Trim Kit
Part Number AWSTK24
INSTALLATION
INSTRUCTIONS
WINE DISPENSING SYSTEM MODEL: DYWS4
Part No. 107554 Rev. A
Parts Included with kit
Bottom left trim
bracket
Top trim bracket
Foam Strips
(1 long, 2 short)
Bottom right trim
bracket
Right trim
piece
Left trim
piece
Top trim
piece*
*The top and bottom trim pieces are identical, but
installed in the opposite orientation from each other.
Bottom
trim piece*
(8) #8 x 3/8 Phillips
head screws (PN 83263)
(9) #10 x 1/2 Phillips
head screws (PN 83022)
(1) Base divider
(2) Base supports
(8) Flat head Phillips head
screws (PN 107578)
(8) Fiber washers
(PN 83555)
IMPORTANT: The wine dispensing utilizes a thermo-electric cooling system that can normally
cool the bottle bay to a temperature 25°F less than the ambient air outside the unit. This trim kit
limits system air circulation slightly, limiting the cooling capability to 22°F less than ambient. Be
sure that this limitation is acceptable before installing this kit.
Wine Dispensing System Trim Kit Instructions
Page 2
For proper fit, the cutout dimensions
shown are required. The spacing above
and below the cutout are critical for
ventilation purposes. Failure to provide
proper ventilation will result in poor wine
cooling. Consult the Wine Dispensing
System Installation Instructions
for additional cabinet requirements
(electrical requirements etc.).
Introduction
Tools Required
Phillips head
screwdriver
PencilTape measure
Drill with 3/32” drill bit
(for drilling pilot holes)
29”
(73.7 cm)
1 5/8” min.
(4.1 cm)
both sides
21”
(53.3 cm)
24” min.
(61.0 cm)
1 1/2” min.
(3.8 cm)
1 1/2” min.
(3.8 cm)
Wine Dispensing System Trim Kit Instructions
Page 3
STEP 1 Peel the protective backing off of the longest of the 3 foam strips and at-
tached it to the base divider as shown.
Installation Instructions
Foam strip
Base Assembly
STEP 2 Attach the (2) base pieces to the base divider using (4) #8 x 3/8 screws. The
foam strip attached in step 1 goes toward the base pieces as shown below.
Wine Dispensing System Trim Kit Instructions
Page 4
STEP 3 Insert the base assembly, assembled in step 1, into the cutout with the divider toward
the back. Center it left to right in the cutout using a ruler or tape measure.
STEP 4 Using a pencil, mark 4 pilot hole locations in the front of the cabinet.
STEP 5 Drill 4 pilot holes for the base assembly using a 3/32” drill bit.
STEP 6 Attach the base assembly to the front of the cabinet using (4) #10 x 1/2 Phillips head
screws.
Base assembly
(divider toward back)
Cutout
Base Installation
Wine Dispensing System Trim Kit Instructions
Page 5
Base
assembly
Bottom left
trim bracket
Bottom right
trim bracket
STEP 7 Attach the bottom left and bottom right trim brackets to the front of the base assembly
as shown, using (4) #8 x 3/8 screws.
STEP 8 Attach the bottom left and bottom right trim brackets to the front of the cabinet using
(2) #10 x 1/2 Phillips head screws.
Bottom Trim Bracket Installation
Attach Bottom Trim Brackets to Cabinet
Wine Dispensing System Trim Kit Instructions
Page 6
STEP 9 Hold the top trim bracket in the mounting position on the top edge of the cut-
out. Center it using a ruler or tape measure
STEP 10 While holding the trim bracket in place, using a pencil, mark 3 pilot hole loca-
tions in the underside of the top of the cabinet cutout.
STEP 11 Drill 3 pilot holes for the top trim bracket using a 3/32” drill bit.
STEP 12 Attach the top trim bracket to the top front of the cabinet using (3) #10 x 1/2
Phillips head screws.
Top trim
bracket
Cutout
Top Trim Bracket Installation
Wine Dispensing System Trim Kit Instructions
Page 7
1 Inch
(2.5 cm)
1 Inch
(2.5 cm)
1 Inch
(2.5 cm)
Foam strip,
2 places
STEP 13 With the help of at least one other person, place the wine dispensing system
close the the cabinet cutout. Connect the power supply and the gas supply
line according to the Wine Dispensing System Installation Instructions. Ad-
just the leveling legs to 1 inch in height. NOTE: The trim and the wine dispens-
ing system will not line up properly if the legs are not adjusted to 1 inch.
STEP 14 Peel the protective backing off of the short foam strips included with the kit
and attached them to the sides of the wine dispensing system at the bottom of
the side panel. Leave a 1 inch gap between the front of the unit and the edge
of each foam strip (see below).
STEP 15 With the help of at least one other person, lift the wine dispensing system into
the cutout. Be sure that the foam strips on the sides do not pull loose. The
legs on the wine dispensing system go on top of the base supports.
STEP 16 Center the wine dispensing system left to right in the cutout using a ruler or
tape measure. The front of the system needs to protrude from the front of the
cabinet 1 inch.
WARNING: Excessive weight hazard - Use two or more people to move and install the wine
dispensing system. Failure to do so can result in back or other injury.
Foam Strip Installation - Step 14
System Installation - Steps 15 and 16
Dacor ● 14425 Clark Avenue, City of Industry, CA 91745 ● Phone: (800) 793-0093 ● Fax: (626) 403-3130 ● www.dacor.com
STEP 14 Assemble the front trim pieces as shown below. Insert the tabs on the top and
bottom pieces into the slots on the side pieces.
STEP 15 Install the trim using the (8) at head screws included with the kit. Insert the
ber washers between the trim and the mounting brackets as needed for a
good t.
Trim Assembly and Installation
Insert tabs
into slots
Flathead screw,
8 places
Fiber washers,
use as necessary
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Dacor DYWS4 Installation guide
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Jenn-Air JUC2450ARB User manual
-
GE ZISB48DC Installation guide
-
GE ZISW48D Installation guide
-
GE ZIS420NR User manual
-
GE ZISW420D Installation guide
-
Monogram ZISP480DKSS Operating instructions
-
GE ZISS360DMSS Installation guide
-
U-Line U2224BEVINT60B User guide
-
GE ZISW360DM Installation guide
-