Astria Fireplaces Plantation Instruction Sheet

Brand: Astria Fireplaces

Model: Plantation

Type: Instruction Sheet

REQUIRED TOOLS AND SUPPLIES

1/8" Shims

Phillips Screwdriver

GENERAL INFORMATION

Bi-Fold glass doors are available in ebony, pewter and bronze

ﬁ nishes.

READ ALL THE STEPS BEFORE STARTING THE INSTALLATION

THE FIREPLACE MUST BE OFF AND COLD BEFORE BEGINNING.

ALL WARNINGS, PRECAUTIONS AND INSTRUCTIONS IN THE

INSTALLATION AND OPERATION MANUAL PROVIDED WITH THE

APPLIANCE APPLY TO THESE INSTRUCTIONS.

If you encounter any problems, need clariﬁ cation of these instructions

or are not qualiﬁ ed to properly install this kit, contact you local

distributor or dealer.

If any of these parts are missing or damaged, contact your dealer or

IHP.us.com for referral information.

DOOR RAIL AND HARDWARE INSTALLATION

IMPORTANT: Install top and bottom rails and hardware before

installing glass door panels.

1. Remove screws securing top face to ﬁ rebox (see Figure 1).

2. Align holes on rail to be installed at top and replace screws. Note:

Door rails are identical until spring clips are in place.

3. Using remaining door rail as a template, place along front row

of bricks at bottom making sure rail front surface is ﬂ ush with

ﬁ replace bottom face surface. Mark hole centers and remove rail

(see Figure 1).

4. Drill 9 - 5/32" diameter holes about 1" deep directly into bricks

using a 5/32" concrete drill bit (not provided).

5. Place rail back on bricks and align holes. Secure using 9 concrete

screws provided with glass door kit.

6. Secure retaining clips to top and bottom rails (see Figure 2).

Top Rail Remove Screws

then Replace to

Secure Top Rail

Bottom Rail (Use as a

Template before Drilling

Drill Holes

into Bricks Concrete Screws

Figure 2 - Mounting Door Retaining Clips

Figure 1 - Securing Door Rails to Fireplace

Top Rail

Bottom Rail

Retaining

Clip

BDMO48 SERIES GLASS BI-FOLD DOOR KITS

[FOR USE WITH MODEL PLANTATION 48]

BDMO48 SERIES GLASS BI-FOLD DOOR KITS

PLANTATION™ 48 FIREPLACES

P/N 127145-01

Rev. B, 03/2017

HEARTH PRODUCTS

KITS AND ACCESSORIES

127145-01B 1

IHP.us.com

KIT CONTENTS

1 ea. Glass Bi-Fold Doors

1 ea. Instruction Sheet

Cat. No. Model Description

F1017 BDMO48EA 48" Masonry Ceramic Glass Bi-Fold Door, Ebony

F1018 BDMO48GA 48" Masonry Ceramic Glass Bi-Fold Door, Pewter

F1019 BDMO48CA 48" Masonry Ceramic Glass Bi-Fold Door, Bronze

CARE AND OPERATING GUIDELINES

• Glass doors should be operated in the fully open positions only.

• When operating doors, do not slam shut or abuse them.

• Always keep below bottom edge of doors clear from obstacles

or debris.

• Do not operate this appliance if glass doors are broken or dam-

aged.

• Do not use abrasive liquids or cleaners for cleaning of glass and

door trims. Any household glass cleaner should sufﬁ ce.

• Do not clean doors when hot, allow appliance to cool before

cleaning.

Figure 4 - Adjusting Glass Door

Figure 3 - Installing Glass Doors

Bottom

Retaining Clip

Side Top

Pin into Top

Retaining

Clip

Spring Clip

Side Front

Face

Partially

Opened Door

DOOR ADJUSTMENT

Remove doors and slightly loosen upper spring clips. Replace and

fully close doors. Use 1/8" shims (any material) to level doors. Once

proper setting is achieved, carefully open doors enough to access

top retaining clips with a phillips screwdriver. Tighten screws. See

Figure 4.

P/N 127145-01 Rev. B 03/2017

IHP reserves the right to make changes at any time, without notice, in design, materials, speciﬁ ca-

tions, prices and also to discontinue colors, styles and products. Consult your local distributor

for ﬁ replace code information.

1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210

INSTALLING GLASS DOORS

After spring clips have been installed some adjustments may be

needed. Install the doors using the following steps:

1. With bi-fold doors completely folded, insert bottom pivot pin into

bottom retaining clip located at far left and far right side of bottom

rail. Swing door to vertical position making sure top pins slide into

top door rail. Door is installed when top door pin snaps into spring

clip (see Figure 3, Page 2).

2. Repeat step 1 for remaining door.

If you ﬁ nd the doors do not close properly or do not appear level

or straight, proceed with section on door adjustment on Page 2.

Astria Fireplaces Plantation Instruction Sheet

Astria Fireplaces Plantation Instruction Sheet

Astria Fireplaces Plantation Instruction Sheet

Related papers

Other documents