Installation ........................................................................................................ 7

5 Software Operation ......................................................................................................... 9

6 Documentation ............................................................................................................. 14

List of Figures

1 Hardware Included with TMP108EVM Kit ............................................................................... 2

2 Hardware Configuration.................................................................................................... 3

3 TMP108EVM Board Block Diagram...................................................................................... 3

4 SM-USB-DIG Platform Block Diagram................................................................................... 4

5 Connecting SM-USB-DIG Platform....................................................................................... 5

6 Confirmation of SM-USB-DIG Platform Driver Installation............................................................. 5

7 10-Pin Ribbon Cable Extender............................................................................................ 6

8 Starting the Software Installation ......................................................................................... 7

9 License Agreements........................................................................................................ 8

10 Software Interface........................................................................................................... 9

11 Communication Error with the SM-USB-DIG Platform................................................................. 9

12 Read Continuously ........................................................................................................ 10

13 Configuration Register .................................................................................................... 11

14 Reading the Temperature Gauge ....................................................................................... 12

15 TLow Register.............................................................................................................. 13

16 THigh Register............................................................................................................. 13

17 PCB Layout................................................................................................................. 14

18 Board Schematic .......................................................................................................... 15

SMBus is a trademark of Intel Corporation.

Windows, Windows XP are registered trademarks of Microsoft Corporation.

C is a trademark of NXP Semiconductors.

All other trademarks are the property of their respective owners.

SBOU129–April 2013 TMP108EVM Evaluation Board and Software Tutorial

Submit Documentation Feedback

Overview

www.ti.com

1 Overview

The TMP108 is a digital output temperature sensor capable of reading temperatures of –40°C to +125°C

with 12 bits of resolution. The TMP108 uses a two-wire I

C™ and SMBus™ interface that allows up to four

devices on one bus. The TMP108 is ideal for extended temperature measurement, and is specified to

operate between –40°C and +125°C. It is also ideal for thermal management optimization in a variety of

consumer, computer, and environmental applications.

This document gives a general overview of the TMP108EVM and provides a general description of the

features and functions to be considered while using this evaluation module.

1.1 TMP108EVM Kit Contents

Table 1 summarizes the contents of the TMP108EVM kit. Figure 1 shows all of the included hardware.

Contact the Texas Instruments Product Information Center if any component is missing. It is highly

recommended that you also check the TMP108 product folder on the TI web site at www.ti.com to verify

that you have the latest versions of the related software.

Table 1. TMP108EVM Kit Contents

Item Quantity

TMP108EVM PCB Test Board 1

SM-USB-DIG Platform PCB 1

USB Extender Cable 1

10-pin Connector Ribbon Cable 1

User’s Guide CD-ROM 1

Figure 1. Hardware Included with TMP108EVM Kit

1.2 Related Documentation from Texas Instruments

The following documents provide information regarding Texas Instruments' integrated circuits used in the

assembly of the TMP108EVM. This user's guide is available from the TI web site under literature number

SBOU128. Any letter appended to the literature number corresponds to the document revision that is

current at the time of the writing of this document. Newer revisions may be available from the TI web site,

or call the Texas Instruments' Literature Response Center at (800) 477-8924 or the Product Information

Center at (972) 644-5580. When ordering, identify the document by both title and literature number.

Table 2. Related Documentation

Document Literature Number

TMP108 Product Data Sheet SBOS663

SM-USB-DIG Platform User Guide SBOU098

TMP108EVM Evaluation Board and Software Tutorial SBOU129–April 2013

Submit Documentation Feedback

Test Point

Headers

TP1 to

TP4

10-Pin

SM-DIG

Connector

I C Interface

TMP108

Computer

SM-USB-DIG

TMP108EVM

www.ti.com

Hardware Configuration

2 Hardware Configuration

Figure 2 shows the overall system configuration for the TMP108EVM. The computer runs the software

that communicates with the SM-USB-DIG Platform. The SM-USB-DIG Platform generates the digital

signals used to communicate with the TMP108 test board. The SM-USB-DIG and TMP108EVM are easily

connected through 10-pin board-to-board connectors on the SM-USB-DIG Platform and the TMP108EVM

PCBs. After these two boards are connected, simply plug the assembly into the computer USB port.

Figure 2. Hardware Configuration

2.1 Theory of Operation for TMP108 Hardware

The TMP108EVM only requires the two-wire I

C lines (SDA and SCLK) and V

DUT

/GND, as shown in

Figure 3. The TMP108EVM has test points to monitor these signals. If desired, use these test points as

external signal inputs. These test points may also be used for external input/output signals.

Figure 3. TMP108EVM Board Block Diagram

2.2 Signal Definitions of H1 (10-Pin Male Connector Socket)

Table 3 shows the pinout for the 10-pin connector socket used to communicate between the TMP108EVM

and the SM-USB-DIG. Only the I

C communication lines (pins 1 and 3) and the V

DUT

and GND (pins 6 and

8, respectively) are used on the TMP108EVM.

Table 3. Signal Definition of H1 on TMP108EVM Board

Pin on U1 Signal Description

1 I2C_SCL I

C clock signal (SCL)

2 CTRL/MEAS4 GPIO: control output or measure input

3 I2C_SDA1 I

C data signal (SDA)

4 CTRL/MEAS5 GPIO: control output or measure input

5 SPI_DOUT1 SPI data output (MOSI)

Switchable DUT power supply: +3.3 V, +5 V, Hi-Z

6 V

DUT

(disconnected)

(1)

7 SPI_CLK SPI clock signal (SCLK)

8 GND Power return (GND)

9 SPI_CS1 SPI chip select signal (CS)

10 SPI_DIN1 SPI data input (MISO)

(1)

When V

DUT

is Hi-Z, all digital I/O are Hi-Z as well.

SBOU129–April 2013 TMP108EVM Evaluation Board and Software Tutorial

Submit Documentation Feedback

TUSB3210

8052 Cm

with USB Interface

and UART

8Kx8-byte

EEPROM

+3.3V

USB

+5V

Power-On Reset

SM USB DIG Platform

To Test Board

To Computer and Power Supplies

Power

Switching

Switched

Power

USB Bus

from

Computer

USB Power

+5.0V

+3.0V

(H-Z, 3.3V, or 5V)

DUT

Buffers and

Level Translators

I C/SPI

Control and

Measure Bits

+3.3V

Regulator

Hardware Configuration

www.ti.com

2.2.1 Theory of Operation for SM-USB-DIG Platform

Figure 4 shows the block diagram for the SM-USB-DIG Platform. This platform is a general-purpose data

acquisition system that is used on several different Texas Instruments evaluation modules. The details of

its operation are included in a separate document, SBOU098 (available for download at www.ti.com). The

block diagram shown in Figure 4 gives a brief overview of the platform. The primary control device on the

SM-USB-DIG Platform is the TUSB3210.

Figure 4. SM-USB-DIG Platform Block Diagram

TMP108EVM Evaluation Board and Software Tutorial SBOU129–April 2013

Submit Documentation Feedback

www.ti.com

Hardware Installation

3 Hardware Installation

The TMP108EVM hardware installation involves connecting the two PCBs of the EVM together,

connecting the USB cable, applying power, and setting the jumpers. This section presents the details of

this procedure.

3.1 Electrostatic Discharge Warning

CAUTION

Many of the components on the TMP108EVM are susceptible to damage by

electrostatic discharge (ESD). Customers are advised to observe proper ESD

handling precautions when unpacking and handling the EVM, including the use

of a grounded wrist strap at an approved ESD workstation.

3.2 Typical Hardware Connections

To connect the TMP108 test board and the SM-USB-DIG Platform together, gently slide the male and

female ends of the 10-pin connectors together. Make sure that the two connectors are completely pushed

together; loose connections can cause intermittent operation. Then use the USB extension cable to

connect everything to the computer, as shown in Figure 5.

Figure 5. Connecting SM-USB-DIG Platform

3.3 Connecting the USB Cable to the SM-USB-DIG Platform

When the SM-USB-DIG Platform is first connected, the computer typically responds with a Found New

Hardware, USB Device popup message. The message then changes to Found New Hardware, USB

Human Interface Device. This prompt indicates that the device is ready to use. Note that the SM-USB-DIG

Platform uses the human interface device drivers that are part of the Microsoft Windows

operating

systems.

In some cases, the Add Hardware Wizard appears. If this prompt pops up, allow the system device

manager to install the human interface drivers by clicking Yes when requested to install drivers. Windows

confirms installation of the drivers with the message shown in Figure 6.

Figure 6. Confirmation of SM-USB-DIG Platform Driver Installation

SBOU129–April 2013 TMP108EVM Evaluation Board and Software Tutorial

Submit Documentation Feedback

Hardware Installation

www.ti.com

3.4 Hardware Features

This section describes some of the hardware features present on the TMP108EVM test board.

3.4.1 I

C Translator and Test Points

The TMP108EVM is equipped with an onboard I

C level translator. This allows the TMP108 to be

operated at 3.3 V or 1.8 V by changing the jumper position on J2. The I

C test points SDAB and SCLB are

connected to the I

C line of the SM-USB-DIG Platform and run to the input of the level translator, U2. The

C test points, SDAA and SCLA, are connected to the output of the level translator, U2, and run to the

clock and data lines of the TMP108.

3.4.2 DIP Adapter Socket, J5

The TMP108EVM provides the option of connecting a second temperature sensor though a DIP adapter

socket. The A0 pin on the second temperature sensor is connected to GND. In order to avoid conflicts,

make sure that jumper J4 on the first temperature sensor is not set to GND. The socket is not included on

the EVM and must be ordered separately. The part number is specified in Table 4, the bill of materials. If

using this socket, visit the DIP-Adapter-EVM web page (http://www.ti.com/tool/dip-adapter-evm) for SOIC-

to-DIP adapter boards.

3.4.3 10-Pin Connector Ribbon Extender (Optional)

The TMP108EVM kit ships with an optional ribbon cable for extending the connection between the SM-

USB-DIG Platform and the PCB. This extension cable is useful if high temperature tests must be run on

the test board because the SM-USB-DIG Platform is not rated for high temperatures. To connect the

ribbon cable, attach the cable to the EVM and SM-USB-DIG, as shown in Figure 7.

Figure 7. 10-Pin Ribbon Cable Extender

TMP108EVM Evaluation Board and Software Tutorial SBOU129–April 2013

Submit Documentation Feedback

www.ti.com

Software Installation

4 Software Installation

This section discusses how to install the TMP108EVM software.

4.1 Operating System Requirements

The TMP108EVM software has been tested on Microsoft Windows XP

operating systems (OS) with

United States and European regional settings. The software should also function on other Windows

operating systems.

4.2 Installing the Software

The TMP108EVM software is included on the CD that is shipped with the EVM kit. It is also available

through the TMP108EVM product folder on the TI website. To install the software to a computer, insert the

disc into an available CD-ROM drive. Navigate to the drive contents and open the TMP108EVM software

folder. Locate the compressed file (TMP108EVM.zip) and extract the TMP108EVM files into a specific

TMP108EVM folder (for example, C:\TMP108EVM) on your hard drive.

Once the files are extracted, navigate to the TMP108EVM folder you created on the hard drive. Locate the

setup.exe file and execute it to start the installation. The TMP108 software installer file then begins the

installation process as shown in Figure 8.

Figure 8. Starting the Software Installation

SBOU129–April 2013 TMP108EVM Evaluation Board and Software Tutorial

Submit Documentation Feedback

Software Installation

www.ti.com

After the installation process initializes, select the directory in which to install the program; the default

location is C:\Program Files\TMP108\ and C:\Program Files\National Instruments\. Following this option,

two license agreements are presented that must be accepted, as shown in Figure 9. After accepting the

Texas Instruments and National Instruments license agreements, the progress bar opens and shows the

installation of the software. After the installation process is completed, click Finish.

Figure 9. License Agreements

TMP108EVM Evaluation Board and Software Tutorial SBOU129–April 2013

Submit Documentation Feedback

www.ti.com

Software Operation

5 Software Operation

This section discusses how to use the TMP108EVM software.

5.1 Starting the Software

To start the TMP108 software, go to the Windows Start menu, select All Programs, and then select the

TMP108EVM program.

Figure 10 illustrates how the software appears if the TMP108EVM is functioning properly.

Figure 10. Software Interface

Figure 11 shows the error that pops up if the computer cannot communicate with the EVM. In the event

you receive this error, first ensure that the USB cable is properly connected on both ends. Another

possible source for this error is a problem with your computer USB human interface device driver. Make

sure that the device is recognized when the USB cable is plugged in, indicated by a Windows-generated

confirmation sound.

Figure 11. Communication Error with the SM-USB-DIG Platform

SBOU129–April 2013 TMP108EVM Evaluation Board and Software Tutorial

Submit Documentation Feedback

Software Operation

www.ti.com

5.2 Using the Software

5.2.1 Reading from Registers

When first starting the TMP108EVM software, confirm there are stable connections to the test board by

toggling the Read Continuously button, as shown in Figure 12. If all devices are communicating correctly,

the temperature is seen to change over time in the TMP108 Local Temperature box. If communication

with the deivce cannot be established, select the Device Addressing Tab to verify the correct device

address.

Figure 12. Read Continuously

TMP108EVM Evaluation Board and Software Tutorial SBOU129–April 2013

Submit Documentation Feedback

www.ti.com

Software Operation

5.2.2 Configuration Register

The TMP108EVM software contains a tab for the configuration register. Changing values in this register

automatically writes them. Bits CR1 and CR0 set the conversion rate of the TMP108. Bits FH and FL

denote if the temperature has exceeded the limits set by the THigh and TLow registers. Bit TM indicates

to the device whether to operate in comparator mode or interrupt mode. Bits M1 and M0 enable different

measurement modes including One-Shot Temperature Measurement mode and Continuous Conversion

mode. Bit POL adjusts the polarity of the ALERT pin output. Bits HYS1 and HYS0 configure the hysteresis

for the limit comparison of the TMP108 when operating in Comparator mode. See the TMP108 data sheet

(SBOS663) for more information. Figure 13shows the Configuration Register tab in the TMP108EVM

software.

Figure 13. Configuration Register

SBOU129–April 2013 TMP108EVM Evaluation Board and Software Tutorial

Submit Documentation Feedback

Software Operation

www.ti.com

5.2.3 Reading the Temperature Gauge

The Local Temperature box on the TMP108EVM software displays the measured values of the TMP108

registers in a graphical format, as shown in Figure 14 . This value is displayed in degrees Celsius. A

continuous reading can be displayed by toggling the Read Continuously button.

Figure 14. Reading the Temperature Gauge

5.2.4 Alert Configuration (Tlow and Thigh)

The TLow Register tab and the THigh Register tab set the limits of the TLow and THigh register, as shown

in Figure 15 and Figure 16, respectively. This setting is made by entering the temperature in the Write

TLow Limit or Write THigh Limit field. Confirm the limit by clicking the Read TLow Register or Read THigh

D2 to turn off and D3 to turn on. Note that if the POL bit in the Configuration Register is high, D3 is always

on because the comparator looks for the ALERT pin to be active low. To reset the alert pin after it has

been triggered, read the Configuration Register again.

TMP108EVM Evaluation Board and Software Tutorial SBOU129–April 2013

Submit Documentation Feedback

www.ti.com

Software Operation

Figure 15. TLow Register

Figure 16. THigh Register

SBOU129–April 2013 TMP108EVM Evaluation Board and Software Tutorial

Submit Documentation Feedback

Documentation

www.ti.com

6 Documentation

This section contains the component layout, schematic diagram, and bill of materials for the TMP108EVM.

Documentation information for the SM-USB-DIG Platform can be found in SBOU098, the SM-USB-DIG

Platform User’s Guide, available at the TI web site at http://www.ti.com.

6.1 PCB Layout

Figure 17 shows the PCB layout of the TMP108EVM.

NOTE: This image is not to scale; it is intended to show location of important parts and not for manufacturing.

Figure 17. PCB Layout

TMP108EVM Evaluation Board and Software Tutorial SBOU129–April 2013

Submit Documentation Feedback

TMP108EVM

TMP108

V+

ALERT

GND

SCL

SDA

Vcca

SCLA

SDAA

GNDEN

SDAB

SCLB

Vccb

PCA9517DR

GND

OUT

TPS79918

I2C_SCL

I/O 4

I2C_SDA

I/O 5

SPI_MOSI

VDUT

SPI_CLK

GND

SPI_CS

SPI_MISO

ALERT

GND

LED Driver (ALERT)

GND

Power LED

VCC

845

R10

845

R11

0.1µF

GNDGND

GND

0.1µF

GND

10.0k

TMP108 Communications

ALERT

VCC

GND

SDA

SCL

SCL SDA

GND

0.1µF

GND

4 5

SCL

SDA

V+

GND

10.0k

V+

0.1µF

GND

Vcc_1.8

Vcc_3.3

SCLA

SDAA

V+

SCLB

SDAB

ALERT

ALERT 2

GND

2.2µF

GND

www.ti.com

Documentation

6.2 Board Schematic

Figure 18 shows the schematic for the TMP108EVM board.

Figure 18. Board Schematic

SBOU129–April 2013 TMP108EVM Evaluation Board and Software Tutorial

Submit Documentation Feedback

Documentation

www.ti.com

6.3 Bill of Materials

Table 4 lists the bill of materials for the TMP108EVM.

Table 4. Bill of Materials

Digi-Key Manufacturer

Item No. Qty Value Ref Des Description Manufacturer Part Number Part Number

1 5 0.1 µF C1, C3, C4, C6, C7 CAP, CERM, 0.1 µF, 16 V, ±5%, X7R, AVX 478-3726-1-ND 0603YC104JAT2A

0603

2 1 2.2 µF C2 CAP, CERM, 2.2 µF, 6.3 V, ±10%, X5R, Kemet 399-3362-1-ND C0603C225K9PACTU

0603

3 2 Red LED D1,D3 Red LED LTST-C190EKT Lite-On Inc 160-1182-6-ND LTST-C190EKT

4 1 Green LED D2 LTST-C190GKT Lite-On Inc 160-1183-1-ND LTST-C190GKT

5 6 White Test Point ALERT, ALERT 2, Test Point, TH, Multipurpose, White Keystone 5012K-ND 5012

SCLA, SCLB,

SDAA, SDAB

6 3 Black Test Point GND Test Point, TH, Multipurpose, Black Keystone 5011K-ND 5011

7 3 Red Test Point V+, Vcc_1.8, Test Point, TH, Multipurpose, Red Keystone 5010K-ND 5010

Vcc_3.3

8 4 Bumpon H1, H2, H3, H4 Bumpon, Hemisphere, 0.44 × 0.20, Clear 3M SJ5303-7-ND SJ-5303 (CLEAR)

9 1 Super Mini DIG J1 CONN SOCKET RT ANG 1POS .050 Mill-Max Manufacturing ED8850-ND 851-43-010-20-001000

Connector Socket Corp.

10 3 Pin Jumper J2, J3, J4 CONN HEADER 3POS .100" SGL GOLD Samtec Inc SAM1029-03-ND TSW-103-07-G-S

11 DNP Socket J5 IC SOCKET MACH PIN ST 8POS TIN Assmann WSW AE10011-ND AR08-HZL-TT-R

Components

12 1 0 R7 RES, 0 Ω, 5%, 0.1W, 0603 Rohm RHM0.0GCT-ND MCR03EZPJ000

13 6 10 kΩ R1, R2, R3, R4, RES, 10.0 kΩ, 1%, 0.1W, 0603 Vishay-Dale 541-10.0KHCT-ND CRCW060310K0FKEA

R5, R6

14 3 845 R9, R10, R11 RES, 845 Ω, 1%, 0.1W, 0603 Yageo America 311-845HRCT-ND RC0603FR-07845RL

15 1 Temperature U1 IC TEMP SENSR Texas Instruments NA NA

Sensor

16 1 I

C Translator U2 IC LVL-TRANSL I2C BUS REP 8-SOIC Texas Instruments 296-23734-1-ND PCA9517DR

17 1 LDO U3 IC REG LDO 1.8 V .2 A TSOT-23-5 Texas Instruments 296-17778-1-ND TPS79918DDCR

18 4 Comparator U4, U5 IC COMPARATOR 1.8 V W/REF SOT23-6 Texas Instruments 296-16830-1-ND TLV3012AIDBVR

19 2 Shunt J2, J4 CONN JUMPER SHORTING .100" GOLD Sullins Connector S9341-ND NPC02SXON-RC

Solutions

TMP108EVM Evaluation Board and Software Tutorial SBOU129–April 2013

Submit Documentation Feedback

EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS

Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions:

The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims

arising from the handling or use of the goods.

Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from

the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO

BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH

ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES.

Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This

notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety

programs, please visit www.ti.com/esh or contact TI.

No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or

combination in which such TI products or services might be or are used. TI currently deals with a variety of customers for products, and

therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design,

software performance, or infringement of patents or services described herein.

REGULATORY COMPLIANCE INFORMATION

As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the Federal

Communications Commission (FCC) and Industry Canada (IC) rules.

For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING DEVELOPMENT,

DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer

use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing

devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against radio frequency

interference. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will

be required to take whatever measures may be required to correct this interference.

General Statement for EVMs including a radio

User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated frequency and

power limits. Any use of radio frequencies and/or power availability of this EVM and its development application(s) must comply with local

laws governing radio spectrum allocation and power limits for this evaluation module. It is the user’s sole responsibility to only operate this

radio in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this are strictly prohibited and

unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory

authorities, which is responsibility of user including its acceptable authorization.

For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant

Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the

equipment.

FCC Interference Statement for Class A EVM devices

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Interference Statement for Class B EVM devices

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For EVMs annotated as IC – INDUSTRY CANADA Compliant

This Class A or B digital apparatus complies with Canadian ICES-003.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

Concerning EVMs including radio transmitters

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired

operation of the device.

Concerning EVMs including detachable antennas

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain

approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should

be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum

permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain

greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada.

Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de

l'utilisateur pour actionner l'équipement.

Concernant les EVMs avec appareils radio

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est

autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout

brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Concernant les EVMs avec antennes détachables

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain

maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à

l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente

(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.

Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel

d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans

cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

SPACER

【【Important Notice for Users of this Product in Japan】】

This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan

If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product:

1. Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and

Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of

Japan,

2. Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this

product, or

3. Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law of Japan with

respect to this product. Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note

that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan.

Texas Instruments Japan Limited

(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan

http://www.tij.co.jp

【ご使用にあたっての注】

本開発キットは技術基準適合証明を受けておりません。

本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。

1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。

2. 実験局の免許を取得後ご使用いただく。

3. 技術基準適合証明を取得後ご使用いただく。

なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。

　　　上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。

日本テキサス・インスツルメンツ株式会社

東京都新宿区西新宿６丁目２４番１号

西新宿三井ビル

http://www.tij.co.jp

SPACER

EVALUATION BOARD/KIT/MODULE (EVM)

WARNINGS, RESTRICTIONS AND DISCLAIMERS

For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished

electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility evaluation in

laboratory/development environments by technically qualified electronics experts who are familiar with the dangers and application risks

associated with handling electrical mechanical components, systems and subsystems. It should not be used as all or part of a finished end

product.

Your Sole Responsibility and Risk. You acknowledge, represent and agree that:

1. You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food and Drug

Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that of your employees,

affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.

2. You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable

regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your employees, affiliates,

contractors or designees, using the EVM. Further, you are responsible to assure that any interfaces (electronic and/or mechanical)

between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to

minimize the risk of electrical shock hazard.

3. You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property damage, injury or death, even

if the EVM should fail to perform as described or expected.

4. You will take care of proper disposal and recycling of the EVM’s electronic components and packing materials.

Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and environmental considerations per the

user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output voltage, current, power, and

environmental ranges) may cause property damage, personal injury or death. If there are questions concerning these ratings please contact

a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the

specified output range may result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or

interface electronics. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the

load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures

greater than 60°C as long as the input and output are maintained at a normal ambient operating temperature. These components include

but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified using the

EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during normal operation, please

be aware that these devices may be very warm to the touch. As with all electronic evaluation tools, only qualified personnel knowledgeable

in electronic measurement and diagnostics normally found in development environments should use these EVMs.

Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their representatives

harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "Claims") arising out of or in

connection with any use of the EVM that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims

arise under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or expected.

Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical applications (such

as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, such as devices

which are classified as FDA Class III or similar classification, then you must specifically notify TI of such intent and enter into a separate

Assurance and Indemnity Agreement.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Page is loading ...

Texas Instruments TMP108EVM Users User guide

Brand: Texas Instruments

Model: TMP108EVM Users

Type: User guide

This manual is also suitable for

TMP108EVM

Texas Instruments TMP108EVM Users

Below you will find brief product information for Texas Instruments TMP108EVM Users:

TMP108EVM is used for reading temperatures between –40°C and +125°C with 12 bits of resolution.
TMP108EVM is ideal for extended temperature measurement and thermal management optimization in various applications.
TMP108EVM uses a two-wire I2C™ and SMBus™ interface that allows up to four devices on one bus.
TMP108EVM comes with the following contents upon purchase: TMP108EVM PCB Test Board (1), SM-USB-DIG Platform PCB (1), USB Extender Cable (1), 10-pin Connector Ribbon Cable (1), User’s Guide CD-ROM (1)

Download PDF

report

Texas Instruments TMP108EVM Users User guide

This manual is also suitable for

Texas Instruments TMP108EVM Users User guide

Related papers

Other documents