Vinson Acoustics VAC6P Installation guide

Brand
Vinson Acoustics
Model
VAC6P
Type
Installation guide

Vinson Acoustics VAC6P is a high-quality 70V/100V ceiling speaker designed for use in commercial and residential distributed audio systems. With its 6.5" polypropylene cone woofer and 0.5" PEI dome tweeter, it delivers a rich, full-range sound with excellent clarity and dispersion.

The VAC6P features multiple transformer taps, allowing it to be used in a variety of applications. It can handle up to 6 watts of power, making it suitable for both small and medium-sized rooms. The speaker also has a wide frequency response of 50Hz - 20 kHz, ensuring that it can reproduce all types of audio content.

Vinson Acoustics VAC6P is a high-quality 70V/100V ceiling speaker designed for use in commercial and residential distributed audio systems. With its 6.5" polypropylene cone woofer and 0.5" PEI dome tweeter, it delivers a rich, full-range sound with excellent clarity and dispersion.

The VAC6P features multiple transformer taps, allowing it to be used in a variety of applications. It can handle up to 6 watts of power, making it suitable for both small and medium-sized rooms. The speaker also has a wide frequency response of 50Hz - 20 kHz, ensuring that it can reproduce all types of audio content.

VAC6P In-Ceiling/In-Wall Installation Instructions
If you are not familiar with a 70V/100V Distributed Audio System, we would highly recommend that you
contact a trained professional to do the installation.
Safety Instructions:
- Read all instructions
- Keep these instructions
- Be aware of all warnings and safety precautions
- Do not use this product in or near water or other liquids
- Do not use any aerosol cleaner or disinfectant on this product
- Ensure that the installation hole size is cut accurately
- When cutting your installation hole, ensure that you are free and clear of all electrical wire and
plumbing pipes
- When daisy-chaining speakers, ensure that the sum of the tapped wattage of all speakers in the
chain do not exceed 80% of the maximum output wattage of the connected amplifier channel
- Verify that your installation complies with all local codes
Specifications:
VAC6P
Specifications
Transducer:
6.5" Polypropylene Cone w/ Rubber Surround
0.5" Pivoting PEI Dome Tweeter
Power Rating:
6W RMS
Transformer Taps:
70V: .75W, 1.5W, 3W, 6W
100V: 1.5W, 3W, 6W N/C
Impedance:
8Ω
Frequency Range:
50Hz - 20 kHz
Sensitivity:
88 dB @ 1w/1m
Coverage:
110° Conical
Surface Preparation
1. Use the supplied template to mark your installation hole in the proper ceiling or wall location.
Carefully, cut out the installation hole.
2. For unfinished ceilings and walls, a new constructions bracket (VAGIC6NCB; sold separately), is
needed to be installed prior to the drywall being installed. Attach the new construction bracket, ensuring
that the hole of the bracket is in the desired location.
Wiring Installation
1. Run the wire (18-14-guage) from the amplifier location to the cutout. Allow for an extra foot of wire
at the cutout.
2. To attach the speaker to your amplifier, connect the output of the amplifier to the “Com” (black)
wire of the speaker tap. Connect the
of the amplifier to the colored cable of the speaker tap that
represents the desired speaker wattage.
1. To daisy chain speakers, connect the two speaker tap wires from step 2, to the same speaker tap wires on
the next speaker in the chain. Repeat for each additional speaker.
Speaker Installation
1. Slide the speaker into the cutout as shown.
2. Using a Phillips head screwdriver, tighten all 3 screws until they are all secure.
Important: Do not over tighten the screws.
3. Attach the magnetic grill to the speaker.
In-Ceiling Installation
  • Page 1 1
  • Page 2 2

Vinson Acoustics VAC6P Installation guide

Brand
Vinson Acoustics
Model
VAC6P
Type
Installation guide

Vinson Acoustics VAC6P is a high-quality 70V/100V ceiling speaker designed for use in commercial and residential distributed audio systems. With its 6.5" polypropylene cone woofer and 0.5" PEI dome tweeter, it delivers a rich, full-range sound with excellent clarity and dispersion.

The VAC6P features multiple transformer taps, allowing it to be used in a variety of applications. It can handle up to 6 watts of power, making it suitable for both small and medium-sized rooms. The speaker also has a wide frequency response of 50Hz - 20 kHz, ensuring that it can reproduce all types of audio content.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents