Marv MW10EU2 User manual

Category
Print & Scan
Type
User manual

This manual is also suitable for

Read this manual first.
Please read this manual before operating this product.
After you finish reading this manual, store it in a safe place for future reference.
User's Manual
MARV User Manual
2
Contents
Using Safe Mode 22
How to turn off [Safe Mode] at the
machine
How to turn [Safe Mode] OFF → ON
at the machine
Handling an Object after Printing 23
Removing the object from the
print bed
Removing the raft and support
structures (if necessary)
Using the MARV Software 24
Main screen
Editing functions
Settings
MARV Maintenance 29
Replacing a Filament 29
Replacing the Filament
while Printing 30
Calibrating the Nozzle 31
Cleaning the machine 32
Cleaning the Nozzle 32
Cleaning method 1: Cleaning the
nozzle via a computer software.
Cleaning method 2: Cleaning the
nozzle without a computer software.
Updating the Firmware 34
Specications 37
Troubleshooting 38
The Machine Does Not Turn On 38
The Software Will Not Install 38
A File Cannot Be Located after
an SD Card Is Inserted 39
Files Will Not Print 40
The Printer Is Not Working 40
Printing Quality Is Not Satisfactory 41
The Filament Does Not
Extrude During Printing 44
The Printed Object Cannot Be
Removed from the Print Bed 44
How to use the manual 3
Symbols used in the manual 3
Legal Notices 4
Model Names 4
Disclaimers 4
Copyright 4
Trademarks 4
FCC (Federal Communications
Commission) 5
FCC WARNING 5
AC Adapter 6
Important safety instructions 7
Supplied Accessories 8
Machine and Installation
Information 9
Installation Space 9
Names of parts 10
Exterior
Interior
Removing the Packing Materials 12
Installing the Software and
Connecting the USB Cable 13
Basic Operation 14
Filament Installation 14
Print Bed Preparation 18
Connecting Power 19
Printing from the Computer 20
Printing from the SD Card 21
Canceling Printing 22
MARV User Manual
3
How to use the manual
Symbols used in the manual
Caution
Caution indicates a potentially hazardous situation that may result in injury to the user
of the machine or others, or the loss of property.
Note
Notes indicate useful tips or additional information for procedures and product use.
[ ]
This symbol represents control buttons on the computer screen and the machine.
e.g., [Import], [OK]
MARV User Manual
4
Legal Notices
Model Names
MARV: MW10EU1, MW10EU2, MW10EU3, MW10EU4, MW10EU5, MW10U1, MW10U2
Disclaimers
The content of the manual is subject to change without prior notice.
CANON KOREA BUSINESS SOLUTIONS INC. MAKES NO WARRANTY OF ANY KIND
WITH REGARD TO THIS MATERIAL, EITHER EXPRESS OR IMPLIED, EXCEPT AS
PROVIDED HEREIN, INCLUDING WITHOUT LIMITATION, THEREOF, WARRANTIES AS
TO MARKETABILITY, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOS OF
USE OR NON-INFRINGEMENT. CANON KOREA BUSINESS SOLUTIONS INC. SHALL
NOT BE LIABLE FOR ANY DIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OR
LOSSES, ARISING FROM OR RELATED TO YOUR USE OF THIS MANUAL.
Copyright
No part of this manual may be reproduced, transmitted, or duplicated in any form or by any
means electronic, mechanical, magnetic, optical, chemical, manual or otherwise, be stored
in a retrieval system, or converted into any computer languages without written permission
from Canon Korea Business Solutions INC.
Trademarks
Microsoft, Windows, Windows XP, Windows 7, Windows 8 and Windows 8.1 are either
registered trademarks or trademarks of Microsoft Corporation in the United States and/or
other countries.
All other brand and product names are trademarks, registered trademarks, or service
marks of their respective companies.
MARV User Manual
5
FCC (Federal Communications Commission)
MARV: MW10U1, MW10U2
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesired operation.
FCC WARNING
Changes or modications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note
This equipment has been tested and found to comply with the limits for a class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of the FCC
Rules. Do not make any changes or modi cations to the equipment unless otherwise speci
ed in this manual. If you make such changes or modi cations, you could be required to stop
operation of the equipment.
CANON KOREA BUSINESS SOLUTIONS INC.
607, Teheran-ro, Gangnam-gu, Seoul, Korea
TEL No.1588-2500
Note
This equipment complies with the Canadian ICES-003 Class B limits.
Respecte les limites de la classe B de la NMB-003 du Canada.
MARV User Manual
6
AC Adapter
Connect only to a power outlet of the rated voltage and power supply frequency
(50/60 Hz depending on your region).
Do not connect other electrical equipment to the same power outlet to which printer is
connected. Also, when using an extension cord, make sure that the extension cord is
rated for the current requirements of the printer.
Never disassemble or modify the AC adapter, as it is dangerous.
The power cord may become damaged if it is often stepped on or if heavy objects are
placed on it. Continued use of a damaged power cord and AC adapter can lead to an
accident, such as a re or electrical shock.
Do not use the power cord while it is coiled.
Do not pull directly on the power cord. When disconnecting the power cord, grasp the
plug and remove it from the outlet.
Keep the area around the power cord clear of objects so that the power cord can be
disconnected easily in an emergency.
Do not use an AC adapter other than the one provided with the printer.
Do not use the AC adapter provided with the printer with other products.
If you have any questions regarding the power supply, contact your local authorized or
service representative for further information.
MARV User Manual
7
Important safety instructions
Please read this entire section before using the machine. These instructions are
intended to prevent any potential damage to the machine and injury to the user
or others. Failure to adhere to these instructions may result in injury to the user or
others, or may cause damage to the machine or operation errors.
Do not install the machine on an unstable surface, such as an unstable shelf or uneven
oor.
Do not damage the power cord or any cables.
Be sure to use the designated voltage only.
Use manufacturer-supplied components and accessories only. We are not liable for
performance degradation, breakdowns, or accidents caused by third-party products.
Using manufacturer-supplied laments is recommended for achieving the best printing
quality. Using third-party laments may result in unsatisfactory printing quality and a
blocked nozzle, and prevent the device from printing at full capacity.
For the best printing results, allow the nozzle to cool down before printing.
Do not shake or cause physical impacts to the machine.
Do not disassemble or modify the machine.
Be sure to turn off the power and disconnect the power cord and cables when moving
the machine.
Do not turn off the power or load or remove the lament during printing.
Do not turn off the software or open machine covers during printing. It can interrupt
printing or cause a system failure.
Do not touch the nozzle during installation, operation, or immediately after the operation
is complete. Doing so may cause burns.
Do not forcefully move or cause physical impacts to the nozzle unit. It may cause the
machine to malfunction or damage the sensors.
Calibrate the gap between the print bed and the nozzle before printing.
Do not insert or drop objects inside the printer (lament, etc.). Doing so may cause re
or damage.
After use, open laments should be sealed and kept in a dry environment and out of
direct sunlight.
Be sure there is adequate lament on the lament before printing.
When printing stops due to a shortage of lament, replace the lament. If a printing job
is discontinued, it cannot be resumed. Before using the machine, check that there is
enough material available on the lament.
MARV User Manual
8
Supplied Accessories
Check that all of the pictured components and accessories are present before
installing the machine. If any items are missing or damaged, contact your retailer.
Note
Use manufacturer-supplied components and accessories only. We are not liable for performance
degradation, breakdowns, or accidents caused by third-party products.
The shape, positioning, and quantity of packing materials may change without prior notice for
quality improvement purposes.
ON
SD CARD
OFF
Machine Print bed Filament
Quick Setup Guide Manual and driver
CD-ROM Adhesive tape
Adapter Power cable USB cable
SD card Nozzle maintenance pin Calibration sheet
Warranty card
MARV User Manual
9
Machine and Installation Information
Make sure there is sufcient space to install the device.
Caution
Do not install the machine on an unstable surface, such as an unstable shelf or uneven oor.
Installation Space
100mm
100mm
850mm
586mm
146mm
357mm
385mm
820mm
MARV User Manual
10
Names of parts
Exterior
ON
SD CARD
OFF
Top cover
LCD
Front
cover
[OK] button
[▼] button
USB port
SD card slot
Power switch Firmware switch
Power plug-in
MARV User Manual
11
Interior
Left cover
Filament mount Print bed
Staging bracket
Nozzle
Feeding
tube
Cable
Filament
insertion lever
Nozzle unit
Filament
insertion hole
MARV User Manual
12
Removing the Packing Materials
1. Remove the orange adhesive tape. Remove the machine's external packing
material.
2. Open the top cover.
3. To open the front cover, press [PUSH] on the right-hand side of the front
cover.
4. Remove the components and packing materials from the inside of the
machine.
Note
When disposing the packing material, take care not to accidentally discard any machine
parts.
When removing components and packing materials,do not move the nozzle unit inside the
machine by force in any means.
It may cause the machine to malfunction or damage sensors.
5. Close the front cover.
Push the front cover in until you hear a click from the right side.
6. Close the top cover.
Push the top cover to make sure it is completely closed.
MARV User Manual
13
Installing the Software and Connecting the USB Cable
The software must be installed to use all MARV functions.
Install the software on your computer using the enclosed CD-ROM.
Note
Supported operating systems
Windows XP 32 bit SP3
Windows 7 (32 bit/64 bit)
Windows 8 (32 bit/64 bit)
Windows 8.1 (32 bit/64 bit)
1. Insert the enclosed CD-ROM into the computer.
2. When the installation software begins, follow the instructions to install the
software.
3. When the software is installed, connect the printer to your computer via the
USB cable.
Caution
You must install the software prior to USB connection.
Flat Connector
Connect to the computer.
Square Connector
Connect to the machine.
MARV User Manual
14
Basic Operation
Caution
The nozzle may become excessively hot during the device installation and printing. Avoid touching
the nozzle. Doing so may cause burns.
Note
It is recommended to use manufacturer-supplied laments to achieve the best printing results.
Using third-party laments may result in unsatisfactory printing quality and nozzle clogging, and
preventing the device from printing at full capacity.
After use, open laments should be sealed and kept in a dry environment and out of direct sunlight.
Straighten any tangled lament on the lament. Tangled lament may cause device malfunctions
and printing errors.
Filament Installation
1. Remove the lament from the package.
2. Remove the tape from the lament package then unwind the lament for
installation.
3. Open the left and top covers.
4. Mount the lament with the lament's label facing front.
Push in the cartridge until you hear a click to make sure that it is xed on the
cartridge mount.
Note
Install the laments so that lament will release in a left direction. If installed in the reverse
direction, the lament may not feed properly.
Left direction
MARV User Manual
15
5. After installing the lament, insert the lament into the feeding tube.
Filament
Feeding
tube
Note
If the end of the lament is deformed or bent, cut it cleanly so that it will t into the insertion
hole in the nozzle.
Push the lament through the feeding tube until it extends approximately 8 cm from the
other end of the feeding tube.
8cm
(appr. 3 inch)
Left & Top covers open
6. While pressing down on the insertion lever of the lament nozzle unit with
one hand, insert the end of the lament into the insertion hole.
Filament
insertion hole
Insertion
lever
MARV User Manual
16
7. Push the lament into the nozzle until it will go no further (about 5 cm).
Refer to the cross section view of a lament being inserted.
Nozzle
Insertion
hole
Roller
Filament
Caution
Nozzle
Insertion
hole
Roller Filament
If the lament is not inserted fully, as shown in the cross section above, the lament may not
feed properly and cause the nozzle to clog or printing failure.
8. Insert the lament fully and push the feeding tube into the insertion hole.
Refer to the cross section view of the feeding tube being inserted.
Nozzle
Insertion hole
Roller
Filament
Feeding
tube
Note
Printing may not work if the lament is not fully inserted into the nozzle unit.
If the end of the lament is deformed or bent, cut it cleanly so that it will t into the insertion
hole in the nozzle.
MARV User Manual
17
9. After inserting the feeding tube, make sure that the feeding tube and the
cable are at the same height.
Feeding
tube
Cable
Note
If the feeding tube is higher or lower than the cable, this may affect printing quality.
10.
Make sure the height of the feeding tube and the cable are the same and
close the top cover.
MARV User Manual
18
Print Bed Preparation
Prepare the adhesive tape and print bed provided with the machine.
Apply the adhesive tape to secure the object to the print bed. For enhanced printing
results, we recommend that you use new tape each time you print an object.
Caution
Install the print bed in the machine before printing.
If tape is not applied to the print bed, the lament will not be secure and may affect printing quality.
Do not forcefully move or cause physical impacts to the machine's nozzle unit. Doing so may cause
the machine to malfunction or damage the sensors.
The nozzle may become excessively hot during the device installation and printing. Avoid touching
the nozzle. Doing so may cause burns.
1. Apply the adhesive tape to the print bed.
Apply the tape evenly over the surface of the print bed to make sure that it does
not overlap.
Note
If the tape is applied unevenly or overlaps, it may cause a nozzle calibration error and affect
printing quality.
Apply tape to the print bed only and not beyond the edges of the print bed.
2. Press [PUSH] to open the front cover.
3. Insert the print bed with the adhesive tape facing upwards.
Place the print bed on the left and right staging brackets and push the print bed
until it meets the back of the machine.
Caution
Insert the print bed securely on the left and right staging brackets. Failure to do so may result in an
uneven printing bed.
MARV User Manual
19
4. Close the front cover.
Push in the front cover until you hear a click.
Connecting Power
After installing the print bed, refer to the instructions below and connect the adapter
and power cable. Then, turn on the power.
Caution
Do not damage the power cord or any cables.
Be sure to use the designated voltage only.
Use manufacturer-supplied components and accessories only. We are not liable for performance
degradation, breakdowns, or accidents caused by third-party products.
1. Assemble power cable.
2. Connect MARV to an electric outlet.
ON
SD CARD
OFF
3. And then turn on the power.
After the power is on, the LCD screen turns on and the machine starts to
initialize. After the initialization is complete, [MARV is Ready] appears on the
screen.
MARV User Manual
20
Printing from the Computer
Print settings can be changed using the MARV software installed on the computer.
For more information about the functions of the MARV software, refer to 'Using the
MARV Software' on P.24.
Caution
If the computer enters Sleep Mode during printing, printing stops. If a print job stops, it cannot
resume. Sleep Mode should be turned off or adjusted before printing an object. It is recommended
that Sleep Mode on the computer be disabled before running the MARV software.
1. Click [Open] in the software window.
2. Click .stl le to print.
3. To edit the le click [Edit].
For more information about the [Edit] menu, refer to 'Editing functions' on P.26.
4. Click [Save].
Select an extension, enter a lename, and save the le. (If you print from the
machine using an SD card, select the .marv extension.)
5. Click [Settings] to designate the output settings.
For more information about the [Settings] menu, refer to 'Settings' on P.27.
6. Click [Print].
When the nozzle is heated, printing begins. (nozzle preheating time:
approximately 3 minutes)
Note
When an object is printed, the nozzle moves to the edge of the print bed and discharges a small
quantity of lament and then continues printing. When the object is printed, remove the object
and the discharged lament.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45

Marv MW10EU2 User manual

Category
Print & Scan
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI