Minka Group P1553-66A-L User manual

Minka Group
Brand
Minka Group
Model
P1553-66A-L
Type
User manual

This manual is also suitable for

Minka Group P1553-66A-L:

This dimmable flush mount light fixture is suitable for various indoor lighting applications. Its LED module provides energy efficiency and long-lasting illumination. The fixture is compatible with ELV and LED-compatible wall dimmer switches, allowing you to adjust the brightness to your desired level. Installation is straightforward and can be completed by following the included instructions. The fixture's contemporary design complements a range of décor styles, making it a versatile choice for residential or commercial spaces.

Minka Group P1553-66A-L:

This dimmable flush mount light fixture is suitable for various indoor lighting applications. Its LED module provides energy efficiency and long-lasting illumination. The fixture is compatible with ELV and LED-compatible wall dimmer switches, allowing you to adjust the brightness to your desired level. Installation is straightforward and can be completed by following the included instructions. The fixture's contemporary design complements a range of décor styles, making it a versatile choice for residential or commercial spaces.

Fig. 2
H
O
U
S
E
F
X
T
UR
E
H
O
U
S
E
F
I
X
T
UR
E
H
O
U
S
E
F
X
T
UR
E
B
l
a
ck
o
r
W
h
i
te
o
r
Ba
r
e
S
m
o
o
th
Ri
bb
e
d
C
op
p
e
r
(
G
r
ou
n
d
)
W
R
E
S
W
I
R
E
S
W
I
R
E
S
(H
o
t)
(N
eu
t
r
a
l
)
(
G
r
ou
n
d
)
INSTALLATION INSTRUCTIONS
Item#P1551-66A-L P1552-66A-L P1553-66A-L (Rev. 05/09/2023)
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARATION
1.
Shut off power at the fuse box or circuit breaker box. If
necessary, remove the old fixture and mounting hardware.
2.
Carefully unpack your new fixture and lay out all the parts
on a clear area. Take care not to lose any small
parts
necessary for installation.
Fig. 1
Set #A-020-150A for item# P1551-66A-L
Set #A-020-300 for item# P1552-66A-L
Set #A-020-400 for item# P1553-66A-L
- Mounting plate
- Junction box screw* 2 pcs
- Ground Screw
Outlet box
MOUNTING THE FIXTURE (FIG. 1)
3.
Secure mounting plate (A) to the outlet box (not included)
using outlet box screws (B) (Size: #8-32N*L1”L).
The side
of the mounting plate marked “GND” must face
out.
CONNECTING THE WIRES (FIG. 2)
4.
Connect the electrical wires as shown in Fig. 2,
making sure
that all wire connectors are secured. If your
outlet box has
a ground wire (green or bare copper),
connect the fixture's
ground wire to it. Otherwise, connect the fixture's ground
wire directly to the mounting plate (A) using the green
screw provided. After wires are
connected, tuck them
carefully inside the outlet box.
FINISHING THE INSTALLATION (Fig. 1)
5.
Place back plate (C) over mounting plate (A) and secure
with screws (D).
A
Glass Shade #
PG1551 for item# P1551-66A-L
PG1552 for item# P1552-66A-L
PG1553 for item# P1553-66A-L
B D C
Replacing LED module (Fig.3)
The LED module can be replaced by a qualified electrician
without cutting of wire and without damage to any decorative
element to which the fixture is attached. See installation steps
for more details (Fig 3.)
a. Shut off the power.
b. To remove fixture body from wall, loosen screws (D) and back plate
(C) from mounting plate (A). Disconnect wire connectors and place
fixture body on a clean surface (Fig.1).
c. Remove screws (E) and the metal caps (H) from the fixture body
and remove glass (F).
d. Press the button with printed ''L'' quick connector on LED module
(G) with screwdriver (not included) to disconnect the black wire
and then disconnect the white wire from the printed ''N'' quick
connector on LED module (G). Carefully remove LED module (G)
from the base.
e. Reverse steps a-d for installing the new LED module.
Your installation is now complete. Return power to the
outlet
box and test the fixture.
Note: The illustration in figure 1 on this manual is for
installation purposes only. It may or may not be identical to
the fixture purchased.
Dimmable with ELV and/or LED compatible wall dimmer
switches
Fig. 3
E
G
F Screwdriver
H
Page: 1/1
P1551-66A-L P1552-66A-L P1553-66A-L
  • Page 1 1

Minka Group P1553-66A-L User manual

Minka Group
Brand
Minka Group
Model
P1553-66A-L
Type
User manual
This manual is also suitable for

Minka Group P1553-66A-L:

This dimmable flush mount light fixture is suitable for various indoor lighting applications. Its LED module provides energy efficiency and long-lasting illumination. The fixture is compatible with ELV and LED-compatible wall dimmer switches, allowing you to adjust the brightness to your desired level. Installation is straightforward and can be completed by following the included instructions. The fixture's contemporary design complements a range of décor styles, making it a versatile choice for residential or commercial spaces.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents