DKS Traffic Signal 115 VAC (Obsolete) User manual

Type
User manual
Support
Post
Bracket
Bracket
Cover
U-Bo
lt
Clamp
U-Bolt
Clamp
Route wire
through
conduit.
Support Post Assembly
Use existing
circuit board
bracket bolts
to moun
t
support post
bracket.
Drill 7/8” hole
centered where
elbow touches
operator housing
(Approximately 18” down
from the top of operator).
Secure 3/4” conduit nipple
in drilled hole with
conduit nut .
2” conduit nut to secure elbow.
Use 2” conduit
nuts to secure
traffic light
assembly to
support post.
Route wire through
support post.
Traffic Light
Assembly
2” Elbow
Shut off AC power to operator.
Turn off DC power switch on certain models.
This kit is designed for the 1600 model barrier gate operators. Recommended for the 1603 auto spike system. The traffic signal is
synchronized with the gate operator’s up/down cycle. The red light stays on and only changes to green when the operator’s arm is
fully raised.
2” Threaded Elbow
2” Conduit Nut (3)
5/8” Cover Bracket
bolt and lockwasher
(2 sets)
3/4” Conduit Nipple
and Conduit Nut
U-Bolt Clamp with
lockwashers and nuts
(2 sets)
Kit Includes:
Plastic Traffic Light Assembly (Factory wired)
2” Threaded Support Post
Support Post Bracket
Bracket Cover.
Hardware:
TRAFFIC LIGHT AND MOUNTING KIT
Installation
DoorKing Part Number
1603-210
Assemble Support Post Mount Support Post Assembly to Operator
Support Post
1 2
120 S. Glasgow Avenue
Inglewood, California 90301 U.S.A.
M
o
ving Gate Can C
a
use
Serious Injury or Deat
h
K
E
E
P C
LEAR
!
G
a
te may
move a
t
any
t
im
e
wi
t
ho
u
t
prior wa
rnin
g.
Do
not
l
et
c
h
il
dren
op
era
te
t
he
gate
or p
lay
in
t
he
g
at
e
ar
ea
.
Th
is ent
r
an
c
e
is
fo
r
ve
hicles
o
nl
y
.
Pedes
t
r
i
an
s
mu
s
t
us
e
se
parate e
nt
r
ance.
Note: This light has been designed to wire to operators that use 115 volt power
and a FORM C dry relay contact that activates when the operator is fully open.
1603-265-C-8-16
DoorKing Part Number
1603-210
Copyright 2016 DoorKing, Inc. All rights reserved.
Wire Traffic Light to Operator
3
120 S. Glasgow Avenue
Inglewood, California 90301 U.S.A.
REVERSE
SENSITIVITY
TIME
DELAY
POWER
1
ON
2 3 4 5 6 7 81
ON
2 3 4 5 6 7 8
NC NO
UP
LOOP
DOWN
LOOP
1234567891011121314
SW 1
SW 2
Chassis Ground
ON
OFF
AC POWER DC POWER
ON
AUTO
DOWN
UP
OFF
NEU HOT
Red Wire (Com)
Brown Wire (N.O.)
Note: To reverse
light sequence
change to N.C.
(Ground) Green Wire
(Neutral) White Wire
(Hot) Black Wire
3/4” Conduit nipple
installed in operator housing.
Circuit Board
Bracket Bolt
Circuit Board
Bracket Bolt
Traffic Light Terminal
Red Relay Com
Brown Relay N.O.
White 115V Neutral
Black 115V Hot
Green Ground
115 VAC
DANGER
HIGH VOLTAGE!
Keep wire clear of all moving parts.
Circuit Board Bracket
NONCC
See installation on previous page
  • Page 1 1
  • Page 2 2

DKS Traffic Signal 115 VAC (Obsolete) User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI