Redring RM1 Powerstream Shower Mixer Kit User manual

Brand: Redring

Model: RM1 Powerstream Shower Mixer Kit

Category: Sanitary ware

Type: User manual

A4 Leaflet 579-2379-20b

There are 3 defined spray plate settings adjustable by rotating the spray plate .

The modeshave a positive “click” to identify them (see diagrams)

WARNING: YOU MUST REGULARLY INSPECT THE SHOWER HOSE

FOR WEAR AND DAMAGE. REPLACE IF NECESSARY,

OR EVERY TWO YEARS, WITH OUR APPROVED PART.

WARNING: IN ORDER TO MAINTAIN THE PERFORMANCE OF YOUR SHOWER,

YOU MUST CLEAN THE SHOWER HEADSET REGULARLY

All water contains particles of lime-scale, which build up in the shower headset

and unit reducing the performance.

It is therefore important to clean the shower headset bysimply rubbing the rubber nozzles,

or soaking in proprietary lime-

scale remover and rinsing thoroughly before use.

In some winter conditions, when the incoming mains water is particularly cold

it may be necessary to select the inner or outer spray pattern only,

this will ensure correct operation of the shower with a slightly lower water flow rate.

Note:

After use it is normal for some water to drip from the shower handset for a

few moments. This inhibits lime-scale build-up over prolonged use.

Additional Accessories (Can be supplied against any Credit or Debit cards, ring 08744 372 7750

)

Chrome 1.25m long Shower Hose Cat No. 93-797641 White 2m long Shower Hose Cat No. 83-595308

Standard White/Chrome Accessory Kit Cat No. 83-595302 Chrome 2m long Shower Hose Cat No. 83-595310

Premium White/Chrome Accessory Kit Cat No. 83-595303 White 1m long Riser Rail Cat No. 83-595311

Curtain and Rail Pack with Non-Slip Mat Cat No. 83-792801 Chrome 1m long Riser Rail Cat No. 83-595312

Curtain and Rail Pack Cat No. 83-792802

APPLIED ENERGY PRODUCTS LIMITED MORLEY WAY, PETERBOROUGH PE2 9JJ

TEL: +44 (0) 844 372 7761 / FAX: +44 (0) 844 372 7762

Website: www-applied-energy.com

SHOWER MIXER

HANDBOOK

(FOR USE WITH THE

REDRING POWERSTREAM)

IMPORTANT:

This booklet should be left with the user

after installation and demonstration

A. For Shower Cabinets and

Recessed Installations

Shower tailpipes can be passed

through cabinet wall in order to

make plumbing connection using

standard tap connectors.

Powerstream Shower Accessories

Schematic Installation Diagram showing Powerstream serving Shower and Basin

IMPORTANT NOTES

1. The HOT supply from the Powerstream MUST be connected to the red “turn on fully” control valve.

2. Please see the Powerstream handbook for full details of installation.

Setting the Outlet Water Temperature

Adjusting the service valve

Turn the service on, then-

•If the unit is to supply a basin.

Ø Turn on the hot water tap at the basin.

Ø Adjust the service valve until the water comes out of the tap at the required temperature.

Ø Check that the unit works correctly when the basin tap is closed and then opened again,

if not, adjust the service valve slightly

•If the unit is to supply a shower.

Ø Turn the service valve anti-clockwise until the neon light goes out,

and then turn it back until the neon light just comes on.

Ø Check the water temperature of the handset and if necessary, turn the cold tap on and adjust to get the desired

shower temperature.

Ø Explain to the user that when he unit is used, the hot water should be turned on fully so that the water temperature is

always the same.

•Please refer to the Powerstream handbook for FULL details of operation and installation of the Powerstream.

IMPORTANT: Demonstrate the unit to the user and give them this guide

B. For Surface Mounting

Position adaptor to suit or

discard if not required.

Bind tailpipes with P.T.F.E. tape

if necessary.

Screw on and orientate wall plate

elbows to suit incoming pipework.

Screw shower to surface of wall

using screw and wallplugs

provided.

Make plumbing connection.

Shower Mixer Valve User Instructions

Shower operation

• Check that the power is switched on at the mains isolator switch.

• Turn on the hot or “flow” tap fully (see diagram 1).

