BrickHouse Security NANO-XB-REF User manual

BrickHouse Security

Brand: BrickHouse Security

Model: NANO-XB-REF

Type: User manual

WHEN YOU NEED TO KNOW.

Spark Nano 5.0

User’s Guide

What’s Inside

Spark Nano 5.0

Wall Charger

Optional Accessories

Weatherproof Magnetic GPS Box

Reduces the risk of physical damage to

your device

Spark Nano 5.0

1. Power Button

2. Charging Port

3. Panic Button

4. GPS LED

5. CDMA LED

6. BatteryLED

1

2

4

3

5

6

LED

GPS LED: Blue Light

1. Remains off when the tracker is idle.

2. When the tracker has sensed motion, the GPS LED will steadily blink,

indicating that it has received GPS signal.

Power LED: Orange Light

1. The orange light will blink to indicate that the tracker is charging. After

the battery is full, the battery light will stay lit.

When the battery is low, the Power LED will blink orange at a steady pace

indicating that the battery will need to be charged soon.

Note: If the device has not been charged for a long period of time, the

orange light may take a few hours to light up and start blinking. If you have

not charged the device for a long time and the light does not light up when

the device is plugged in, please allow at least 6 hours of charge, and then try

to power the device on.

CDMA Signal LED: Green Light

1. This LED blinks to indicate that the device has successfully connected

to the CDMA network.

If there are no CDMA networks connected, the light will remain off.

Note: When the device is sitting idle, only the green light will blink if it has

connected to the cellular network.

Getting Started

You should have received an email containing your default login information;

this will be used to conﬁgure your device and view tracking information (which

will be covered later in this user’s guide).

The ﬁrst step in using your Spark Nano 5.0 is to charge it. To charge, plug the

AC adapter into a wall outlet and connect the charger to the charging port.

Charge the Nano for at least 6 hours before ﬁrst use. When fully charged, the

orange light will glow solid (and then stop glowing after a prolonged period of

remaining plugged in after it’s fully charged). When the device is done charging,

disconnect it from the charger and press the power button to turn the device

on. Make sure all the rubber port covers are securely in place before ﬁrst use.

Your Nano may take up to 24-48 hours to activate on the Verizon network once

it’s charged. To make sure your Nano registers on the satellite network, we

suggest placing the device on the dashboard of a car and taking it for a drive for

20-30 minutes. It is important that the tracker have a clear view of the sky. Since

the device is motion-activated, it is not sufﬁcient to leave it outside or on a window

sill for it to register. It must be moving in order to register and report its location.

To power on the unit, hold down the power button for around 3 seconds.

You’ll see a light reaction. To power off the device the power button needs

to be pressed twice rapidly and held down on the 2nd press, until the red

indicator light turns on. Note: It can take up to a minute for the device to

power down after the red indicator light turns on.

Placing Your Device

*Place in green zones for best results.

Your Spark Nano will always

give the most accurate

location data when it has

a clear view of the sky. It is

capable of transmitting and

receiving through materials

like glass, plastic, and cloth,

but is not able to transmit

through metals. Keep this

in mind when placing the

device. Avoid placing the device in the trunk of a vehicle. It may or may not

report from a glove compartment or underneath a seat. This interference

can vary from vehicle to vehicle, however, as all automobiles are constructed

differently.

If you want to track covertly, the Weatherproof Magnetic GPS Box may be the

best solution for you. When placing the device beneath a vehicle, be sure that

the side with the LEDs is facing down, toward the ground, and that it is as

near the edge of the vehicle as possible.

Tracking Your Device

To track your Nano, open a browser window and go to

www.BrickhouseSecurity.com. Hover your cursor over the Login tab on the top

right of the website and click on GPS Tracking. Enter your login information and

press the Submit button. The tracking page will appear, and the device’s last

reported location will be centered on the map. If you have multiple devices on

your account, the ﬁrst 3 that were registered will be automatically selected and

appear on the map. Along the bottom of your screen will be your dashboard.

Navigation Arrows

Zoom Bar Dashboard Last Known Location

Change Map View

Tracking information is displayed using Google Earth Maps, so navigation

is similar to what most people have grown used to in using internet-based

mapping solutions. You can use the Navigation arrows and Zoom Bar to move

around the map, or drag the map using your mouse and zoom using a click-

wheel mouse.

At the bottom of the pop-up window are the Zoom, Street View, and Live

Tracker buttons.

• Zoom will perform the same task as using the Zoom bar on the left side of

the map; zooming in on the icon you have selected.

• Street View will open up a separate window displaying Google’s Street

View, if available.

The BrickHouse shield icon will appear where a tracker transmitted most

recently. Click on an icon to bring up a pop-up box. This will show your

tracker’s name, the distance it has traveled on this trip, what direction it was

moving in, speed, battery information, and start and stop locations. Start will

display the beginning location of the current trip, and the time it was recorded.

Stop will display the most recent location from the device, as well as the time

it was reported.

The More tab is not currently active. Future updates to the platform will utilize

this tab.

The GeoFence tab allows you to create quick geofences, based on the

location you are currently viewing and route the device was following. Use the

Circular GeoFence radio button to create a perimeter around the location you

are clicked on. Use the Route GeoFence radio button to create a boundary

that will follow the entire trip your device was on.

Give the GeoFence a name in the GeoFence Name window, and add a short

description in the Description box (optional).

Use the Action dropdown box to choose if you would like an alert created

when the device enters the chosen area, exits the area, or both. Use the

Radius box to choose how large the area will be. You can enter values below

a mile as decimals. For example: A half-mile radius geofence would be

entered as .5.

When you’re done, press the Create Geofence button to save.

The Alerts tab will display the most recent Geofence, Speed, Panic, or Power

alerts that have been triggered.

The Video Links tab is not currently active. Future updates will take advantage

of this tab.

Live Tracker will open up a separate window displaying your devices’

locations, and allows you to see past locations. Using the drop-down boxes

on the bottom right of the window, you can adjust how often your screen

refreshes and how many locations will appear on the screen. The counter on

the bottom left of the window displays how long it will be until your screen

refreshes. You can email a link to this page, allowing other users to view

your tracker’s location by click on the Share This icon in the upper right hand

corner of the window. When doing so, you may choose how long the link will

be active before expiring using the Link Expiration dropdown.

Using the Dashboard

The Calendar allows a user to choose from which dates information can

display. Any date that has tracking information will be highlighted. Simply

click on that date to display information. To choose multiple days, click on the

Date Range button, input a start and end date, and press Search. Press the

Current Date button to return to viewing the current day’s information. When

searching by date, all locates generated in the chosen timeframe will display

as breadcrumbs.

Under the Display section you can see a list of all devices currently displaying

information on the map. Click on the View/Change Device button to choose

which of your devices will display on the map. This button only serves a

purpose if there are multiple devices on your account.

Breadcrumb Trail will display all locates, or breadcrumbs, generated on

the date you currently have displayed, connected by a line. Click on any

individual breadcrumb to see detailed information. The BrickHouse shield icon

represents the start and stop of a trip, green circles mean the device was

moving with the arrow indicating direction, and red octagons indicate stops.

Click on the Street View button to open a Google Street View window from

the most recent location of the device. This function will only work if Google

Street View is available in that location.

The Alerts section lets you manage what kinds of alerts

your device will create and how you will be notiﬁed.

Click the Geofence button to manage your geofences. The Geofence Alert

Conﬁguration tab lets you choose when and where alerts will be sent. Select

the device you would like to edit by checking the box next to it.

• Highlight which days you would like to conﬁgure by clicking on each. You

may choose to enter certain hours during which alerts will be active, or

leave these ﬁelds blank to have them sent all the time.

• Choose if duplicate alerts will not be created if the device stays inside or

outside a geofence for a certain period of time using the slider bar.

• Choose what icon will appear where a geofence alert was created using the

Alert Image dropdown box.

• Enter Email Address allows you to choose where alert notiﬁcations will be

sent. Click on the + icon to add phone numbers you want to have texted.

In the Create New Geofence tab you can create geofences around any area

in different shapes. Navigate to the area on the map you would like to create

a geofence. Click on the Circle, Polygon, or Route button. It is suggested that

all geofences be in at least a .2 mile radius, or at least 1 city block around an

area to allow for GPS drift.

To create a circular geofence around an area, click on Circle and then click on the

spot on the map you want to create your geofence around. Hold down the left

mouse button and drag the cursor until your geofence is the size you want, and

release the mouse button.

The Polygon button allows you to create geofences in different shapes. Each point

you click on will be a corner of your perimeter.

A Route geofence will be straight lines. You must choose how far a device will need

to be away from the route before a report is generated.

Once you have created a geofence, assign it a name in the Geofence ﬁeld and hit

Save. You may also choose to enter a short description for your geofence.

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26

BrickHouse Security NANO-XB-REF User manual

BrickHouse Security

Brand: BrickHouse Security

Model: NANO-XB-REF

Type: User manual

Download PDF

Related papers

Other documents