Barco R5976922/03 User manual
- Category
- Bar code readers
- Type
- User manual
This manual is also suitable for
Barco R5976922/03 is a universal lamp house designed for use with FLM projectors. It is a replacement lamp house that can be installed in place of the original lamp house that came with the projector. The universal lamp house offers several advantages over the original lamp house, including:
- Increased lamp life: The universal lamp house uses a new type of lamp that has a longer lifespan than the original lamp. This can save you money on replacement lamps in the long run.
- Improved light output: The universal lamp house produces a brighter image than the original lamp house, which can be beneficial for use in large venues or in situations where there is a lot of ambient light.
Barco R5976922/03 is a universal lamp house designed for use with FLM projectors. It is a replacement lamp house that can be installed in place of the original lamp house that came with the projector. The universal lamp house offers several advantages over the original lamp house, including:
- Increased lamp life: The universal lamp house uses a new type of lamp that has a longer lifespan than the original lamp. This can save you money on replacement lamps in the long run.
- Improved light output: The universal lamp house produces a brighter image than the original lamp house, which can be beneficial for use in large venues or in situations where there is a lot of ambient light.
FLM lamp house
Installation manual
R5976922/03
18/11/2008
Barco nv Events
Noordlaan 5, B-8520 Kuurne
Phone: +32 56.36.89.70
Fax: +32 56.36.88.24
E-mail: [email protected]
Visit us at the web: www.barco.com
Printed in Belgium
1. Installation process
1. INSTALLATION PROCESS
About this chapter
This chapter describes how to replace the (universal) lamp house from the FLM projector.
Adapted software for Universal Lamp House
The FLM projector software m ust be upgraded to version 1.7.17 or later prior to using the Universal Lamp House. The latest FLM
projector software c an be downloaded from the Barco secured web site h
ttps://my.barco.com (browse to the product page of the
FLM projector). The F LM projector will not reco gnize the Unive rsal Lamp Hous e and will fail to s tart up the xenon bulb lamp when
neglecting this software upgrade. Use the Projector Toolset, which is also available on the sec ured B arco web site, to upgrade the
projector software. See user guide of the Projector Toolset for detailed instructions on how to upgraded the projector software.
Overview
• Switching off
• Removal of the lamp c over
• Removal of the lamp hous e
• Installation of the lamp house
• Installation of the lamp cover
1.1 Switching off
How to switch off the projector?
1. Press first Standby.
2. Let cool down the projector un til the fans decrease, at least 5 min.
3. Switch off the projector with the power switch.
1.2 Removal of the lamp cover
WARNING: This procedure may only be performed by qualified technical service personnel.
Necessary tools
7mmflat screw driver.
How to remov e the lamp cover of the projector ?
1. Release the two captive screws at the top and b ottom r ight s ide of the lamp cover, using a flat screw driv e r.
R5976922 FLM LAMP HOUSE 18/11/2008
1
1. Installation process
Image 1-1
2. Remove the lamp cover from the projector doing the following:
a) gently pull out the left bottom corner (A) o f the lamp cover,
b) then gently pull out the left top corner (B) of the lamp cover,
c) then m ove the lamp cover away from the projector (C).
Image 1-2
1.3 Removal of the lamp house
WARNING: This procedure may only be performed by qualified technical service personnel.
CAUTION: Never attemp t to disassemb le the lamp from its housing or to dispose of it. Return it t o Ba rco.
Due to its high internal pressure, the lamp ma y explode in either hot or cold states if imp roperly hand led.
Necessary tools
7mmflat screw driver.
How to remove the lamp house of the projector ?
1. Switch off the projector and unplug the power cord at the projector side.
2. Remove the lamp cover, see "Removal of the lamp cover", page 1 .
3. Release the three spring lock screw s of the lamp house a s illustrated.
2
R5976922 FLM LAMP HOUSE 18/11/2008
1. Installation process
Image 1-3
4. Clasp the lamp h ouse by the handles and pull the lamp house out o f the projector.
Image 1-4
While starting u p the projector, the electronics detect if a lamp is ins talled. If no lamp is i nstalled, it is no t
possible to start up the projector.
1.4 Installation of the lamp house
WARNING: This procedure may only be performed by qualified technical service personnel.
CAUTION: Never attemp t to disassemb le the lamp from its housing or to dispose of it. Return it t o Ba rco.
Due to its high internal pressure, the lamp ma y explode in either hot or cold states if imp roperly hand led.
Necessary tools
7mmflat screw driver.
How to install the lamp house of the projector ?
1. Ensure the projec tor is switched off and the power cord at the projector side is unplugged.
2. Remove the lamp cover, if not removed yet. S ee "Removal of the lamp cover", page 1 .
R5976922 FLM LAMP HOUSE 18/11/2008
3
1. Installation process
3. Clasp the lamp house by its handles an d gently slide the lamp hous e into its socket. Note that the com partment is provided with
guides (G) to position the lam p house correctly.
G
C
Image 1-5
4. Push the lamp house forward until it slides fully into the projector.
5. Secure the correct position of the lamp house by tightening all three spring lock screws as illustrated.
Image 1-6
6. Reinstall the lamp cover of the proj
ector, see "Installation of the lamp cover", page 4 .
While starting u p the projector, the electronics detect if a lamp is ins talled. If no lamp is i nstalled, it is no t
possible to start up the projector.
1.5 Installation of t he lamp cover
Necessary tools
7mmflat screw driver.
How to install the lamp cove
r of the projector ?
1. Install the lamp cover of the projector doing the following:
a) Bring the lam p cover towards its final po sition (A),
b) then gently push the locking s tud at the left top corner (B) into its receiver,
c) then gently pu sh the locking stud at the left bottom corner (C) into its r eceiver.
4
R5976922 FLM LAMP HOUSE 18/11/2008
1. Installation process
Image 1-7
2. Secure the lamp cover by locking the two captive screws at the right side of the lam p cover.
Image 1-8
R5976922 FLM LAMP HOUSE 18/11/2008 5
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Barco R5976922/03 User manual
- Category
- Bar code readers
- Type
- User manual
- This manual is also suitable for
Barco R5976922/03 is a universal lamp house designed for use with FLM projectors. It is a replacement lamp house that can be installed in place of the original lamp house that came with the projector. The universal lamp house offers several advantages over the original lamp house, including:
- Increased lamp life: The universal lamp house uses a new type of lamp that has a longer lifespan than the original lamp. This can save you money on replacement lamps in the long run.
- Improved light output: The universal lamp house produces a brighter image than the original lamp house, which can be beneficial for use in large venues or in situations where there is a lot of ambient light.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Barco DP-2000 Installation guide
-
-
Barco DMX adapter Installation guide
-
-
-
Barco R5975236 User guide
-
Barco HDF-W26 Installation guide
-
-
-
Barco SFP input card User guide