Page is loading ...
ADVANCED ENGINE MANAGEMENT INC.
2205 126
TH
Street, Unit A Hawthorne, CA. 90250
Phone: (310) 484-2322 Fax: (310) 484-0152
www.aempower.com
Instruction Part Number: 10-7010
2000-2003 Mitsubishi Eclipse RS & GS 4G64 C.A.R.B. E.O. #D-392-21
2004 Mitsubishi Eclipse RS & GS 4G64 C.A.R.B. E.O. #D-392-28
© 2009 Advanced Engine Management, Inc.
Installation Instructions for:
Part Number 22-433
2000-2004 Mitsubishi Eclipse RS & GS
SHORT RAM
INTAKE
SYSTEM
Manual Trans Only
Congratulations! You have just purchased the finest Air Induction & Filtration system for your car at
hort Ram Air Intake System is the result of extensive development on a wide variety of
ly
th
any price!
The AEM S
cars. It is the most advanced short pipe air intake system on the market. Each system is specifical
engineered for its particular application. All AEM Short Ram Air Intake Systems deliver maximum
performance gains through lightweight, all-aluminum, mandrel-bent tubing that is tuned in both leng
and diameter. The aluminum will not crack in extended use like plastic. The tube length and
diameter are matched for each specific engine to give power over a broad RPM range. Unlike plastic
systems that use a continually diverging cross-section, we take advantage of the acoustical energy in
the inlet duct to promote cylinder filling during the intake valve opening event. Every intake is coated
with a high-gloss, heat-reducing Zirconia based powder coating. This special blend of powder
coating helps reduce heat penetration, which in turn reduces the temperature of the inlet air charge.
The cooler inlet air temperature translates to more power during the combustion process because
cool air is denser than warm air. The air mass flow to the engine is increased because of the
increased airflow and reduced inlet temperature, which translates to more power.
ill of Materials for: 22-433 B
Quanity Part Number Description
1 21-202D Air F Dryilter 2.75”X5"
1 2-4331 Inlet Pipe
1 32-3030 Bracket
1 2-606 Inlet Pipe to MAF Sensor Adaptor
1 1 228599 Soft Mount
5 4 44.460.04 6mm Nut
2 559999 6mm x 25 Washer mm x 1mm
1 30217-32 2.75" Rubber 90 Deg. Elbow
1 5-253 Hose,Adapter 2.50/3.0"X3"AEM
1 9452 #52 Hose Clamp
3 9444 #44 Hose Clamp
1 9448 #48 Hose Clamp
4 1 M6 x 1.00 x 30mm Socket Bolt -2020
1 1-2030 Hex Flange Bolt, M6 X 1 X 16
1 10-7010 Instructions
6 3/8.5" 65128 " Rubber Hose
2 4093-5 Hose Clamp, ¾”
2 10-922S AEM Decal
Read and understand these instructions BEFORE attempting to install this product.
le is parked on a level surface.
attery terminals.
urs let it cool down.
1) Getting started
a) Make sure vehic
b) Set parking brake.
c) Disconnect both b
d) If engine has run within the past two ho
2) Removing the stock air inlet system
U
pp
er clam
p
Breather hose
a) Stock intake system. b) Pull breather hose off of valve cover. Loosen the
upper and lower hose clamps on the stock inlet tube.
c) Unplug the MAF sensor. Remove stock inlet pipe. d) Loosen the four nuts that hold the MAF sensor to the
Release four clamps on the air box and remove upper
air box from the vehicle.
airbox. Carefully set aside the MAF sensor.
e) Release air snorkel by first pressing in the centers of f) Loosen the three bolts holding down the air box.
the plastic rivets. Remove air box and snorkel from vehicle.
g) Remove lower mounting bracket. h) Loosen the three bolts that hold in the lower air box
and remove it from the vehicle.
3) Installation of the AEM Short Ram Intake System
ely tighten the hose clamps or mounting tab hardware
When installing the Short Ram Intake System, DO NOT complet
until instructed to do so later in these instructions.
b) Attach rubber reducer to MAF sensor using the size
Size 52 clamp
a) Attach MAF adapter to MAF sensor using the
supplied bolts and lock nuts. 52 hose clamp.
c) Place rubber elbow with two hose clamps onto the
rottle body. The long end attaches to the throttle body.
d) Insert upper SRS pipe into rubber elbow. Attach
support bracket to engine using the supplied bolt and th
washer. Place aluminum tab behind the plastic tab.
e) Install the supplied breather hose as shown. Secure
oth ends with supplied ¾” hose clamps.
f) Install rubber mount in threaded hole as shown.
b
g) Install the air filter to the MAF sensor adapter.
ighten the air filter hose clamp.
h) Install MAF sensor to pipe using the proper hose
clamp. Attach support bracket as shown. Do not T
completely tighten the lock nut. Plug in MAF sensor.
See next step for proper installation.
j
) AEM Short Ram System installed.
Lock Nut
Fender Washer
e Support
Rubber Mount
Inlet Pip
Tab
C
h
ass
i
s
i) Proper installation of the rubber mount.
4) Reassemble the vehicle
ls and check that all fasteners that were moved or removed are properly
r.
For Technical Inquiries
a) Inspect the engine bay for any loose too
tightened, including the fender line
b) Position the pipes so that they do not touch any other surfaces and tighten all hose clamps, nuts and bolts.
c) Reconnect battery terminals.
d) Start engine and perform a final inspection before driving the vehicle.
E-Mail Us At
/
