OTC 6471 Operating instructions

  • Hello! I've reviewed the provided operating instructions for the OTC Camshaft Sensor Synchronizer Tool 6471. This document outlines the steps for proper installation and use of the tool, specifically for Ford 3.0L V6 engines. It emphasizes the importance of correctly aligning the camshaft sensor. I'm ready to answer any questions you might have about the tool and its usage.
  • What is the application of the tool?
    What should I do before removing the camshaft sensor housing?
    What is the first step in using the tool?
    What is the tool number?
    What Ford tool number this tool is equivalent to?
Form No. 107095
Form No. 107095
Operating Instructions for: 6471
(511538)
Operating Instructions for: 6471
(511538)
655 Eisenhower Drive
Owatonna, MN 55060 USA
Phone: (507) 455-7000
Tech. Serv.: (800) 533-6127
Fax: (800) 955-8329
Order Entry: (800) 533-6127
Fax: (800) 283-8665
International Sales: (507) 455-7290
Fax: (507) 455-7063
Website: www.otctools.com
655 Eisenhower Drive
Owatonna, MN 55060 USA
Phone: (507) 455-7000
Tech. Serv.: (800) 533-6127
Fax: (800) 955-8329
Order Entry: (800) 533-6127
Fax: (800) 283-8665
International Sales: (507) 455-7290
Fax: (507) 455-7063
Website: www.otctools.com
Rev. C, January 19, 2015
© Bosch Automotive Service Solutions Inc.
Rev. C, January 19, 2015
© Bosch Automotive Service Solutions Inc.
Ford Camshaft Sensor Synchronizer Tool
Application: 1993 – 1995 3.0L V6 Ford Taurus/Mercury Sable
Ford Camshaft Sensor Synchronizer Tool
Application: 1993 – 1995 3.0L V6 Ford Taurus/Mercury Sable
CAUTION: Before removing the camshaft sensor housing assembly, note
the position of the camshaft sensor electrical connector. The connector
MUST be reassembled in the same position during installation.
1. Rotate crankshaft to set No. 1 cylinder at top dead center of compression
stroke.
2. Engage camshaft sensor housing vane in slot of tool No. 6471 (511538).
3. Rotate tool on camshaft sensor housing until tool engages housing notch.
(Tool should be square and in contact with entire top of housing.)
4. Install camshaft sensor housing and tool assembly into engine according
to instructions in the vehicle service manual. Torque fasteners to factory
specications.
CAUTION: Before removing the camshaft sensor housing assembly, note
the position of the camshaft sensor electrical connector. The connector
MUST be reassembled in the same position during installation.
1. Rotate crankshaft to set No. 1 cylinder at top dead center of compression
stroke.
2. Engage camshaft sensor housing vane in slot of tool No. 6471 (511538).
3. Rotate tool on camshaft sensor housing until tool engages housing notch.
(Tool should be square and in contact with entire top of housing.)
4. Install camshaft sensor housing and tool assembly into engine according
to instructions in the vehicle service manual. Torque fasteners to factory
specications.
WARNING: Wear eye
protection that meets ANSI
Z87.1 and OSHA standards.
WARNING: Wear eye
protection that meets ANSI
Z87.1 and OSHA standards.
Camshaft
Sensor
Housing
Camshaft
Sensor
Housing
No. 6471
(511538)
No. 6471
(511538)
Note: Same as Ford No. 303-453 (T93P-12200-A).
Note: Same as Ford No. 303-453 (T93P-12200-A).
/