11.75”-15.75”
DAY
NIGHT
Indirect Sunlight
Backlight
Direct Sunlight
at least 10’
30°
30°
At least 7’ away from any light source.
Do not position light source within 30° view.
At least 10’ away from windows or doors.
at least 7’
STEP 2
Device Installation
Device Quick Start Guide BracketDrill Template
Plastic Plugs (4x)Screws (4x)
FRONT LEFT RIGHT BACK
IR Temperature
Measurement Module
White Fill
Light
Infrared
Light
Cameras
Display
Screen
Speaker
MicroSD
Card Slot
Reset
USB Port
Microphone
18-Pin
Interface
Power
Interface
Recommended Installation Height: 51” - 57”
Ideal Measurement Range
51” - 57”
11.75”
15.75”
To ensure accurate temperature readings, measurements must be taken on
a fully exposed forehead at proper distance and height from unit.
Alarm
Input1
Power
Input
Alarm
Output1
Alarm
Input2
RS-485
Alarm
Output2
Lock
Wiegand
Interface
Exit
Button
2CH Alarm Output Lock Interface RS-485 Wiegand Interface2CH Alarm Intput Exit Button
Notes:
• The Wiegand terminal is a Wiegand Input Terminal.To connect
to access controller, set Wiegand direction to “Output”.
• The RS-485 interface supports security module access. The
Exit Button and Lock Control are disabled when the security module
is enabled.
Package Contents
Device Overview
QUICK START GUIDE
VT-TSP8
All-In-One Body Temperature
Detecting Facial Recognition
Access Control Camera with
Integrated 8” LCD Display
1) Place drill template onto wall, then drill holes accordingly.
2) Install gang box on the wall, use two screws to secure the
bracket to the gang box, then use four screws to finish
securing bracket to the wall.
3) Route and connect cables, then install cable cover.
4) Hang device on bracket hook, then tighten screws to secure.
Cover Plate
Security Screws (6x)
Hex Wrench
(2 Amp)
www.vitekcctv.com | Support@vitekcctv.com
STEP 1
Pre-Installation Planning
DEVICE LOGIN / ACCESSING THE MAIN MENU
1
Tap the Menu button in the lower right
of the screen, enter the Username and
Password in the login box, then tap
“OK” to enter the main menu page.
Default Username: admin
Default Password: 123456
Menu Button
Main Menu Options:
• Face Config
• Data Record
• Device Maintenance
• System Settings
• Network Config
• Access Control Settings
MAIN MENU
2
In the Main menu page of the terminal,
tap “Network Config” to go to the
network config interface.
Configure as needed, then tap to
save your changes.
NETWORK CONFIGURATION
3
Temperature Measurement
Temperature Settings
System Settings
TEMPERATURE MEASUREMENT SETTINGS
4
The Temperature Measurement
Settings can be access from the
Main Menu by selecting:
Configure as needed, then tap
to save your changes.
Temperature Measurement
Mask Detection
System Settings
MASK DETECTION SETTINGS
5
The Mask Detection Settings can
be access from the Main Menu by
selecting:
Configure as needed, then tap to save your changes.
Alarm Out: If enabled, alarm output will be triggered when the detected
person doesn’t wear a mask.
Trigger Audio Alarm: If enabled, the alarm voice will be heard when the
detected person doesn’t wear a mask.
Activate by selecting "Enable".
Set the alarm holding time.
Set the alarm trigger options.
People Management
Click “+” (To Add User)
Face Config
PEOPLE MANAGEMENT: ADDING USERS
6
The People Management Settings
can be access from the Main Menu
by selecting:
www.vitekcctv.com | Support@vitekcctv.com
STEP 3 Configuration
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Geovision GV-CR420 User manual
-
Geovision GV-VS11 User manual
-
Comelit IPTHPAN02FA User manual
-
Grandstream GDS3710 User manual
-
-
-
Geovision GV-CR1320 User manual
-
Grandstream GDS3705 User manual
-
Geovision GV-CS1320 User manual
-
ACTi R72FT-31 User manual