Officine Gullo CVCS4EM Instructions For Installation And Use Manual

Brand
Officine Gullo
Model
CVCS4EM
Type
Instructions For Installation And Use Manual
x
INSTRUCTIONS
for installation and use
PASTA COOKER FOR
RESIDENTIAL AND PROFESSIONAL USE
CVCS4EM
TABLE OF CONTENTS
WARNINGS & CAUTION............................................................................4
SAFETY INSTRUCTIONS .........................................................................5
ELECTRICAL SCHEME.............................................................................6
INSTALLATION INTRUCTIONS.................................................................7
USE AND MAINTENANCE INSTRUCTIONS.............................................9
CLEANING AND CARE INSTRUCTIONS................................................10
4
Ofcine Gullo
WARNINGS & CAUTION
1. Before using the appliance, read the instruction manual carefully, as it contains important safety infor-
mation on the proper installation, use and maintenance of the appliance. Please keep the instruction
manual for further reference.
2. The appliance’s electrical safety is guaranteed only if the electrical system is grounded in accordance
with the relevant regulations. It is of the utmost importance to follow such regulations; when in doubt,
please consult a qualied electrician to have the electrical system thoroughly checked. The manufac-
turer declines all responsibility for damage caused by a improperly grounded electrical system
3. Before connecting the appliance, make sure that the appliance’s technical characteristics shown on
the tag correspond to those of the electrical system and gas supply.
4. Make sure that the electrical system and sockets can handle the appliance’s maximum power con-
sumption as shown on the tag. When in doubt, please consult a qualied electrician.
5. When not in use for extended periods, switch off the general power supply to the appliance and close
the gas supply valve.
6. Do not obstruct the appliance’s cooling or heat dissipation vents.
7. The appliance must be used only for the purposes for which it has been expressly designed (cooking).
All other uses (such as the heating of a room) are considered inappropriate and therefore dangerous.
The manufacturer declines all responsibility for damage resulting from improper use of the appliance.
8. The use of any electric appliance implies the observance of some basic rules. More specically:
- Avoid the use of extension cords and, if necessary, take all precautions;
- Do not pull the power cord to disconnect the plug from the power socket;
- Do not allow children or untrained persons to use the appliance.
9. Before performing maintenance work, disconnect the appliance by pulling the plug out of the power
socket or turning off the main switch.
10. In case of failure or malfunction, turn the appliance off, close the gas supply valve and do not at-
tempt to carry out any repairs, which must be done exclusively by an authorized service center.
5
Ofcine Gullo
SAFETY INSTRUCTIONS
Do not store or use gasoline or other ammable vapors or liquids in the vicinity of this or
any other appliance.
WARNING: Improper installation, adjustment,alteration, service or maintenance can
cause property damage, injury or death. Read the installation, operating and maintenance
instructions thoroughly before installing or servicing this equipment.
To avoid personal injury or property damage, please read and follow these important safety
precautions.
1. Before any maintenance or repairs are performed, disconnect the appliance from the
electric and gas supply.
2. Your appliance should be installed by a qualied gas installation technician. Have the
technician show you the exact location of the gas shutoff valve on the incoming gas line so
you know how to turn off the gas if necessary.
3. In the event of a power failure, do not attempt to operate the appliance or light any of the
burners. This is a gas red appliance that employs electrical components such as the ignition
and safety devices.
4. Do not attempt to repair or replace any part of this appliance unless specically instructed
to do so by this manual. In-warranty service must be performed by an authorized service
agency.
5. Do not store ammable materials on or near the appliance. Keep the appliance area clean
and free of combustible materials, gasoline and other ammable vapors and liquids. A check
before each use to determine that no hazardous materials are in the area is recommended.
6. Children should not be left alone or unattended in the kitchen while the appliance is in use.
7. This appliance should not be operated without a properly sized and operational ventilation
hood.
8. The ventilation and ue ways of this appliance must remain unobstructed at all times.
9. Do not store items of interest to children above the appliance. Children, as well as adults,
should never be allowed to sit, stand, or climb on any part of the appliance. Serious injury
may occur.
