Astria Fireplaces BRT40 Instruction Sheet

Brand: Astria Fireplaces

Model: BRT40

Category: Car kits

Type: Instruction Sheet

This manual is also suitable for

CRAFTSMAN

Astria Fireplaces BRT40 is designed to conveniently heat your room using cutting-edge technology and premium materials. This free-standing fireplace features a contemporary design that complements various room decors. Enjoy customized warmth with its adjustable flame height and temperature settings, easily managed with the included remote control.

The BRT40 boasts a realistic log set and ember bed, creating an ambiance similar to a real wood-burning fireplace. It also incorporates innovative safety features for peace of mind, including overheating protection and automatic shut-off.

BL SERIES REFRACTORY FIREBOX LINER KITS

[FOR USE WITH MODELS: CRAFTSMAN36/42, BRT4536/42, BRT4336/42, BRT4036]

FIREBOX LINER KITS

32/36/42 FIREPLACES

P/N 127154-01

Rev. B, 03/2017

HEARTH PRODUCTS

KITS AND ACCESSORIES

GENERAL INFORMATION

Attractive refractory ﬁ rebox liner kits are available in various styles.

READ ALL THE STEPS BEFORE STARTING THE INSTALLATION

THE FIREPLACE MUST BE OFF AND COLD BEFORE BEGINNING.

ALL WARNINGS, PRECAUTIONS AND INSTRUCTIONS IN THE

INSTALLATION AND OPERATION MANUAL PROVIDED WITH THE

APPLIANCE APPLY TO THESE INSTRUCTIONS.

If you encounter any problems, need clariﬁ cation of these instructions

or are not qualiﬁ ed to properly install this kit, contact you local

distributor or dealer.

If any of these parts are missing or damaged, contact your dealer or

IHP.us.com for referral information.

KIT CONTENTS

1 ea. Left Refractory Panel

1 ea. Right Refractory Panel

1 ea. Bottom Refractory Panel

1 ea. Rear Refractory Panel

1 ea. Instruction Sheet

Cat. No. Model Description

F1058 BL32S 32” White Stacked Refractory Brick Liner Kit

F1059 BL36 36” Textured Refractory Brick Liner Kit

F1060 BL36H 36” Textured Refractory Herringbone Brick Liner Kit

F1061 BL42 42” Textured Refractory Brick Liner Kit

F1062 BL42H 42” Textured Refractory Herringbone Brick Liner Kit

CAUTION: Turn off the gas supply, disconnect

the electric circuit and allow the appliance to fully

cool down before performing this installation.

Glass and refractory panels may be heavy for some

individuals. If this is the case, please request help

from someone else.

Figure 1 - Removing Glass Doors

Spring Clip (Press

Spring Clip To

Release Pivot Pin)

Remove Bottom

Pin From Pivot

Plate While

Sliding Door Out

Of The Upper

Track

Fold Bi-Fold

Door After

Releasing Spring

Clip and Slide

Door Out of

Upper Track

Pivot Pin

Pivot Plate

ACCESSING FIREBOX

All Models

1. Remove both glass door panels (when equipped) by following

the instructions shown in Figure 1.

2. Remove 2 screws retaining the screen assemblies and slide

screen rods out of mounting holes located behind facial open-

ing (see Figure 2).

3. Remove any hearth treatments (volcanic stone, pan material or

embers) from around burner pan.

4. Remove front brick access panel by lifting and angling out of

ﬁ replace opening (see Figure 2).

5. On exposed installations, further access to control compartment

may be gained by removing lower panel from facial opening.

Remove panel by carefully pulling with your ﬁ ngertips in louver

openings (when equipped) or, on smooth panels by pushing

out from inside ﬁ replace until panel snaps free.

IHP.us.com 127154-01A2

Figure 2 - Accessing Control Compartment

Brick Access Panel

Lower

Panel

Control

Access

Cover

Screen

ssembly

Figure 3 - Disconnecting Pilot Leads

REMOVING LOGS AND BURNER PAN ASSEMBLIES

1. Remove logs and grate by lifting individually off burner pan

assembly. Place them safely away from your work area.

2. Disconnect the 7/16" pilot line ﬁ tting and remove 2 thermopile

leads connected to terminals marked TP/TH and TP on control

valve (see Figure 3).

3. Disconnect igniter lead wire connected at rear of piezo igni-

tion device or at terminal marked IGN on module (electronic

models) (see Figure 3).

4. Remove top screw on burner inlet shield. Remove burner

inlet shield to expose burner and ﬂ ex line ﬁ ttings (see Figure

4, Page 3).

5. Disconnect the 3/8" ﬂ are ﬁ tting on ﬂ ex line using a 3/4" open

end wrench on both the burner ﬁ tting and ﬂ are ﬁ tting (see

Figure 4, Page 3).

Igniter Lead

(Millivolt

Models)

Igniter Lead

(Electronic Models)

Thermopile Lead

Pilot Tube

Fitting

1. Remove 4 Phillips head screws located on valve bracket and lift

retaining ﬂ ange off burner pan (see Figure 5, Page 3).

2. Lift burner pan and draw pilot leads out through knockout pass

on ﬁ rebox(see Figure 5, Page 3).

NOTE: Use a free hand to guide the leads around ﬁ rebox from

inside control compartment. Be careful not to bend, kink or

damage leads.

Figure 4 - Disconnecting Gas Flex Line Fitting

Figure 5 - Removing Burner Pan

Burner Inlet Shield

Flexline

Flare

Fitting

Burner

Fitting

Pilot

Leads

4 Screws Holding

Valve Bracket

Retaining

Flange

Burner Pan

IHP.us.com

127154-01A 3

Figure 6 - Removing Panel Extenders

Figure 7 - Removing Side Brick Panels (Full Replacement)

REMOVING OLD REFRACTORY

1. If adding side brick refractory, you must remove and discard the

2 panel extenders located on either side of the smoke deﬂ ec-

tor. If this is a full brick replacement you also need to replace

the bottom rear hearth brick in addition to the side panels (see

Figure 6).

2. Remove 2 hex screws holding side brick retainers located near

top of ﬁ rebox on each side. Retain screws and brackets for later

reinstallation (see Figure 7).

3. Remove side refractory panels (if applicable) by angling out one

side panel ﬁ rst, followed by rear panel, and then remaining side

panel. This will prevent rear panel from dropping and possibly

causing injury (see Figure 7).

Panel Extender

Bottom Rear

Hearth Brick

Smoke

Deﬂector

4 Retainer

Screws

Side Brick Retainers

UNPACKING NEW REFRACTORY

1. Open both ends of carton, split lengthwise and spread carton

out near your work area.

2. Arrange panels on top of packing and identify each piece in

order of assembly (see Figure 8).

3. Check all items for any shipping damage. If damaged, contact

your authorized dealer of this product. If the dealer can’t supply

original replacement part(s), contact IHP.us.com for referral

information. Be sure to have your kit model number and part

number ready when you call.

4. Refer to parts list on chart below for reference.

Left Side

Brick Panel

Rear Brick

Panel

Right Side

Brick Panel

Front and Rear

Hearth Bricks

Figure 8 - Identifying Refractory

IHP.us.com 127154-01A4

INSTALLING NEW REFRACTORY

1. Locate oval knockout pattern at bottom of right side brick panel.

2. Place end of a 1" diameter wood dowel or metal pipe inside

knockout area and punch out entire 1" x 1-1/2" slotted area

(see Figure 9).

NOTE: Clean bottom hearth pan of all debris before installing

bottom hearth brick to prevent obstruction. To insure a proper

ﬁ t of burner pan and valve bracket, there must be 3/8" of clear-

ance from back edge of control access opening and leading

edge of rear hearth brick.

3. Reinstall refractory panels in reverse order starting with bottom

rear hearth brick, then rear panel and then both side panels.

4. Replace 2 side brick retainers using 4 hex screws removed

previously.

Figure 9 - Removing Knockout

Figure 10 - Reconnecting Pilot Leads

REINSTALLING BURNER PAN ASSEMBLY

1. Pull gas ﬂ ex line back through knockout hole in ﬁ rebox.

2. Replace burner pan assembly, while feeding pilot leads back

through knockout. With your free hand, carefully guide lines

around outer ﬁ rebox and into control compartment.

3. Place retaining ﬂ ange on valve bracket back over leading edge

of burner pan (see Figure 5, Page 3).

4. Center pan to valve bracket and replace 4 pan head screws

into valve bracket mounting locations (see Figure 5, Page 3).

5. Hand thread pilot line ﬁ tting into control valve outlet and tighten

using a 7/16" open end wrench (see Figure 10).

Igniter Lead

Red (TP)

White (TP/TH)

Piezo

Ignitor

Control Valve

Pilot

Fitting

1. Reconnect RED thermopile lead to terminal marked TP and

WHITE thermopile lead to terminal marked TP/TH (see Figure 10).

2. Reconnect igniter lead at back of piezo igniter (millivolt models)

or on control module terminal marked IGN (electronic models).

3. Thread 3/8" ﬂ ex line ﬁ tting onto burner ﬂ are ﬁ tting. Tighten us-

ing a 3/4" open end or adjustable wrench. Make certain burner

does not spin or misalign, burner tubes should have main gas

port holes facing down into pan.

4. Reattach burner inlet shield with screw in top hole of burner

bracket (see Figure 4, Page 3).

5. Restore power and gas to unit. Follow the safety and lighting

instructions found on the appliance information tag to check for

gas leaks and proper pilot and main burner operation.

IHP.us.com

127154-01A 5

Figure 11 - Adding Pan Material

1. Replace vermiculite material back in burner pan and smooth

to height and grade of pan edges. Reapply ember material and

replace grate into pan notches. Leave a minimum of 1/2" air gap

under grate bars. See Figure 11.

2. Reassemble logs onto grate, beginning with rear base log. See

Pages 6 and 7 for various model log placement.

3. Reinstall right ﬁ replace screen assembly by inserting end rod

into uppermost mounting hole in right screen pocket. Screw

mounting lug into left most pilot hole behind and towards center

of upper facing. Repeat for left assembly using mounting lug to

the right of center. Screen rods should overlap at middle and

readily conceal into side screen pockets.

1. Replace the control access cover and front brick access panel.

2. Reapply any volcanic stone treatments to hearth ﬂ oor. DO NOT

PLACE VOLCANIC STONE IN THE BURNER PAN OR NEAR THE

BURNER INLET SHIELD AREA.

3. Replace the glass doors (if equipped) by following the instruc-

tions shown in Figure 1, Page 2, in reverse order.

If any components are found damaged, contact an authorized dealer

for original IHP replacement part(s) or IHP.us.com for referral in-

formation.

REPLACEMENT PART NUMBERS

KIT MODEL Left Side Brick Panel Right Side Brick Panel Rear Brick Panel Rear Hearth Brick Front Hearth Brick

BL32S (F1058) J4209 J4205 J4201 J4195 J4198

BL36 (F1059) J3954 J3959 J3964 J3969 J3971

BL36H (F1060) J4127 J4130 J4133 J4136 J4138

BL42 (F1061) J4062 J4067 J4072 J4077 J4079

BL42H (F1062) J4140 J4143 J4146 J4149 J4151

CAUTION: Be sure to inspect the components

and wiring for damage before restoring power

to the unit. Leak check all gas lines, especially

at connection points, using noncorrosive leak

detection fluid. NEVER CHECK FOR LEAKS WITH

AN OPEN FLAME. Tighten all connects if neces-

sary. Follow the lighting instructions found on

the information tag and check for proper ignition

and operation.

1/2”(13 mm)

IHP.us.com 127154-01A6

MODELS

BRT2032TMN

BRT2032TEN

MODELS

BRT2332TMN

BRT2332TEN

BRT2532TMN

BRT2532TEN

LOG PLACEMENT

IHP.us.com

127154-01A 7

MODELS

BRT4036TMN(-B)

BRT4036TMP(-B)

BRT4036TEN(-B)

BRT4036TEP(-B)

BRT4336TMN(-B)

BRT4336TMP(-B)

BRT4336TEN(-B)

BRT4336TEP(-B)

BRT4536TMN(-B)

BRT4536TMP(-B)

BRT4536TEN(-B)

BRT4536TEP(-B)

MISSION36TMN

MISSION36TEN

MODELS

BRT4042TMN(-B)

BRT4042TMP(-B)

BRT4042TEN(-B)

BRT4042TEP(-B)

BRT4342TMN(-B)

BRT4342TMP(-B)

BRT4342TEN(-B)

BRT4342TEP(-B)

BRT4542TMN(-B)

BRT4542TMP(-B)

BRT4542TEN(-B)

BRT4542TEP(-B)

MISSION42TMN

MISSION42TEN

LOG PLACEMENT

P/N 127154-01 Rev. B 03/2017

IHP reserves the right to make changes at any time, without notice, in design, materials, speciﬁ ca-

tions, prices and also to discontinue colors, styles and products. Consult your local distributor

for ﬁ replace code information.

1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210

Astria Fireplaces BRT40 Instruction Sheet

Brand: Astria Fireplaces

Model: BRT40

Category: Car kits

Type: Instruction Sheet

This manual is also suitable for

CRAFTSMAN

Download PDF

report

Astria Fireplaces BRT40 Instruction Sheet

This manual is also suitable for

Astria Fireplaces BRT40 Instruction Sheet

Related papers

Other documents