2. OTC
  3. 6480

OTC 6480 Operating instructions

  • Hello! I've reviewed the provided operating instructions for the OTC 6480 Ford Camshaft Holding Tool Adapter and the 6481 Camshaft Holding Tool. This document outlines how to properly use these tools to service the timing chain on several Ford vehicles. I understand the document recommends wearing eye protection that meets ANSI Z87.1 and OSHA standards. I'm ready to answer your questions about their usage or any other content in the document.
  • What is tool No. 6480 used for?
    What is tool No. 6481 used for?
    Which Ford vehicle engines are these tools applicable for?
    What should I do before using these tools?
Form No. 107104
Operating Instructions
for: 6480
(511548)
655 Eisenhower Drive
Owatonna, MN 55060 USA
Phone: (507) 455-7000
Tech. Serv.: (800) 533-6127
Fax: (800) 955-8329
Order Entry: (800) 533-6127
Fax: (800) 283-8665
International Sales: (507) 455-7290
Fax: (507) 455-7063
© Bosch Automotive Service Solutions LLC
July 25, 2014 Rev. C
Ford Camshaft Holding Tool Adapter
Application: 1997 – 2011 4.0L SOHC Explorer (V6), Mountaineer (V6), Ranger (VIN E)
1997 – 2008 4.0L SOHC Explorer, Mountaineer, Ranger (VIN X)
2005 – 2010 4.0L SOHC Mustang (VIN N)
1. Install tool Nos. 6480 (511548) and 6481 (511549) on the
camshaft as shown.
2. Secure tool No. 6481 (511549) to the cylinder head.
3. Service the timing chain as required according to instructions
in the vehicle service manual.
4. Torquefastenerstofactoryspecications.
WARNING: Wear eye protection that
meets ANSI Z87.1 and OSHA standards.
No. 6481
(511549)
No. 6480
(511548)
NOTE:
• Same as Ford No. 303-576 (T97T-6256-D).
• This tool is used with No. 6481 (511549) Ford Camshaft
Holding Tool.
Form No. 107104
Operating Instructions
for: 6480
(511548)
655 Eisenhower Drive
Owatonna, MN 55060 USA
Phone: (507) 455-7000
Tech. Serv.: (800) 533-6127
Fax: (800) 955-8329
Order Entry: (800) 533-6127
Fax: (800) 283-8665
International Sales: (507) 455-7290
Fax: (507) 455-7063
© Bosch Automotive Service Solutions LLC
July 25, 2014 Rev. C
Ford Camshaft Holding Tool Adapter
Application: 1997 – 2011 4.0L SOHC Explorer (V6), Mountaineer (V6), Ranger (VIN E)
1997 – 2008 4.0L SOHC Explorer, Mountaineer, Ranger (VIN X)
2005 – 2010 4.0L SOHC Mustang (VIN N)
1. Install tool Nos. 6480 (511548) and 6481 (511549) on the
camshaft as shown.
2. Secure tool No. 6481 (511549) to the cylinder head.
3. Service the timing chain as required according to instructions
in the vehicle service manual.
4. Torquefastenerstofactoryspecications.
WARNING: Wear eye protection that
meets ANSI Z87.1 and OSHA standards.
No. 6481
(511549)
No. 6480
(511548)
NOTE:
• Same as Ford No. 303-576 (T97T-6256-D).
• This tool is used with No. 6481 (511549) Ford Camshaft
Holding Tool.
/