10. Never leave the appliance unattended during use. Boil-overs may occur, causing spills
which may ignite.
11. Do not use water on grease res. Never pick up a aming pan. It is recommended you
purchase a multi-purpose dry chemical or foam- type re extinguisher for your home. Store it
in close proximity to your appliance.
12. If you are aming liquor or other spirits, and you're appliance is installed under a vent
hood, TURN THE FAN OFF. The draft created could cause the ames to spread out of control.
13. For your safety, never use your appliance or any other cooking appliance as a space
heater to warm or heat the room.
14. Use only dry potholders. Moist or damp potholders on hot surfaces may result in steam
burns. Do not allow potholders to touch hot burner areas. Do not use a towel or other bulky
material as a potholder.
15. To reduce the risk of burns, ignition of ammable materials, and spillage, the handle of
any pot or pan should be positioned so that it does not extend over adjacent burners or the
front of the appliance.
6
Ofcine Gullo
FIG.A
ELECTRICAL / SCHEME
The installation of this appliance must conform with all applicable local codes.
In the absence of local codes, the installation must conform to the latest level of the Na-
tional Electric Code, ANSI/NFPA 70.
If the electrical supply is not turned on or is interrupted the appliance will not operate. The
applicable wiring diagram for this appliance is below. The circuit where you wire your ap-
pliance to must be grounded and polarized. We recommend the circuit for your appliance
be a non-GCFI dedicated line.
CVCS4EM
TABELLA DATI TECNICI CP-74EM CP-74ET CP-78ET 230Vac 7,8 kW 15,6 kW.doc
FIG.A
SCHEMA ELETTRICO , SCHALTPLAN, SCHEMA ELECTRIQUE , WIRING
DIAGRAM, ESQUEMA ELECTRICO
549025300 M00_00 , 549021400 M00_00
230V~ 50/60Hz 230V~3 50/60Hz
1-2
Commutatore Schalter Commutateur Commutator Conmutador
3
Morsettiera Klemmleiste Bornier Junction-box Tablero de bornes
4
Morsettiera
commutazione Switching
Klemmenblock Bornier de commutation Switching terminal
block Tablero de bornes de
conmutación
5
Resistenze Widerstände Résistances Elements Resistencias
6
Spia bianca weiße Kontroll-Leuchte Témoin blanc White light Luz indicadora blanca
7
Spia verde grüne Kontroll-Leuchte Témoin vert Green light Luz indicadora verde
8
Termostato sicurezza
Teleruttore Sicherheits-thermostat Thermostat de sécurité Safety Thermostat Termostato seguridad
MODELLI
MODELLE
MODELES
MODELS
MODELOS
Morsettiera Nr.1
Klemm-leiste Nr.1
Bornier Nr.1
Junction-box Nr.1
Tablero de bornes Nr.1
CP-74ET FIG.A
CP-78ET FIG.A + FIG.A
interruzione pagina
1. Commutator
2. Commutator
3. Junction box
4. Switching terminal block
5. Elements
6. White light
7. Green light
8. Safety Thermostat
7
Ofcine Gullo
INSTALLATION INSTRUCTIONS
This appliance is Manufactured by OFFICINE GULLO S.r.l
Headquarters and factory
50012 Antella - Bagno a Ripoli (FI) Italy
via della Torricella, 29, - Tel. +39 055 6560324
In the US call (800)-781-7125
Home page http:// www.ofcinegullousa.com
E-Mail: info@ofcinegullousa.com
The manufacturer declines any responsibility for direct or indirect damage caused by
improper or incorrect installation, alterations, maintenance or use of the appliance, as in all
the other cases considered in the items of our sales conditions.
BEFORE YOU BEGIN
The manufacturer declines all responsibility in the event of failure to observe the instructions
given here for installation, maintenance and suitable operation of the product. The
manufacturer further declines all responsibility for injury due to negligence and the warranty
of the unit automatically expires due to improper maintenance and/or installation.
BEFORE YOU BEGIN: Take the appliance out of its packaging.
Remove the protection lm.
It is advisable to test run the appliance before installation.
BEFORE STARTING please read this entire document and ensure you are fully conversant
with the requirements and limitations.
