Low Range Off-Road LROR-305815 Installation Instructions Manual

Brand
Low Range Off-Road
Model
LROR-305815
Type
Installation Instructions Manual
Suggested Tools:
•Floor Jack (or Twin Post Lift)
•2 Jack Stands (or Under-hoist
Safety Stand)
•Sockets 14, 17, 19 & 22 mm
•Ratchet
•Combination wrench, 19mm
•Large Adjustable Groove Pliers
•Plastic tipped (or brass) Hammer
•Large Tapered Punch
•White (or yellow) Metal Marker
•Ratchet strap
CAUTION: Safety glasses should be
worn at all times when working with
vehicles and related tools and
equipment.
Installation Instructions
LRT 3/1 Leveling/Lift Kit for 2005-2016 Toyota Tacoma (LR-LRTACO)
LRT 3/2 Leveling/Lift Kit for 2016+ Toyota Tacoma (LROR-305815)
General Note"
These instructions are written for use with a floor jack and jack
stands. However, they can be easily adapted to the use of a
twin post lift.
Caution"
This vehicle will require a professional wheel alignment after the leveling/lift kit has
been installed. Failure to have this vehicle professionally aligned could result in poor
vehicle stability, handling, and braking; as well as excessive tire tread wear. Further,
certain aspects of this installation can be dangerous. Therefore, we recommend that a
Step 1"
Lift the front of the vehicle with a floor
jack and support it with (2) jack stands.
Place the jack stands under the frame
just behind the front wheels. Safety
stands should always be positioned on a
sturdy part of the frame that is
horizontal.
Caution:"
You should never work on a vehicle
that is supported by any kind of a
jack without the added protection of
jack stands. The vehicle can easily
slip from the jack and cause serious
bodily injury and or vehicle damage.
Always use jack stands.
Step 3"
Remove the skid plate by removing (4)
bolts using a 14 mm socket.
Step 2"
Remove the 2 front wheels and set them
aside.
Step 3"
Disconnect air intake air duct.
Step 4"
Remove air intake case nut using a
10mm socket.
Step 2"
Disconnect a second vacuum tube from
air intake case using a standard
screwdriver as shown.
Step 3"
Disconnect air intake air duct.
Step 4"
Remove air intake case nut using a
10mm socket.
Step 2"
Disconnect a second vacuum tube from
air intake case using a standard
screwdriver as shown.
Step 3"
Disconnect air intake air duct.
Step 4"
Remove air intake case nut using a
10mm socket.
Step 2"
Disconnect a second vacuum tube from
air intake case using a standard
screwdriver as shown.
Step 3"
Disconnect air intake air duct.
Step 4"
Remove air intake case nut using a
10mm socket.
Step 2"
Disconnect a second vacuum tube from
air intake case using a standard
screwdriver as shown.
Step 3"
Disconnect air intake air duct.
Step 4"
Remove air intake case nut using a
10mm socket.
Step 2"
Disconnect a second vacuum tube from
air intake case using a standard
screwdriver as shown.
Step 3"
Disconnect air intake air duct.
Step 4"
Remove air intake case nut using a
10mm socket.
Step 2"
Disconnect a second vacuum tube from
air intake case using a standard
screwdriver as shown.
Step 3"
Disconnect air intake air duct.
Step 4"
Remove air intake case nut using a
10mm socket.
Step 2"
Disconnect a second vacuum tube from
air intake case using a standard
screwdriver as shown.
Step 3"
Disconnect air intake air duct.
Step 4"
Remove air intake case nut using a
10mm socket.
Step 2"
Disconnect a second vacuum tube from
air intake case using a standard
screwdriver as shown.
Step 3"
Disconnect air intake air duct.
Step 4"
Remove air intake case nut using a
10mm socket.
Step 2"
Disconnect a second vacuum tube from
air intake case using a standard
screwdriver as shown.
Step 3"
Disconnect air intake air duct.
Step 4"
Remove air intake case nut using a
10mm socket.
Step 2"
Disconnect a second vacuum tube from
air intake case using a standard
screwdriver as shown.
Step 3"
Disconnect air intake air duct.
Step 4"
Remove air intake case nut using a
10mm socket.
As always, If you experience any difficulty during the installation of this product
please contact Low Range Off-Road Technical Support at 801-805-6644 M-F
8am-5pm MST. Thank you for purchasing from Low Range Off-Road.
These instructions are designed as a general installation guide. Installation of many Low Range
Off-Road require specialized skills such as metal fabrication, welding and mechanical trouble
shooting. If you have any questions or are unsure about how to proceed, please contact our shop
at 801-805-6644 or seek help from a competent fabricator. Using fabrication tools such as
welders, torches and grinders can cause serious bodily harm and death. Please operate equipment
carefully and observe proper safety procedures.
Rock crawling and off-road driving are inherently dangerous activities. Some modifications will
adversely affect the on-road handling characteristics of your vehicle. All products sold by Low
Range Off-Road are sold for off road use only. Any other use or application is the responsibility
of the purchaser and/or user. Some modifications and installation of certain aftermarket parts may
under certain circumstances void your original dealer warranty. Modification of your vehicle may
create dangerous conditions, which could cause roll-overs resulting in serious bodily injury or
death. Buyers and users of these products hereby expressly assume all risks associated with any
such modifications and use.
Revised 06/21/12 © Copyright 2012 Low Range Off-Road, LC!!!!! All Rights Reserved
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Low Range Off-Road LROR-305815 Installation Instructions Manual

Brand
Low Range Off-Road
Model
LROR-305815
Type
Installation Instructions Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents