Danfoss DEVIreg 535 Easy User guide

Brand: Danfoss

Model: DEVIreg 535 Easy

Type: User guide

Danfoss DEVIreg 535 Easy is a programmable thermostat designed to work with underfloor heating systems. It allows you to set different temperature profiles for different times of the day and days of the week, ensuring a comfortable and energy-efficient heating solution.

With DEVIreg 535 Easy, you can select between four pre-defined timer programs (P1-P4) or create your own custom program to meet your specific needs. The thermostat also features a manual mode (P1) that keeps the heating on constantly at a set temperature.

The thermostat is easy to install and use, with a clear and intuitive user interface. It features a large backlit display that shows the current temperature, time, and program settings. The installation process is guided by on-screen instructions, making it quick and straightforward.

Setting up your Devireg 535 programmable thermostat with

your devimat system

Devireg 535

Selection of sensor type

Power on the thermostat

With the front o, with

a small screwdriver

or pencil press the

installation button.

Select the oor sensor

To change the default setting, press

l and use the arrow buttons  to

select your choices. Press l to accept

your choice.

Press  for the next setting.

Maximum oor temperature.

- Tiles on timber based oor = 29°C

- Tiles on concrete based oor = 40°C

- Timber covered oors = 27°C

(parquet etc. - Please check with

oor supplier).

To change this setting, press l and

use the arrow buttons  to select

your choice. Press l to accept your

choice.

Press  for the next setting.

Scale

When selecting Celsius, the display

will show the actual temperature at

the oor sensor.

To change this setting, press l and

use the arrow buttons  to select

your choice.

Press l to accept your choice.

The installation procedure is now nished.

You can use the  for going back or forward through

the settings, otherwise:

Press the installation pinhole to exit

installation mode.

Put the frame and front back on.

You enter the settings by pressing the

pinhole with a small screw driver,

pencil, the display now changes from

temperature to time display.

By pressing the l, the hours starts

ashing - you can now change them

with the .

Press the l again to change the

minutes with the .

To nish, press l then 

Setting the time

Setting the weekday

Mon Tue Wed Thu Fri Sat Sun

By pressing the l, the weekday starts

ashing - you can now change them

with the .

Press the l to accept.

To nish press 

Setting the timer periods

The rst period bar ashes

indicating this is the morning period.

By pressing the l, the start time of

the period starts ashing. You can

change it with the arrow buttons

 in increments of 15 minutes.

Press the l to accept.

The second (day), third (evening) and

fourth (night) period bars are set as

mentioned above.

Setting the comfort temperature

By pressing the l, the preset comfort

temperature starts ashing.

You can change it with the arrow

buttons 

Press l to accept, then press 

Setting the set back temperature

(second and fourth period)

By pressing the l, the preset comfort

temperature starts ashing, normally

this is set to OFF.

You can change it with the arrow

buttons 

Press l to accept.

Then press the pinhole with a

small screwdriver or pencil.

Changing timer program

To change the program:

Keep the l button pressed for 2

seconds.

The actual program starts to flash.

It is now possible to change the

program by using the buttons 

Press the l to accept.

P1 - Manual mode

On constantly 24 hours 7 days a week

at set temperature.

Set temperature - twice a day.

Set temperature all day.

Set temperature Monday - Friday

twice a day.

Saturday - Sunday all day.

Part no.: 001v01 07.04.2011

Danfoss DEVIreg 535 Easy User guide

Danfoss DEVIreg 535 Easy User guide

Danfoss DEVIreg 535 Easy User guide

Related papers

Other documents