Minka Lavery 4848-276 Installation guide

Brand
Minka Lavery
Model
4848-276
Type
Installation guide

Minka Lavery 4848-276, is a chain hung fixture with intricate crystal adornments. It is crafted from premium materials, ensuring durability and longevity. The fixture comes with all the necessary mounting hardware, making installation quick and effortless. It accommodates multiple light bulbs, allowing you to customize the brightness and ambiance of your space. The fixture is compatible with standard household wiring, simplifying the installation process. Its elegant design makes it a perfect choice for both residential and commercial settings, adding a touch of sophistication to any décor.

Minka Lavery 4848-276, is a chain hung fixture with intricate crystal adornments. It is crafted from premium materials, ensuring durability and longevity. The fixture comes with all the necessary mounting hardware, making installation quick and effortless. It accommodates multiple light bulbs, allowing you to customize the brightness and ambiance of your space. The fixture is compatible with standard household wiring, simplifying the installation process. Its elegant design makes it a perfect choice for both residential and commercial settings, adding a touch of sophistication to any décor.

INSTALLATION INSTRUCTIONS
Item#4848-276 (New. 03/ 22/ 2014)
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig.1
Fig.2
ASSEMBLING THE FIXTURE (Fig.2)
1. Shut off the power at the fuse box or circuit breaker. If
necessary, remove the old fixture including the mounting
hardware.
2. Carefully remove the new fixture from the carton and check
that all parts are included as shown in the illustration.
3. Attach the cap (A) to the fixture body (C) by turning it clock wise
until tight.
4. Hang the long crystal chains (B) to the cap (A).
5. Hang the short crystal chains (D) to the fixture body (C).
6. Attach the acrylic ball (E) to the fixture body(C) by turning it clock
wise until tight.
7. Install the light bulbs (not included) in accordance with the fixture’s
specifications: DO NOT EXCEED THE MAXIMUM WATTAGE
RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!)
HANGING THE FIXTURE (Fig.1)
1. Thread the nipple into the ceiling loop until snug.
2. Thread the other end of nipple with the ceiling loop attached into
the crossbar until snug.
3. Place the lock washer and hex nut over the end of nipple
protruding through crossbar. Then thread the hex nut until tight.
4. Take this crossbar assembly and mount to the ceiling junction box
with the mounting screws (Size: #8-32N*L0.5”). Tighten the
mounting screws securely with a screwdriver. The side of crossbar
marked “GND” must face out.
5. Attach the chain to the fixture loop (A) using quick link. Quick link
must be completely threaded closed when installed.
6. By measuring, determine the correct number of links needed for
the desired hanging height. Using a pair of chain pliers disconnect
and discard the excess chain.
7. Carefully lace the fixture wires through the chain.
8. Slip the lock collar and canopy over the chain.
9. Use the quick link to connect the end link of the chain to the ceiling
loop. Then close the quick link.
10. Feed the fixture wires through the ceiling loop and nipple and pull
until tight.
CONNECTING THE WIRES (Fig.3)
1. At this point, connect the electrical wires as shown in Fig. 3,
making sure that all wire connectors are secured. If your outlet box
has a ground wire (green or bare copper), connect the fixture’s
ground wire to it. Otherwise, connect the fixture’s ground wire
directly to the crossbar using the green screw provided.
2. Tuck these wire connections neatly into the ceiling outlet box and
raise the canopy (G) all the way to the ceiling. Then raise the lock
collar (H) and thread onto the ceiling loop protruding through
canopy.
Your installation is now complete. Return power to the outlet box
and test the fixture.
Fig.3
CHAIN HUNG FIXTURE INSTRUCTION
Notice: It is important to use proper chain pliers (not
included) To OPEN and CLOSE the chain included with this
fixture. Do not open them with other tools that may twist or
stress the chain links. It is important to use proper chain
pliers like the ones shown in the diagram.
CM
USC
lntert ek
White or
HOUSE
Black
WIRES
(Hot)
Smooth
FIXTURE
WIRES
Black or
Ribbed
WIRES
FIXTURE
Bare Copper(Ground)
FIXTURE
WIRES
Copper
(Ground)
HOUSE
(Neutral)
WIRES
White
Bare
Green or
WIRES
HOUSE
Set # A-016
-Crossbar
-Crossbar screw
-mounting screws (2)
  • Page 1 1

Minka Lavery 4848-276 Installation guide

Brand
Minka Lavery
Model
4848-276
Type
Installation guide

Minka Lavery 4848-276, is a chain hung fixture with intricate crystal adornments. It is crafted from premium materials, ensuring durability and longevity. The fixture comes with all the necessary mounting hardware, making installation quick and effortless. It accommodates multiple light bulbs, allowing you to customize the brightness and ambiance of your space. The fixture is compatible with standard household wiring, simplifying the installation process. Its elegant design makes it a perfect choice for both residential and commercial settings, adding a touch of sophistication to any décor.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents