Support
Post
Bracket
Bracket
Cover
U-Bo
lt
Clamp
U-Bolt
Clamp
Route wire
through
conduit.
Support Post Assembly
Kit P/Ns 1603-222 & 1603-223
Use existing
circuit board
bracket bolts
to moun
t
support post
bracket.
Drill 7/8” hole
centered where
elbow touches
operator housing
(Approximately 18” down
from the top of operator).
Secure 3/4” conduit nipple
in drilled hole with
conduit nut .
Approx 18”
2” conduit nut to secure elbow.
Use 2” conduit
nuts to secure
traffic light
assembly to
support post.
Route wire through
support post on kits
1603-222 and 1603-223.
LED Traffic Light
Assembly
2” Elbow
Shut off AC power to operator.
Turn off DC power switch on certain models.
These kits are designed for the 1600 model barrier gate operators. Recommended for the 1603 auto spike system. The traffic signal
is synchronized with the gate operator’s up/down cycle. The red LED light stays on and only changes to the green LED when the
operator’s arm is fully raised.
2” Threaded Elbow
2” Conduit Nut (3)
5/8” Cover Bracket
bolt and lockwasher
(2 sets)
3/4” Conduit Nipple
and Conduit Nut
U-Bolt Clamp with
lockwashers and nuts
(2 sets)
12 VDC Transformer
Traffic Light
Assembly
6 or 11 Ft
Cable
Kits Include:
Support Post Hardware:
Kit P/Ns 1603-222 & 1603-223
LED TRAFFIC LIGHT AND MOUNTING KIT
Installation
DoorKing Part Numbers
1603-223
11 Ft Cable/95” Post
1603-222
6 Ft Cable/35” Post
1603-221
6 Ft Cable/No Post
Assemble Support Post Mount Support Post on OPPOSITE Side of
Access Door
Sup
port Post (35” or 95”
)
1 2
M
oving Gate C
an Cause
Serious Injur
y or Death
K
E
E
P CLE
A
R!
Ga
t
e
may
mo
v
e at an
y
t
i
me
without
pr
i
or
war
ni
ng
.
Do
no
t
l
et
childr
en
oper
at
e
t
he
ga
t
e
or
pl
ay
in t
he
gat
e
ar
ea
.
Th
is
en
tran
c
e
i
s
f
or
v
eh
i
cles
onl
y
.
Pedest
r
ian
s
mu
s
t
us
e s
epar
at
e entranc
e.
Elbow
Conduit
Nipple
Make sure traffic
light is clear of
raised arm.
Access Door
2”
conduit
nuts
DoorKing Part Numbers
1603-223
11 Ft Cable/95” Post
1603-222
6 Ft Cable/35” Post
1603-221
6 Ft Cable/No Post
1603-264-D-10-20
Copyright 2020 DoorKing
®
, Inc. All rights reserved.
Wire LED Traffic Light to Operator
3
120 S. Glasgow Avenue
Inglewood, California 90301 U.S.A.
REVERSE
SENSITIVITY
TIME
DELAY
POWER
1
ON
2 3 4 5 6 7 81
ON
2 3 4 5 6 7 8
NC
UP
LOOP
DOWN
LOOP
1234567891011121314
SW 1
SW 2
ON
OFF
AC POWER DC POWER
ON
AUTO
DOWN
UP
OFF
3/4” Conduit nipple
installed in operator housing.
Traffic Light Terminal
Red
Red (NC)
6 or 11 Ft Cable
6 or 11 Ft Cable
Green
Green (NO)
Black
Black
(+)
White (-)
to Common
Keep wire clear of all moving parts.
Circuit Board Bracket
NONCC
Existing
Bracket
Bolts
Existing
Bracket
Bolts
12 VDC
Arm Relay Contacts
C - Common - BLACK Wire
NC - RED Wire (Red LED)
NO - GREEN Wire (Green LED)
1601-010
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
DKS Traffic Signal 12 VDC User manual
-
-
-
DKS 1601/1602 User manual
-
-
-
-
-
-