• If the unit has been used recently, run the water through for a f

ew seconds to let the temperature settle down.

You may get a short burst of very hot water front the unit.

• Turn on the cold or “temperature” tap, if necessary, to adjust the temperature of the water.

• Make sure that no other outlets connected to the unit are used whilst you are in the shower, or the water flow

will drop suddenly.

• When you havefinished DO NOT switch off the power if you are going to use the unit again shortly.

• It is important to clean the shower headset regularly (see page 4)

• If the shower headset can reach the water in the shower tray, bath or basin, the shower hose should be fitted through

the hose-retaining loop on the soap tray. This will comply with thewater by -laws.

Knob “A” “Turn on fully” hot water only.

This tap must be FULLY OPEN.

Knob “B” “Temperature control” tap used to bleed cold water

to give blended outlet temperature.

Note Knob “A” and Knob “B” MUST be switched off/closed

when finished showering.

What to do if things go wrong

Self Help

Symptom Cause What to do

Little or no water flows The main water supply is turned off Turn on the main supply valve at the stop valve

Cold water only – neon light off

The main water supply is not turned

on enough Turn on main supply fully at the stop valve

Cold water only – neon light on

The water flow rate is too high.

The inlet water temperature has

dropped

Adjust the service valve

Adjust the servicevalve

For a shower select inner or outer spray

pattern in the shower head to make best use of

the hotwater

Water flow too low or

temperature too high The mains supply water flow is too

low.

The hot tap is not fully open.

Increase the supply water flow. Make sure that

theservice valve is correctly adjusted

Adjust the servicevalve so that the water is at

the right temperature with the tap fully open.

Always turn the hot tap fully on

Water goes from hot to cold The water flow or pressure is too

low, and the thermal cut-out is

operating

A second outlet has been tuned on.

Increase the water flow. Make sure that the

servicevalve is correctly adjusted.

Refer to Powerstream Handbook

Do not use the basin whilst using the shower

Shower spray pattern

deteriorates The showerhead is clogged Cleanthe showerhead by simply regularly

rubbing the rubber nozzles

Professional Service

If the above checksfail to restore the performance, you should seek professi onal help.

The person who installed the unit is probably the best one to repair it and is certainly the person to contact if you have

had a problem in the guarantee period.

In the first instance check that the unit has been correctly installed before con tacting us at the number below.

After Sales Service

We offer a technical advisory service to contractors and customersneeding advice or with a problem.

RING 0844 372 7766

A. For Shower Cabinets and

Recessed Installations

Shower tailpipes can be passed

through cabinet wall in order to

make plumbing connection using

standard tap connectors.

Powerstream Shower Accessories

Schematic Installation Diagram showing Powerstream serving Shower and Basin

IMPORTANT NOTES

1. The HOT supply from the Powerstream MUST be connected to the red “turn on fully” control valve.

2. Please see the Powerstream handbook for full details of installation.

Setting the Outlet Water Temperature

Adjusting the service valve

Turn the service on, then-

• If the unit is to supply a basin.

Ø Turn on the hot water tap at the basin.

Ø Adjust the service valve until the water comes out of the tap at the required temperature.

Ø Check that the unit works correctly when the basin tap isclosed and then opened again,

if not, adjust the service valve slightly

• If the unit is to supply a shower.

Ø Turn the service valve anti-clockwise until the neon light goes out,

and then turn it back until the neon light just comes on.

Ø Check the water temperature of the handset and if necessary, turn the cold tap on and adjust to get the desired

shower temperature.

Ø Explain to the user that when he unit is used, the hot water should be turned on fully so that the water temperature is

always the same.

• Please refer to the Powerstream handbook for FULL details of operation and installation of the Powerstream.

IMPORTANT: Demonstrate the unit to the user and give them this guide

B. For Surface Mounting

Position adaptor to suit or

discard if not required.

Bind tailpipeswith P.T.F.E. tape

if necessary.

Screw on and orientate wall plate

elbows to suit incoming pipework.

Screw shower to surface of wall

using screw and wallplugs

provided.

Make plumbing connection.

Shower Mixer Valve User Instructions

Shower operation

•Check that the power is switched on at the mains isolator switch.

•Turn on the hot or “flow” tap fully (see diagram 1).

•If the unit has been used recently, run the water through for a f

ew seconds to let the temperature settle down.

You may get a short burst of very hot water front the unit.

•Turn on the cold or “temperature” tap, if necessary, to adjust the temperature of the water.

•Make sure that no other outlets connected to the unit are used whilst you are in the shower, or the water flow

will drop suddenly.

•When you have finished DO NOT switch off the power if you are going to use the unit again shortly.

•It is important to clean the shower headset regularly (see page 4)

•If the shower headset can reach the water in the shower tray, bath or basin, the shower hose should be fitted through

the hose-retaining loop on the soap tray. This will comply with the water by -laws.

Knob “A” “Turn on fully” hot water only.

This tap must be FULLY OPEN.

Knob “B” “Temperature control” tap used to bleed cold water

to give blended outlet temperature.

Note Knob “A” and Knob “B” MUST be switched off/closed

when finished showering.

What to do if things go wrong

Self Help

Symptom Cause What to do

Little or no water flows The main water supply is turned off Turn on the main supply valve at the stop valve

Cold water only – neon light off

The main water supply is not turned

on enough Turn on main supply fully at the stop valve

Cold water only – neon light on

The water flow rate is too high.

The inlet water temperature has

dropped

Adjust the service valve

For a shower select inner or outer spray

pattern in the shower head to make best use of

the hot water

Water flow too low or

temperature too high The mains supply water flow is too

low.

The hot tap is not fully open.

Increase the supply water flow. Make sure that

the service valve is correctly adjusted

Adjust the service valve so that the water is at

the right temperature with the tap fully open.

Always turn the hot tap fully on

Water goes from hot to cold The water flow or pressure is too

low, and the thermal cut-out is

operating

A second outlet has been tuned on.

Increase the water flow. Make sure that the

service valve is correctly adjusted.

Refer to Powerstream Handbook

Do not use the basin whilst using the shower

Shower spray pattern

deteriorates The showerhead is clogged Clean the showerhead by simply regularly

rubbing the rubber nozzles

Professional Service

If the above checks fail to restore the performance, you should seek professi onal help.

The person who installed the unit is probably the best one to repair it and is certainly the person to contact if you have

had a problem in the guarantee period.

In the first instance check that the unit has been correctly installed before con tacting us at the number below.

After Sales Service

We offer a technical advisory service to contractors and customers needing advice or with a problem.

RING 0344 879 3588

There are 3 defined spray plate settings adjustable by rotating the spray plate .

The modes have a positive “click” to identify them (see diagrams)

WARNING: YOU MUST REGULARLY INSPECT THE SHOWER HOSE

FOR WEAR AND DAMAGE. REPLACE IF NECESSARY,

OR EVERY TWO YEARS, WITH OUR APPROVED PART.

WARNING: IN ORDER TO MAINTAIN THE PERFORMANCE OF YOUR SHOWER,

YOU MUST CLEAN THE SHOWER HEADSET REGULARLY

All water contains particles of lime-scale, which build up in the shower headset

and unit reducing the performance.

It is therefore important to clean the shower headset by simply rubbing the rubber nozzles,

or soaking in proprietary lime-

scale remover and rinsing thoroughly before use.

In some winter conditions, when the incoming mains water is particularly cold

it may be necessary to select the inner or outer spray pattern only,

this will ensure correct operation of the shower with a slightly lower water flow rate.

Note:

After use it is normal for some water to drip from the shower handset for a

few moments. This inhibits lime-scale build-up over prolonged use.

Additional Accessories (Can be supplied against any Credit or Debit cards, ring 08744 372 7750

)

Chrome 1.25m long Shower Hose Cat No. 93-797641 White 2m long Shower Hose Cat No. 83-595308

Standard White/Chrome Accessory Kit Cat No. 83-595302 Chrome 2m long Shower Hose Cat No. 83-595310

Premium White/Chrome Accessory Kit Cat No. 83-595303 White 1m long Riser Rail Cat No. 83-595311

Curtain and Rail Pack with Non-Slip Mat Cat No. 83-792801 Chrome 1m long Riser Rail Cat No. 83-595312

Curtain and Rail Pack Cat No. 83-792802

SHOWER MIXER

HANDBOOK

(FOR USE WITH THE

REDRINGPOWERSTREAM)

IMPORTANT:

This booklet should be left with the user

after installation and demonstration

A4 Leaflet 579-2379-20c

UK only:

Xpelair products deliver reliable service for normal, household use in domestic settings. All Xpelair products are individually tested before leaving the factory.

If you are a cunsumer and you experience a problem with your Xpelair Product, which is found to be defective due to faulty materials and workmanship within the warranty

period, This Xpelair warranty will cover repair, or at the discretion of Xpelair replacement with a functionally equivalent Xpelair Product.

The Xpelair warranty period is Two calendar years from the date of purchas e of your Xpelair product, or the date of delivery of the product, if later. The Xpelair warranty is

conditional upon you providing the original purchase receipt proof of purchase. Please therefore retain your receipt as proof of purchsase.

If you do experience a problem with your Xpelair product please call the helpline on +44 (0) 344 879 3588 or at the address below. We will need details of your Xpelair

product, and a description of the fault which has occured. Once we receive your information and proof of purchase we will contact you to make the necessary arrangements.

Customers Outside UK - See international below.

If Your Xpelair product is not covered by this Xpelair warranty there may be a charge to repair your product. However, we will contact you for an agreement to any charges

before any chargeable service is carried out.

What is not covered by an Xpelair warranty?

The Xpelair warranty does not cover the following:

Any fault or damage to your Xpelair product due to faulty materials or workmanship occurring outside the Two year warranty period.

Any fault or damage occurring to any pre-owned product or to any other eqipment or property.

Accidental damage to your Xpelair product or damage to your Xpelair product from external surces (for example, transit, weather, elecrical outages or power surges).

Fault or damage to your Xpelair product which is:

Not due to faulty materials or workmans hip or which is due to circumstances outside Xpelairs control.

Caused by use of yout Xpelair product for anything other than normal domestic household purposes in the country where it is purchased.

Caused by any misus e, abuse or neglect use of the Xpelair produc, including but not limited to any failure to use it in accordance with the Operating Instructions supplied with

the product.

Caused by any failure to assemble, install, clean and maintain your Xpelair product in accordance with the Operating Instructions supplied with the product unless this was

carried out by Xpelair or its authorised dealers.

Caused by repairs or altercations to your Xpelair product not carried out by Xpelair service personnel or its authorised dealer(s).

Caused by use of any consumables or spare parts for your Xpelair product which are not Xpelair specified.

Terms ans Conditions

The Xpelair warranty is valid for Xpelair from the date of purchase of your Xpelair product from a recognised retailer in the country of purchase and use, or the date of deliver

of the product if later, always provided the original receipt has been retained and is produced as proof of purchase.

You must provide to Xpelair or its authorised agents on request the original receipt as proof of purchase and - if required by Xpelair - proof of delivery. If you are unable to

provide this documentation, you will be required to pay for any repair work required.

Any repair work under the Xpelair warranty will be carried out by Xpelair or its authorised dealer(s) and any parts that are replaced will become the property of Xpelair. Any

repairs performed under the Xpelair warranty will not extend the warranty period.

Any replacement of your Xpelair product by Xpelair during the warranty period will s tart the Two year warranty period afresh from the date of delivery of replacement Xpelair

product to you.

The Xpelair warranty does not entitle you to recover of any indirect or consequential loss or damage including but not limited to los s or damage to any other property.

The Xpelair warranty is in addition to your statutory rights as a consumer and your statutory rights are not affected by this Xpelair warranty.

Contact Xpelair

If you have any questions about what the Xpelair warranty covers and does not cover or how to claim under Xpelair warranty, please contact us using the information below.

Contact Details

Millbrook House, Grange Drive, Hedge End, Southampton, SO30 2DF

Telephone: +44 (0)344 879 3588

Email: customer.se[email protected]

http\\www.xpelair.co.uk

International

Warranty: Contact your local dis tributor or Xpelair direct for details.

Technical advice and service: Contact your local Xpelair distributor.

Xpelair: A brand of GDC Group Limited, trading as Glen Dimplex Heating & Ventilation

For electrical products sold within the European Community. At the end of the electrical products useful life it should

not be disposed of with household waste. Please recycle where facilities exist. Check with a Local Authority or retailer

for recycling advise in your country. Batteries should be disposed of or recycled in accordance with WEEE Directive