Panasonic DP-4530 User manual

Order Number: MGCS041001C0

H21

Digital Imaging Systems

DP-3510/4510/6010

DP-3520/4520/6020

DP-3530/4530/6030

[ Version 5.2 ]

This service information is designed for experienced repair technicians only and is not intended for use by the general public.

It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.

Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service

or repair the product or products dealt within this service information by anyone else could result in serious injury or death.

WARNING

a violation of law. Published in Japan.

2

The contents of this Service Manual and the Specifications are subject to change

without notice.

Panasonic Communications Co., Ltd. reserves the right to make improvements in

the product design without reservation and without notice.

Published in Japan.

Information regarding Lead-Free (PbF) solder:

Distinction of PbF PCB:

PCBs (manufactured) using lead free solder will have a mark following

the PCB part numbers in a label on the PCB.

Caution:

Pb free solder has a higher melting point than standard solder; typically

the melting point is 50 - 70 F (30 - 40 C) higher. Please use a soldering iron

with temperature control and adjust it to 700 20 F (370 10 C). Exercise care

while using higher temperature soldering irons, do not heat the PCB for too long

to prevent solder splash or damage to the PCB.

Pb free solder will tend to splash when heated too high (about 1100 F/600 C).

ECO SOLDER M705 (available from Senju Metal Industry Co., Ltd.:

URL: http://www.senju-m.co.jp) is recommended when repairing PbF PCBs.

This Product Uses Lead (Pb) Free Solder Printed Circuit

Boards (PCBs).

3

Important Notice

Please read this notice completely BEFORE installing any

optional accessories. As failure to properly install the additional

board or connector with the power ON (only the front power

switch Off) could damage the copier’s SPC or SC board.

Please follow the instructions below:

1.It is essential that you turn OFF power to the Main Power

Switch located in the rear of the copier.

2.It is essential that you unplug the Main AC Power Cord from

the wall outlet.

3.Please carefully read the installation instructions and follow

each step.

Note 1:

The Main Power Switch location may differ slightly depending on the model.

Note 2:

O = Power OFF, l = Power ON

Note:

If the Hard Disk Drive Unit is installed, to prevent a Disk Scan Function from being

performed (similar to when the power is abruptly interrupted to the PC), it is

important to follow the step sequence below when turning OFF the Power Switches on

the machine.

1. Turn the Power Switch on the Left Side of the machine to the OFF position first.

2. Wait approximately 10 seconds while the machine writes the closing status onto the Hard Disk

Drive Unit.

3. Turn the Main Power Switch on the Back of the machine to the OFF position.

(This interrupts all the power to the machine, but does not disconnect the main line.)

4. Unplug the AC Power Cord to shut the power Off completely.

* The specifications are subject to change without notice. Panasonic Communications Co., Ltd. reserves

the right to make improvements in the product design without reservation and without notice.

4

<Beispiel: DP-6530/4530/6030>

Hinweis:

5

Precautions

Power and Ground Connection Cautions

Ensure that the plug connection is free of dust. In a damp environment, a contaminated

connector can draw a significant amount of current that can generate heat and eventually

cause fire if left unattended over an extended period of time.

Always use the power cord provided with your machine. When an extension power cord is

required, always use a properly rated cord.

120 V/15 A or AC 220 - 240V/10 A

If you use a cord with an unspecified current rating, the machine or plug may emit smoke or

become hot to the touch.

Do not attempt to repair, pull, bend, chafe or otherwise damage the power cord. Do not

place a heavy object on the cord. A damaged cord can cause fire or electric shocks.

Never touch a power cord with wet hands. Danger of electric shock exists.

If the power cord is damaged or insulated wires are exposed, contact the authorized

Panasonic dealer

for a replacement. Using a damaged cord can cause fire or electric

Stop operation immediately if your machine emits smoke, excessive heat, unusual noise, or

abnormal smell, or if water is spilt onto the machine. These conditions can cause fire.

Immediately switch Off and unplug the machine, and contact the authorized Panasonic .

Do not disconnect or reconnect the machine while the power switch is in the On position.

Disconnecting a live connector can cause arcing, consequently deforming the plug and

cause fire.

When disconnecting the machine, grasp the plug instead of the cord. Pulling on a cord

forcibly can damage it and cause fire or electric shock.

When the machine is not used over an extended period of time, switch it Off and unplug it.

If an unused machine is left connected to a power source for a long period, degraded insulation

can cause electric shocks, current leakage or fire.

Be sure to switch Off and unplug the machine before accessing the interior of the machine

for cleaning, maintenance or fault clearance. Access to a live machine's

interior can cause

electric shock.

For Your Safety

To prevent severe injury and loss of life, read this section carefully before servicing the Panasonic

machine to ensure proper and safe operation of your machine.

This section explains the Warnings and Cautions used in the machine and/or this manual.

WARNING:

Denotes a potential hazard that could result in serious injury or death.

CAUTION:

Denotes hazards that could result in minor injury or damage to the machine.

This section also explains the Warnings and Cautions used in the machine and/or this manual.

These symbols are used to alert operators to a specific operating procedure

that must not be performed.

These symbols are used to alert operators to a specific operating procedure

that must be emphasized in order to operate the machine safely.

WARNING

Please ensure that the machine is installed near a wall outlet and is easily accessible.

shocks.

dealer.

6

Once a month, unplug the machine and check the power cord for the following. If you notice any unusual

condition, contact the authorized Panasonic dealer.

The power cord is plugged firmly into the receptacle.

The plug is not excessively heated, rusted, or bent.

The plug and receptacle are free of dust.

The cord is not cracked or frayed.

Operating Safeguards

Do not touch areas where these caution labels are attached to, the surface may be very hot and may cause

severe burns.

Do not place any liquid container such as a vase or coffee cup on the machine. Spilt water can cause fire or

shock hazard.

Do not place any metal parts such as staples or clips on the machine. If metal and flammable parts get into the

machine, they can short-circuit internal components, and cause fire or electric shocks.

If debris (metal or liquid) gets into the machine, switch Off and unplug the machine immediately.

Operating a debris-contaminated machine can cause fire or electric shock.

Do not try to alter the machine configuration or modify any parts. An unauthorized modification can cause

smoke or fire.

Consumable Safeguards

Never dispose of toner, toner cartridge or a waste toner container into an open flame. Toner remaining in the

cartridge can cause an explosion, burns and/or injuries.

Keep button batteries/stamp out of the reach of children. If a button battery/stamp is swallowed accidentally,

get medical treatment immediately.

Installation and Relocation Cautions

Do not place the machine near heaters or volatile, flammable, or combustible materials such as curtains that

may catch fire.

Do not place the machine in a hot, humid, dusty or poorly ventilated environment. Prolonged exposure to

these adverse conditions can cause fire or electric shocks.

Place the machine on a level and sturdy surface that can withstand the weight of the machine.

The weight of the machine : 43.6 kg / 96.12 lb

If tilted, the machine may tip-over and cause injuries.

When moving the machine, be sure to unplug the power cord from the outlet. If the machine is moved with the

power cord attached, it can cause damage to the cord which could result in fire or electric shock.

CAUTION

When relocating the machine, remove the toner and/or developer, and pack the machinee with proper

packing materials for shipping.

7

O

perating Safeguards

Do not place a magnet near the safety switch of the machine. A magnet can activate th

e

machine accidentally, resulting in injuries.

Do not use a highly flammable spray or solvent near the machine. It can cause fire.

When copying a thick document, do not use excessive force to press it against the scannin

g

glass. The glass may break and cause injuries.

Never touch a labelled area found on or near the heat roller. You can get burnt. If a sheet

of

paper is wrapped around the heat roller, do not try to remove it yourself to avoid injuries o

r

burns. Switch Off the machine immediately, and wait until it cools down.

Do not use conductive paper, e.g. folding paper, carbon paper and coated paper. When

a

paper jam occurs, they can cause a short circuit and fire.

Do not place any heavy object on the machine. An off-balance machine can tip-over or th

e

heavy object can fall, causing damage and/or injuries.

Keep the room ventilated when using the machine for an extended period of time to minimiz

e

the ozone density in the air.

When copying with the document cover open, do not look directly at the exposure lam

p.

Direct eye exposure can cause eye fatigue or eye injury.

Pull out paper trays slowly to prevent injuries.

When removing jammed paper, make sure that no pieces of torn paper are left in the machin

e.

A piece of paper remaining in the machine can cause fire. If a sheet of paper is wrappe

d

around the heat roller, or when clearing a jammed paper that is difficult or impossible to se

e,

do not try to remove it by yourself. Doing so can cause injuries or burns. Switch Off th

e

machine immediately, and wait until it cools down.

C

onsumable Safeguards

Never heat the drum cartridge, or scratch its surface. A heated or scratched drum can b

e

hazardous to your health.

Do not mix new and old batteries together, as they can burst or leak, causing a fire or

injuries. Be sure to use the specified type of batteries only..

Ensure that batteries are installed with correct polarity. Incorrectly installed batteries ca

n

burst or leak, resulting in spillage or injuries.

O

thers

When clearing a paper jam or other fault, follow the appropriate procedure given in this manual.

The machine has a built-in circuit for protection against lightning-induced surge current. If lightnin

g

strikes in your neighborhood, maintain an ample distance from the machine, and do not touch it

until the lightning stops.

If you notice flickering or distorted images or noises on your audio-visual units, your machine ma

y

be causing radio interference. Switch it Off and if the interference disappears, the machine is th

e

cause of the radio interference. Perform the following procedure until the interference is correcte

d.

Move the machine and the TV and/or radio away from each other.

Reposition or reorient the machine and the TV and/or radio.

Unplug the machine, TV and/or radio, and replug them into outlets operating on different circuit

s.

Reorient the TV and/or radio antennas and cables until the interference stops. For an outdoo

r

antenna, ask your local electrician for support.

Use a coaxial cable antenna.

CAUTION

Table of Contents

8

Specifications Table.................................10

1.1. Copy Function........................................ 10

1.2. Fax, Printer, Network Scanner and

Internet Fax Functions........................... 18

1.3. System Combination.............................. 27

1.4. Options and Supplies List...................... 28

1.5. External View......................................... 30

1.6. Control Panel......................................... 33

1.7. Fans and Motors.................................... 34

1.8. Sensors.................................................. 35

1.9. Clutches and Switches........................... 36

1.10. PC Boards.............................................. 36

Disassembly Instructions.........................37

2.1. General Disassembly............................. 37

2.2. Disassembly Instructions....................... 38

2.3. Screw Identification Template.............. 116

Maintenance, Adjustments and

Check Points..........................................122

3.1. Preventive Maintenance ...................... 122

3.2. Required Tools..................................... 124

3.3. Preventive Maintenance Points ........... 125

3.4. Preventive Maintenance Check List..... 127

3.5. Resetting the P/M

(Preventive Maintenance) Counter...... 129

3.6. Updating the Firmware......................... 131

3.7. Copy Quality Adjustment

Procedure (Order)................................ 142

3.8. Adjusting the Printer Registration,

LSU Image Side to Side....................... 146

3.9. QUANTUM Control in F8-14................ 147

3.10. Calibrating the LCD.............................. 149

Troubleshooting.....................................150

4.1. Initial Troubleshooting Flowchart......... 150

4.2. Improper LCD Display.......................... 151

4.3. Printed Copy Quality Problems............ 152

4.4. Troubleshooting the LAN Interface...... 168

4.5. Error Codes (For Copier)..................... 176

4.6. Information Codes Table

(For Facsimile)..................................... 191

4.7. Diagnostic Codes (For Facsimile)........ 197

4.8. Troubleshooting (For Printer)............... 204

Service Modes.......................................206

5.1. Service Modes (For Copier)................. 206

5.2. Service Modes (For Facsimile)............ 237

System Description................................266

6.1. Copy Process.......................................266

6.2. Precautions with Consumables............267

6.3. New Digital Image Control

Qualitative Reasoning Based

Adaptive Controller

(New Digital QUANTUM)......................269

6.4. Inverting Automatic Document

Feeder (i-ADF) .....................................271

6.5. Glossary of Electrical Abbreviations.....273

Installation .............................................282

7.1. Precautions During Set Up...................282

7.2. Unpacking ............................................284

7.3. Installation Procedure...........................285

7.4. Adjustment ...........................................290

Options and Supplies ............................291

8.1. Service Notes "Firmware Update"

for PCL-IPX/SPX or PS-IPX/SPX

Option Installation

(For DP-3530/4530/6030) ....................291

8.2. Service Notes "Firmware Update"

for PCL-IPX/SPX or PS-IPX/SPX

Option Installation

(For DP-3520/4520/6020) ....................295

8.3. Service Notes for "Firmware Update"

for PCL or PS Option Installation

(For DP-3510/4510/6010) ....................299

8.4. Installing the Printer Controller Module

for GDI-IPX/SPX (DA-GC601)

(Not Available in the USA/Canada)......303

8.5. Installing the Printer Controller Module

for PCL6-IPX/SPX (DA-PC602) ...........304

8.6. Installing the Printer Controller Module

for PCL6-IPX/SPX (DA-PC601) ...........306

8.7. Installing the Printer Controller Module

for PCL6 (DA-PC600)...........................308

8.8. Installing the Printer Controller Module

for PS / PCL6-IPX/SPX

(DA-MC602).........................................310

8.9. Installing the Printer Controller Module

for PS / PCL6-IPX/SPX

(DA-MC601).........................................312

8.10. Installing the Printer Controller Module

for PS / PCL6 (DA-MC600)..................314

8.11. Installing the Network Scanner Module

(DA-NS600)..........................................316

8.12. Installing the Network Scanner Module

for DDS (DA-NS601)............................317

8.13. Installing the Internet Fax / E-Mail

Module (DA-NF600).............................319

Table of Contents

9

8.14. Installing the Fax Communication

Board (DA-FG600)................................323

8.15. Installing the Hard Disk Drive Unit

(DA-HD60)............................................332

8.16. Installing the Accounting Software

(DA-WA10) ...........................................338

8.17. Installing the DD Server Software

(DA-WS20) ...........................................339

8.18. Installing the Expansion F-ROM

Board (DA-EM600)...............................340

8.19. Installing the Sorting Image Memory

16/64/128 MB

(DA-SM16B/64B/28B)...........................341

8.20. Installing the Expansion Flash

Memory Card 4/8 MB

(UE-410047/410048)............................342

8.21. Installing the System

Console 1 (DA-DS603) /

Console 2 (DA-DS604).........................343

8.22. Installing the System

Console 1 (DA-DS601) /

Console 2 (DA-DS602).........................346

8.23. Installing the 3000-Sheet Tray

(DA-MA301)..........................................349

8.24. Installing the Letter / Legal Size

Adapter for 3000-Sheet Tray

(DA-TK31).............................................352

8.25. Installing the Exit Tray (DA-XT600)......357

8.26. Installing the 2 Bin Finisher

(DA-FS600)...........................................360

8.27. Installing the 2 Bin Saddle-Stitch

Finisher (DA-FS605).............................371

8.28. Installing the Punch Unit

(DA-SP31) ............................................384

8.29. Installing the 2 Bin Finisher

(DA-FS330)...........................................388

8.30. Installing the 1 Bin Saddle-Stitch

Finisher (DA-FS355A) ..........................394

8.31. Installing the Punch Unit (DA-SP41).....403

8.32. Installing the Power Supply for Finisher

(DA-PW600) .........................................411

8.33. Installing the Key Counter Harness Kit

(DZTY000128)......................................413

8.34. Installing the Dehumidifier Heater

(DZTQ000041)......................................415

8.35. Installing the Stand

(DA-D351/D352)...................................423

8.36. Replacing the OPC Drum.....................426

General Network Information.................429

9.1. Network Protocol ..................................429

9.2. Layer Functions and Technology..........431

9.3. Network Layer......................................435

9.4. Transport Layer....................................439

9.5. Upper Layer .........................................441

9.6. SMTP

(Simple Mail Transfer Protocol)............446

9.7. ITU T.37 and RFC2305........................447

9.8. Communication Protocols ....................453

9.9. POP

(Post Office Protocol Version 3)...........456

9.10. Troubleshooting from a PC ..................459

9.11. Verifying the Configuration and

Mail Account Type (SMTP or POP) .....460

9.12. Dynamic Host Configuration Protocol

(DHCP) - Extended Feature.................461

9.13. Message Disposition Notifications

(MDN) - Extended Feature...................464

9.14. Lightweight Directory Access Protocol

(LDAP) - Extended Feature..................468

9.15. Lightweight Challenge-response

Mechanism POP (APOP)

- Extended Feature ..............................468

9.16. SMTP Service Extension

for Authentication (SMTP Auth)

- Extended Feature ..............................470

9.17. Direct Internet Fax XMT

- Extended Feature ..............................472

Schematic Diagram...............................473

10.1. General Circuit Diagram.......................473

Finisher Options ....................................475

11.1. DA-FS600, DA-FS605, DA-SP31.........475

11.2. DA-FS330 ............................................677

11.3. DA-FS355, DA-SP41 ...........................715

10

JAN 2006

Ver. 5.2

DP-3510/3520/3530/4510/4520/4530/6010/6020/6030

1 Specifications Table

1.1. Copy Function

Items

Description

Remarks

DP-3510/

3520/3530

DP-4510/

4520/4530

DP-6010/

6020/6030

Basic Specifications

1 Type Console

2 Platen Fixed

3 Original Position Left

4 Recording Paper Path Center

5 Face Up / Face Down Face Down

6 Drum Organic Photo Conductor (OPC)

7 Copy Process Dry Electrostatic System

8 Developing Process

Magnetic Dual Component Development

System

9 Toner Recycle No

10 Fusing System Heat & Pressure

11 Max Original Size

Ledger (11 x 17 in) /

A3 (297 x 420 mm)

12 Paper Size

1st Paper Tray

(1,550 Sheet Paper Tray)

LTR For USA and Canada

A4 For EU

A4 For Other Destinations

Paper Tray

LDR, LGL, LTR, LTR-R, INV-R For USA and Canada

A3, A4, A4-R, A5-R, B4 (FLS) For EU

A3, A4, A4-R, B4, B5, B5-R For Other Destinations

Sheet Bypass

LDR, LGL, LTR, LTR-R, INV-R For USA and Canada

A3, A4, A4-R, A5-R, B4 (FLS) For EU

A3, A4, A4-R, B4, B5, B5-R For Other Destinations

Sheet Bypass Envelope No

13 Warm-up Time

Less than

30 sec.

Less than

180 sec.

68 °F (20 °C)

14 First Copy Time

Less than

5.8 sec.

Less than

4.5 sec.

Less than

3.5 sec.

From Platen/ Letter/ A4

Portrait/ 1st Paper Tray.

Period between Start Key is

pressed and Paper ejected.

15 Copy Speed

Ledger / A3 20 cpm 27 cpm 34 cpm

Legal / B4, FLS 23 cpm 31 cpm 39 cpm

Letter-R 28 cpm 37 cpm 49 cpm

A4-R 27 cpm 36 cpm 48 cpm

LTR / A4 35 cpm 45 cpm 60 cpm

16 Zoom

Enlargement Selected Original size / Copy size

Reduction Selected Original size / Copy size

Zoom 25 - 400% 1% Step

11

JAN 2006

Ver. 5.2

DP-3510/3520/3530/4510/4520/4530/6010/6020/6030

17 Maximum Tray Capacities Front loading universal Paper Tray

Paper Tray

USA and Canada

LTR : 20 lb (75 g/m

2

)

Other Destinations

A4 : 80 g/m

2

Capacity

1,550 sheets x 1

550 sheets x 1

Auto Size Setting Yes (2nd Tray only)

Low Level Warning Empty only

Sheet Bypass

Capacity 50 sheets

Auto Size Setting Yes

Paper Capacity

(Std. Configuration)

2,150 sheets

Max. Paper Capacity 6,250 sheets

18 Acceptable Paper Weight

Paper Tray

16-24 lb / 60-90 g/m

2

Sheet Bypass

15-35 lb / 55-133 g/m

2

19 Inverting ADF (i-ADF)

Duplex Type

Yes (Standard) For USA, Canada and EU

Option Yes (Standard) For Other Destinations

Original Set Face Up

Scanning Method Sheet Through

Capacity (Original) 70 sheets (LTR / A4)

USA and Canada

LTR : 20 lb (75 g/m

2

)

Other Destinations

A4 : 80 g/m

2

SADF Mode Yes

Available for single side

scanning only.

Free Stop Yes From 30 to 70 degrees.

20 Multi Copy Range 1-999 sets

21 Gradation

Text 2 steps

Text / Photo 2 step error diffusion

Photo 256 steps

22 Resolution 600 dpi Scanning and Printing.

23

Standard Sorting Memory

Size

32 MB

24 Standard Page Memory Size 20 MB For Printing.

25 Exit Tray Capacity 250 sheets

26 Color No

27 Dimensions

(W x D x H)

23.6 x 29.6 x 29.0 in

(600 x 753 x 736 mm)

H: Up to Platen Glass.

23.6 x 29.6 x 35.4 in

(600 x 753 x 900 mm)

H: Up to i-ADF.

Items

Description

Remarks

DP-3510/

3520/3530

DP-4510/

4520/4530

DP-6010/

6020/6030

12

JAN 2006

Ver. 5.2

DP-3510/3520/3530/4510/4520/4530/6010/6020/6030

28 Occupancy Area

(W x D)

47.2 x 29.6 in

(1,200 x 753 mm)

Includes Bypass Paper

Tray.

29 Weight

251 lb

(114 kg)

258 lb

(117 kg)

258 lb

(117 kg)

Main Unit only,

without i-ADF.

283 lb

(128.5 kg)

290 lb

(131.5 kg)

290 lb

(131.5 kg)

Main Unit with i-ADF.

Options

1 Paper Feed System

550 sheets x1 (3rd)

Paper Feed Module

Yes

<DA-DS601>

USA and Canada

LTR : 20 lb (75 g/m

2

)

Other Destinations

A4 : 80 g/m

2

Paper Size Detection Manual (Control Panel)

Low Level Paper Warning Empty only

Dimensions

(W x D x H)

23.6 x 28.7 x 11.4 in

(600 x 730 x 290 mm)

Weight 63.5 lb (28.8 kg)

550 sheets x 2 (3rd/4th)

Paper Feed Module

Yes

<DA-DS602>

USA and Canada

LTR : 20 lb (75 g/m

2

)

Other Destinations

A4 : 80 g/m

2

Paper Size Detection Manual (Control Panel)

Low Level Paper Warning Empty only

Dimensions

(W x D x H)

23.6 x 28.7 x 11.4 in

(600 x 730 x 290 mm)

Weight 66.1 lb (30.0 kg)

3000 sheets

Paper Feed Module

Letter : 3,000 sheets

Letter-R : 2,500 sheets

Legal : 1,500 sheets

<DA-MA301>

LTR / LGL : 20 lb (75 g/m

2

)

Paper Size Detection Manual (Control Panel)

Low Level Paper Warning Empty only

Dimensions

(W x D x H)

11.6 x 17.5 x 19.9 in

(295 x 445 x 505 mm)

17.4 x 17.5 x 19.9 in

(442 x 445 x 505 mm)

With LTR-R / LGL Size

Adapter (DA-TK31)

Weight

27.1 lb (12.3 kg)

37.0 lb (16.8 kg)

With LTR-R / LGL Size

Adapter (DA-TK31)

Max. Paper Capacity 6,250 sheets

2 1-Bin Saddle-Stitch Finisher Yes

-

DA-FS355A

3 2-Bin Finisher Yes

-

DA-FS330

4 2-Bin Finisher

-

Yes DA-FS600

5 2-Bin Saddle-Stitch Finisher

-

Yes DA-FS605

6 Counter

Key Counter Capability Yes

7 Dehumidifier Yes

Supplied as service part.

Part Number: DZTQ000041

Items

Description

Remarks

DP-3510/

3520/3530

DP-4510/

4520/4530

DP-6010/

6020/6030

13

JAN 2006

Ver. 5.2

DP-3510/3520/3530/4510/4520/4530/6010/6020/6030

8 Electronic Sorting Board Standard (32 MB) CODEC + 32 MB memory

Optional Image Memory 1

(16 MB)

Yes

Only one of three available

types can be installed.

Optional Image Memory 2

(64 MB)

Yes

Optional Image Memory 3

(128 MB)

Yes

Features

1 Automatic Features

Auto Magnification Selection Yes

Auto Paper Selection Yes

Auto Density Control Yes

Auto Paper Tray Selection Yes

Auto Start Yes

Reservation while Power

On Initializing

Energy Saver Mode

Standby Mode Yes

Energy Saver Mode Yes

Sleep Mode Yes (20W)

Turns Off the Heater

Power.

NW Function available

Auto Off Mode

Yes (4W)

For USA, Canada and EU

With Finisher Power Supply

NW Function not available

Yes (3W)

For Other Destinations

Without Finisher Power

Supply

NW Function not available

Remote Diagnostic Yes

Requires the Fax

Communication Board

(DA-FG600) option.

Machine Stops while Out of

Toner

Yes

Copier function

2 Additional Features

Low Level Paper Warning Empty only

Photo Mode Yes 256-step (Gray Scale)

Original Detection Release Yes

Manually overriden when

using the Original Size

keys.

Edit / Effects

Book Mode Yes

Edge Mode Yes

Margin Mode Yes

X-Y Zoom Yes 25 - 400%

Page Numbering Yes

Available only when using

the ADF.

Inverse Mode (Negative /

Positive)

Yes

Items

Description

Remarks

DP-3510/

3520/3530

DP-4510/

4520/4530

DP-6010/

6020/6030

14

JAN 2006

Ver. 5.2

DP-3510/3520/3530/4510/4520/4530/6010/6020/6030

Centering Mode Yes

Mirror Mode No

Others (Inverting ADF &

ADU)

2-Page Copy Mode Yes

LDR → LTR x 2

(A3 → A4 x 2, B4 → B5 x 2)

2 in 1 Yes

4 in 1 Yes

6 in 1 Yes

8 in 1 Yes

Booklet Mode Yes

Copy from 4 single-sided

pages to 1 booklet mode

sheet.

Duplex Copy

1→2Yes

2→1Yes

2→2Yes

Book→2Yes

Book Format Yes

Facing Pages Yes

Image Rotation (90 degrees) Yes

Electronic Sorting Yes

Rotation Sorting Yes

Insertion Job

Cover Mode Yes

Page Insertion Mode Yes

OHP Interleave Mode Yes Non-copy / Copy

Presentation Mode Yes

Department Counter Yes 300 Departments

i-ADF

Multi Size Feed Yes

LDR and LTR, LGL and

LTR-R, A3 and A4, B4 and

B5, A4-R and A5

SADF Mode Yes

Original Counter No

Job Memory Yes (5)

Job Time Display No

Concurrent Copy Yes (12)

Tandem Copy Mode Yes

Remote Copy Mode Yes

Scan Once Print Many Mode Yes

Job Complete Notice Yes

Trial Copy Mode Yes

Weekly Timer Yes

User Mode Yes

Interrupt Yes

Items

Description

Remarks

DP-3510/

3520/3530

DP-4510/

4520/4530

DP-6010/

6020/6030

15

JAN 2006

Ver. 5.2

DP-3510/3520/3530/4510/4520/4530/6010/6020/6030

Electronic Counter Yes

Digital Sky Shot Mode

Yes

Check / Slip Mode Yes

3 Control Panel

Display Wide Touch Panel LCD

Status Lamp Yes

GREEN : Scanning /

Printing

RED : Alarm / Warning

Key

Original Size Yes

Copy Size Yes

Keypad Yes

Clear Yes

Stop Yes

Start Yes

Energy Saver Yes

Function Yes

Interrupt Yes

Reset Yes

One-Touch Key No

Mode Change Yes

Copier / Printer / NW

Scanner / Fax and Internet

Fax Mode change.

LCD Main Indication

Message Language

(Default)

English (American) For USA and Canada

Specified Language

For EU and Other

Destinations

Original Size / Image

Indication

Yes

(with Image)

Paper Size / Image

Indication

Yes

(with Image)

Paper Tray Selection Yes

Selected Paper Tray

Status

Yes

Original Mode Selection Yes Text / Text-Photo / Photo

Copy Density Selection Yes

Setting Confirmation Yes

Zoom Magnification Yes

Function Classification Yes

Number of Copies Yes

SADF / Multi Size Feed

Mode

Yes

Error Code Yes

Finishing Yes

Warning Indicators Yes

Add Toner Yes

Items

Description

Remarks

DP-3510/

3520/3530

DP-4510/

4520/4530

DP-6010/

6020/6030

16

JAN 2006

Ver. 5.2

DP-3510/3520/3530/4510/4520/4530/6010/6020/6030

Toner Waste Container

Full

Yes

Add Paper (No Paper) Yes

Add Paper

(Under 50 Sheets)

No

Paper Jam Indication Yes

Paper Jam Location Yes

Service Alert Call Yes

User Error Yes

Machine Error Yes

History of Jam Errors Yes

4 Main Unit

Total Counter Yes (Standard) Mechanical Counter

Max. Weight of Documents

on the Platen Glass

11 lb (5 kg)

ADF with Document Guide Yes

Clip Pocket Yes

Operating Instructions

Pocket

No

Warning / Caution Label Specified Language

5 Optical System

Original Detection Method Reflective Photo Sensor Type

Scanning Method 600 dpi CCD

Dehumidifier Yes

Supplied as a Service Part

Part Number: DZTQ000041

Mechanical Multi Copy

Mode

No

6 Process System

Type

Separate OPC Unit and

Developer Unit Type

Toner 24K 35K

Developer Life 240K

Drum Life 240K LTR / A4

Toner Waste Container 240K

Dehumidifier Yes

Supplied as a Service Part

Part Number: DZTQ000041

Manual Add Toner Yes

Manually adds toner to the

developer

(up to TDC threshold)

Efficiency

1 Productivity

Warm-Up Time from

Standby

Approx.

30 sec.

Approx.

180 sec.

68 °F (20 °C)

ADF Productivity (LTR / A4)

Inverting ADF 100% Throughput

Items

Description

Remarks

DP-3510/

3520/3530

DP-4510/

4520/4530

DP-6010/

6020/6030

17

JAN 2006

Ver. 5.2

DP-3510/3520/3530/4510/4520/4530/6010/6020/6030

ADU Copy Productivity

(LTR / A4)

When ejecting to Outer

Tray

Transport Method Stackless

1→2

1 copy 45%

Throughput

5 copies 75%

10 copies 90%

PM Cycle

1PM Cycle

Major PM 120K 120K 240K

Minor PM (Cleaning)

--

120K

Packing Configuration

1 Packing Dimension

(W x D x H)

28.5 x 34.3 x 42.9 in

(725 x 870 x 1090 mm)

2 Packing Weight

302 lb

(137 kg)

309 lb

(140 kg)

For USA and Canada

298 lb

(135 kg)

304 lb

(138 kg)

For EU and

Other Destinations

3 Accessories

OPC Unit Yes

Developer No

Toner No

Toner Waste Container Yes

Outer Tray

Option For USA and Canada

Yes

For EU and

Other Destinations

Operating Instructions Yes

Power Supply

1 Power Requirement

99 - 138 VAC, 47 - 63 Hz

Single phase

100 VAC Power Supply

180 - 264 VAC, 47 - 63 Hz

Single phase

220 VAC Power Supply

2 Power Consumption Less than 1500 W

Ambient Conditions

1 Temperature 50 - 80 °F (10 - 30 °C)

2 Relative Humidity 30 - 80%

3Safety

UL1950 / CSA C22.2 No.950 For USA and Canada

EN60950

For EU and

Other Destinations

4 Energy Saver Energy Star Compliant

5EMI

Class A computing device in FCC Rules

Part 15

For USA and Canada

6 Lead Free Solder (PbF) This Product uses Lead Free (PbF) PCBs

Refer to the Part Manual for

details

Items

Description

Remarks

DP-3510/

3520/3530

DP-4510/

4520/4530

DP-6010/

6020/6030

18

JAN 2006

Ver. 5.2

DP-3510/3520/3530/4510/4520/4530/6010/6020/6030

1.2. Fax, Printer, Network Scanner and Internet Fax Functions

1.2.1. Fax Function

Items

Description

Remarks

DP-3510/

3520/3530

DP-4510/

4520/4530

DP-6010/

6020/6030

Main Specifications

1 Compatibility G3 ITU-T Std. & Non-Std. (PCC)

2 PSTN Line Port Yes 1-Line Only

3 Leased Line Port No

4 V.24 Line Port No

5 Modem Speed 33.6 - 2.4 kbps

6 Coding Scheme JBIG / MMR / MR / MH

7 ECM Yes Conforms to ITU-T

8 Short Protocol Yes (B, D)

9 Transmission Speed Approx. 3 sec.

ITU-T Image No. 1

(A4, Std. Resolution)

10

Communication Resolution

(pels/mm x lines/mm)

Transmission

Std. 8 x 3.85

Fine 8 x 7.7

S-Fine 8 x 15.4

16 x 15.4

600dpi 600 x 600 dpi

Reception

Std. 8 x 3.85

Fine 8 x 7.7

S-Fine 8 x 15.4

16 x 15.4

600dpi 600 x 600 dpi

Scanner Mechanism

1 Scanning Device CCD (i-ADF / Platen)

2 Scanning Speed

Resolution Vertical Horizontal

A4, Scanned in Vertical or

Horizontal Direction

Std: 8 x 3.85

(pels/mm x lines/mm)

1.0 sec. 0.7 sec.

Fine: 8 x 7.7

(pels/mm x lines/mm)

1.0 sec. 0.7 sec.

S-Fine: 16 x 15.4

(pels/mm x lines/mm)

2.0 sec. 1.4 sec.

600dpi: 600 x 600 2.0 sec. 1.4 sec.

3

Scanning Resolution

(pel/mm x lines/mm)

Std. 8 x 3.85

Fine 8 x 7.7

S-Fine 8 x 15.4

16 x 15.4

600dpi 600 x 600 dpi

4 Document Size (Max.) ADF: Ledger / A3

5 Effective Scanning Width LDR (11.5 in) / A3 (292 mm)

6 A3 size TX / RX Yes Conforms to ITU-T A3

7 Reduction XMT Yes A3 to B4 / A3 to A4 / B4 to A4

19

JAN 2006

Ver. 5.2

DP-3510/3520/3530/4510/4520/4530/6010/6020/6030

8 ADF Capacity 70 sheets Face-Up, feed from top page

9 Collation Stack Yes Face Down

Printer Mechanism

1 Recording Method LP

2 Recording Speed

35 ppm

(A4

Horizontal)

45 ppm

(A4

Horizontal)

60 ppm

(A4

Horizontal)

3 Recording Resolution Fax

600 x 600 dpi

406 x 391 dpi

4 Recording Paper Size Ledger / Legal / Letter / A3 / B4 / A4 / A5

Invoice : Not supported.

Ledger size is transmitted as

A3 size for N. American

models. If A3 is received,

approx. 1" of image on both

edges are not printed on

Ledger size paper.

5 Effective Printing Width 11.4 in (289 mm) Conforms to ITU-T A3

6 Recording Paper Capacity

2,150 sheets

Optional max. 6,250 sheets

7 Collation Stack Yes Face Down

8 Consumables Toner Bottle, OPC Drum and Staples

Fax Memory

1 Standard Memory

DP-3530/4530/6030:

3 MB (180 pages)

DP-3510/3520/4510/4520/6010/6020:

2 MB (120 pages)

Flash ROM, ITU-T Image No.1

(A4, Std. Resolution)

2 Optional Memory

4 MB

8 MB

Expansion Flash Memory

Card

Dual Operation

1 Multi Task Operation Yes

2 Direct XMT Reserve Yes

3 Memory XMT Reserve Yes

4

Number of Memory Job

Files

Yes (Max. 50 files)

Dialing/Telephone Features

1 Address Book Dialing 200 Stations

Plus an additional 800 stations

available to select from, when

the optional Hard Disk Drive

(DA-HD60) is installed.

2

Full Number Dialing

(Buffered Dialing)

Yes Max. 70 stations

3

Address Book Directory

Search Dialing

Yes

4 Total Auto Dialers 270 Stations

200 Address Book + 70 Full

Number Dialing

5 Program Dials 12

6 Max. Tel Number Digits 36

Items

Description

Remarks

DP-3510/

3520/3530

DP-4510/

4520/4530

DP-6010/

6020/6030

20

JAN 2006

Ver. 5.2

DP-3510/3520/3530/4510/4520/4530/6010/6020/6030

7

Max. Station Name

Characters

15

8

Direct Dialing

(Monitor Dialing)

Yes Voice mode

9 Automatic Redialing Yes

10 Manual Redialing Yes

11 Line Monitor Speaker Yes Available for Line-1 only

12 Chain Dialing (Hybrid Dial) Yes In Monitor Dialing mode only

13 Pulse / Tone Dialing Yes 10 pps / DTMF

14 Pulse to Tone Change Yes

15 Flash Key Yes

16 Handset No

Transmission Features

1 Direct Transmission Yes

2 Memory Transmission Yes Page Retransmission

3

Quick Memory

Transmission

Yes

4

Multi-Station Transmission

(Sequential Broadcasting)

Yes Max. 270 Stations

5

Direct Deferred

Transmission

No ADF Deferred Transmission

6 Deferred Transmission Yes Max. 50 Timers

7

Deferred Multi-Station

Transmission

Yes

8

Priority Direct

Transmission

Yes Priority ADF Transmission

9

Priority Memory

Transmission

No

10 Batch Transmission Yes Real Time (up to 5 Files)

11

90 Degree Rotation

Transmission

Yes

12 Cover Sheet Yes

13 Confidential Mail Box Yes 20 Mailboxes

14 Multi-Copy Transmission No

15 Memory Back-Up Yes

FAX : Back-up with Flash

Memory.

Copy / Printer : No Back-up

with D-RAM

16 Duplex Scanning Yes With Inverting ADF (i-ADF)

Reception Features

1 Substitute Reception Yes

2 Fixed Reduction Yes

LTR/A4/LGL: 70 - 100%

(in 1% Steps),

Top & Left Alignment

3 Auto Reduction Yes

LTR/A4/LGL: 70 - 100%

(in 1% Steps),

Top & Left Alignment

Items

Description

Remarks

DP-3510/

3520/3530

DP-4510/

4520/4530

DP-6010/

6020/6030

Page is loading ...

Panasonic DP-4530, DP-3530, DP-6030, Workio DP-3510, WORKIO DP-3520, Workio DP-4510, WORKIO DP-4520, Workio DP-6010, WORKIO DP-6020 User manual

Related papers

Other documents