Lefroy Brooks LB 4958 Installation & Servicing Guide

Type
Installation & Servicing Guide

This manual is also suitable for

4509 / 4939 / 4943 / 4946 / 4955 / 4958 / 4961
MIRROR INSTALLATION
& GLASS REPLACEMENT GUIDE
405mm
448mm
370mm
505mm
LB 4958
LB 4955
LB 4946 LB 4939 & RT 4939
LB 4509 LB 4961
448mm
405mm
505mm
500mm
443mm
400mm
546mm
500mm
600mm
190mm
585mm maximum
110mm minimum
290mm max.
180mm min.
190mm centres
Ø50mm
190mm
382mm
Ø145mm
2
DIMENSIONS
Not to scale
RT 4943
Shown with single bracket. Supplied as a pair.
LB 4943
Shown with single bracket. Supplied as a pair.
66mm
50mm 45mm
62mm
50mm 37mm
3
DIMENSIONS
Not to scale
4
MIRROR INSTALLATION & REPLACEMENT
Professional installation
We recommend that our products are fitted by
a fully qualified professional. A tester should
be used to ensure there are no hidden pipes or
electrical cables where the product is to
be installed.
Wallxings
The screws and wall plugs provided are suitable
for most brick walls. However, if the wall is
constructed of plasterboard or soft building block
the appropriate fixings should be used.
Installation
We recommend the use of a spirit level to ensure
the brackets are level.
Should the mirror be damaged at any time it is
recommended you follow the guidelines opposite.
Always wear protective eye-wear and suitable
gloves when attempting a repair.
Nylon locking screws
5
WALL MIRROR GLASS REPLACEMENT
For vanity & shaving mirror glass replacement, please see following section.
Mirror product code Spares number Description
LB 4939 & RT 4939 PCG023 Arched top
LB 4946 PCG024 Octagonal
LB 4961 PCG025 Oval
LB 4509 mirror glass is retained using adhesive. Replacement is dicult.
We advise ringing the customer service department for advice.
1 Take all necessary safety precautions to
protect yourself from injury. Ensure that the
mirror is supported.
2 Remove the fixing screws from the mirror
brackets.
3 Remove the mirror and brackets from the
wall and place reflective side down on a flat
surface/work table.
4 Using a flat bladed screwdriver, unscrew the
two nylon locking screws at the rear of
each bracket.
5 Any damaged pieces of mirror can now
be removed.
6 With the reflective side of the mirror facing
down, position the mirror brackets in a central
location. The nylon locking screws in the
brackets should be at the rear of the mirror.
Tighten the nylon locking screws.
7 The mirror can now be fitted to the wall.
To do this, locate the mirror and line up the
fixing holes with those in the mirror brackets.
Use the screws removed previously to secure
in place.
We recommend that two people remove and fit the mirror. This will reduce the chance of injury and
damage.
Thumb screw
Thumb screw
6
REPLACING THE VANITY/SHAVING MIRROR GLASS
Mirror product code Spares number Mirror glass description
LB 4955 & LB 4958 PCG017 Plain
PCG018 Magnifying (2:1)
1 Take all necessary safety precautions to
protect yourself from injury. Ensure that the
mirror is supported.
2 Unscrew and remove the thumb screws from
both sides of the mirror then lift the mirror
assembly clear of the base/support.
Mirror frame
Mirror frame
Fixing screws
Fixing screws
Bracket
Mirror glass
Mirror glass
Bracket
Sponge mirror backing
7
3 Remove the four screws from the sides of the
mirror assembly.
4 Remove both brackets from the mirror frame.
5 Slide the two piece mirror frame away from
the mirror glass.
6 Remove damaged mirror and replace.
7 Hold the mirrors and foam backing firmly then
slide the mirror frame into place. It may be
necessary to compress the foam slightly when
sliding the mirror frame in place.
8 With both sections of the mirror frame in
place locate the brackets and align the
screw holes.
9 Insert and tighten the four fixing screws.
10 Locate the mirror assembly to the
base/support. Use the thumb screws removed
previously to secure in place.
Whilst every effort is made to ensure the accuracy of these, they are subject to change without notice as part
of the company’s product development process. The use of trademarks, product design and artwork is subject to
licence or agreement with LBIP Ltd. The design registrations, trademark registrations and copyrights are protected
by law and the use or reproduction outside the terms of an agreement is prohibited. The right to modify designs
and dimensions is reserved. LBIP Ltd is a member of ACID (Anti Copying in Design). E&OE
© LBIP Ltd 2023
CONTRACT ENQUIRIES
+44 (0)1992 708 316
info@lefroybrooks.co.uk
CUSTOMER SERVICE, SPARES & TECHNICAL ENQUIRIES
+44 (0)1902 390 894
technical@lefroybrooks.co.uk
LEFROYBROOKS.CO.UK
20.065.129D / MARCH 2023
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Lefroy Brooks LB 4958 Installation & Servicing Guide

Type
Installation & Servicing Guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI