2. LIGHT MY BRICKS
  3. 21310

LIGHT MY BRICKS 21310 Operating instructions

  • Hello! I've reviewed the Light My Bricks user guide for the Old Fishing Store Lighting Kit. This document provides detailed instructions on how to install the lighting kit, including connecting different types of lights, using the expansion board, and choosing a power source. I'm ready to help answer your questions about the installation process and the kit's features.
  • What do I do if a connector does not easily fit into a port?
    How do I install Bit Lights under LEGO pieces?
    How do I connect cable connectors to the Expansion Board?
Here is the instructions document for the LEGO Old Fishing Store LED lighting kit.
Please read and follow the steps carefully to ensure this lighting kit is installed
properly.
If you run into any issues, please refer to the online troubleshooting guide.
This user guide is also available to download in PDF format here.
Light My Bricks: Old Fishing Store Lighting Kit
Package contents:
4x White 15cm Bit Lights
3x White Strip Lights
1x 6-Port Expansion Board
1x 30cm Connecting Cable
1x 15cm Connecting Cable
1x 5cm Connecting Cable
1xAA Battery Pack (requires 3x AA Batteries)
OR
1x USB Power Cable
Note – AA Battery Pack will be replaced with USB Power Cables from mid
April 2020
LEGO pieces
2x Plates 1×6
Important things tonote:
Laying cables in between and underneath bricks
Cables can t in between and underneath LEGO® bricks, plates, and tiles providing
they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO®
together around cables; instead ensure they are laying comfortably in between each
stud.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors
can be inserted only one way. With the expansion board facing up, look for the
soldered “=” symbol on the left side of the port. The connector side with the wires
exposed should be facing toward the soldered “=” symbol as you insert into the port.
If a plug won’t t easily into a port connector, do not force it.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging
the cable andlight.
“
Connecting cable connectors to StripLights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors
can be inserted only one way. With the Strip Light facing up, ensure the side of the
connector with the wires exposed is facing down. If a plug won’t t easily into a port
connector, don’t force it. Doing so will damage the plug and the connector.
Incorrectly inserting the connector can can result in bent pins inside the
port or possible overheating of the expansion board when connected.
“
Installing Bit Lights under LEGO® bricks andplates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct
way up (Yellow LED component exposed). You can either place them directly on top
of LEGO® studs or in between.
OK, Let’s Begin!
1.) Start by removing the upper level as well as the main roof section.
Remove the lamp section and then disassemble as per below.
2.) Take a White 15cm Bit Light and then thread the connector side through the hole
on top of the bottom piece. Thread it all the way through until the LED is at against
the top of the piece.
You may need bend the LED slightly so that it sits at against the top of the
LEGOpiece
Reconnect the top section to secure the LED in place.
Reconnect the lamp back to the desk inside the building ensuring the cable is
facing the front left corner so that it is not visible if you look in the window.
3.) Take the top section of the Old Fishing Store and remove the roof.
Disconnect the at clear 2×2 boat stud piece from underneath the roof and then
take a White 15cm Bit Light and place it directly in the centre. Reconnect the at
clear boat stud piece directly over the Bit Light to secure it in place.
Ensure the LED is the correct way facingup
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/