ELECTRICAL INSTALLATION
The data plate is on the front panel (see diagram in electric connection item) and has all the
data necessary for the connection.
When tting, the appliance must be levelled using a spirit level; slight differences of level
can be adjusted by screwing or unscrewing the adjustable feet. The main switch or the
socket must be near the appliance and easily accessibile.
It is advisable to place the appliance under an extractor hood so that steam is extracted
rapidly. If the appliance is placed near walls, dividing panels, kitchen furniture, decorative
nishings, etc., these should be in ameproof material; otherwise it is necessary to cover
them with non-ammable material.
Above all, it is necessary to ensure that the re prevention norms are observed.
All operations done when installing must be carried out observing the norms in force.
The manufacturer declines all responsibility in the event of incorrect functioning due to
wrong installation or installation which does not comply with the norms.
Attention! the manufacturer cannot be held responsible for and does not cover in the
guarantee any damage resulting from bad or faulty connections.
Attention! In accordance with international rules, when connecting the appliance, an
automatic device enabling the disconnection of all contacts from the mains, must be
installed above it; this device must have a contacts opening of at least 3 mm.
8
Ofcine Gullo
Electrical Supply.
This appliance requires electrical supply ensure an appropriately qualied person
completes the electrical oven-up. The appliance must be connected to an equipotential
system.
The connection screw is positioned at the back of the appliance and is identied by
the symbol .
The appliance is supplied without the connection cable. To install the power supply
cable, proceed as follows:
- Disconnect the power supply.
- Remove the bottom panel
- Push the connection cable through the cable blocker, connect the conductor wires
to the corresponding terminals in the junction box and x them into place.
- Block the cable with the cable blocker, and reassemble the bottom panel. The earth
wire must be longer than the others so that if the cable blocker should break, it will
disconnect after the tension wires.
The connection cable must have an adequate section for the power of the appliance
and be resistant to a temperature of at least 150°C (see technical data table).
DIMENSIONS
cm POWER SUPPLY Power
max kW
Absorbition
max A
Power
supply cable
CVCS4EM 40 x 70 x 90h 230V~ 50/60 Hz 7,8 33,91 A 3 x 6 mm²
TECHNICAL ELECTRICAL DATA TABLE
9
Ofcine Gullo
USE AND MAINTENANCE INSTRUCTIONS
STARTING UP
Before using the appliance, it is necessary to clean it carefully, especially the tub (see
paragraph “cleaning and care”).
Check the connection of the appliance and start it up following the instructions.
INSTRUCTIONS FOR USE
Attention! Use the appliance only under surveillance.
- Never start up the appliance without water.
With pasta cookers it is possible to cook pasta, vegetables, rice, eggs, legumes, etc.
WATER SUPPLY CHARACTERISTICS
The system must be connected to a drinking water supply with the following
Characteristics. Failure to do so automatically invalidates the guarantee:
Total hardness: 0,5 to 5°F to prevent the build-up of lime-scale
Pressure: 50 to 250 kPa (0,5-2,5 bar).
Chlorine ion concentration (Cl-): not more than 10 ppm (acceptable value) to avoid
damaging the internal steel elements
pH: over 7
Electrical conductivity: 50 to 2000 μS/cm (20°C)
TURNING ON
Check that the water drainage tap is turned off.
1) When powering the device, the red light ashes briey for about ½ second.
2) In the absence of water in the tank the red light keeps ashing.
3a) Turn on the tap to load the tank to the desired level, which must be higher than the
minimum level probe and do not exceed the maximum level, which is marked on the tank
by the symbol (--)
3b) In models with automatic load, the water starts loading and you can select the desired
level by pressing the button with symbol (level button)
4) Switch on the main switch installed above the appliance. Turn the control knob
corresponding to the hotplate from position “0” to the degree of coking desired, between
1 and 4.
The white light shows that the heating element is working.
To turn off the appliance, turn the knob into position “O”.
10
Ofcine Gullo
EMPTYING THE TUB MOD. CVC...
To carry out this operation, it is necessary to open the outlet tap (lever in vertical position)
which can only be reached through the cabinet door situated below the appliance.
ANOMALIES
If the probe does not detect the presence of water in the tank for more than 15 sec. the
system disables the heating element: the alarm is indicated by a ashing red light
When the probe returns to detect the presence of water, the heating element is activated
and the red light is turned off.
NOTE: the lling phase is monitored by the system through the TIME-OUT.
TIME- OUT
After discovering the level probe, the micro controller triggers an internal timer relative
to the duration of this phase. If (continuous) loading takes longer than 350 seconds, the
system blocks the functions of the device and the alarm is signalled by the steady red
light.
To reset the alarm condition, after removing the fault that caused the intervention (broken
or disconnected level probes, problems with the water supply, drain valve open...), the
system must be turned OFF/ON.
CARE AND CLEANING INSTRUCTIONS
CLEANING AND MAINTENANCE
Attention! During cleaning, do not wash the external parts of the appliance with direct
sprays of water or with high pressure.
After every use, clean the appliance thoroughly. Daily cleaning after switching off the ap-
pliance ensures the perfect functioning and long life of the appliance.
Before starting to clean the appliance, disconnect the power supply. The parts in steel must
be washed with hot water and neutral detergent, then rinsed thoroughly in order to eliminate
all traces of detergent; after which, dried with a dry cloth. Do not use abrasive or corrosive
detergents.
All residues of food must be removed from the hotplate with the proper spatula. The surface
must be cleaned well and then greased with a lm of vegetable oil. Remove the drip pan,
empty it and wash it carefully.
11
Ofcine Gullo
CLEANING BURNISHED BRASS SURFACES
No synthetic protective varnishes have been used to obtain the special burnishing effect on
the burnished brass details in order to avoid spoiling the beauty of the brass with an articial
patina. The antique nish of the surface is the result of natural oxidation that has simply
been accelerated. All the natural antique nish brass surfaces can be cleaned with mild
soap and warm water, accompanied by the use of an abrasive pad (the green color type
used for washing dishes). It is recommended that the metal be rubbed, uniformly applying
light pressure, use caution as this will remove some of the patina if rubbed excessvily.
The brass details should then be dried.
Do not use metal polish as this is suitable not to clean the antique nish and could result in
loos of the color and patina. Oxidation that may appear over time on the burnished brass
surfaces is a normal characteristic of our craft metal working processes.
CLEANING CHROME PLATED BRASS SURFACES
No synthetic varnishes have been used to obtain the special polish on the chromium-plated
brass details in order to avoid spoiling the beauty of the chrome with an articial patina. All
the chromed surfaces should be clean as needed with a warm water and mild soap and a
soft cloth or micro-ber. Do not use abrasive pads.
CLEANING SATIN FINISH NICKEL PLATED BRASS SURFACES
No synthetic varnishes have been used to obtain the special nickel-plating on the satin
nish nickel-plated brass details in order to avoid spoiling the beauty of the nickel-plated,
satin nished solid brass with an articial patina. All the nickel-plated and satin nished
brass surfaces should be cleaned, where necessary, with a soft cloth or micro-ber cloth,
combined with a neutral detergent, if required. Do not use abrasive pads.
CLEANING THE VARNISHED SURFACES
All the varnished surfaces should be cleaned using a mild soap and, where necessary, a
soft cloth or micro-ber cloth. Do not use abrasive pads or any other chemical products.
CLEANING BRUSHED STEEL SURFACES
All the brushed steel surfaces should be cleaned using degreasing products or products
specically designed to be used on steel and, where necessary, extra-ne steel wool.
WHAT TO DO IN THE EVENT OF A BREAKDOWN
Turn off the machine and notify your authorized service center or call our main line at
1-(800) 781-7125
WWW.OFFICINEGULLO.COM
V 2.3 - 11.17
OFFICINE GULLO S.R.L.: via della Torricella 29, 50012 Antella - Bagno a Ripoli (FI)
Tel. +39 055 6560324 / 621807 - Fax: + 39 055 620670 - [email protected]
us
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Officine Gullo CVCS4EM Instructions For Installation And Use Manual

Brand
Officine Gullo
Model
CVCS4EM
Type
Instructions For Installation And Use Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents