CTC Union FSW3224 User manual

Version 1.01

2006/01

CTC Union Technologies Co., Ltd.

USER MANUAL

FSW3224

24 + 2G

Web Smart Switch

24+2G Web Smart-switch User Manual

Revision 1.0- 2

1. GETTING START.............................................................................................................................................7

1.1 CONNECTING TO THE SWITCH CONSOLE PORT.....................................................................7

1.2 PC COM PORT SETTING ............................................................................................................7

1.3 CONNECTING TO THE SWITCH WEB PORT..............................................................................7

1.3.1 Advantage of Web Smart Switch..................................................................................8

2. OPERATION NOTICE..............................................................................................................................9

2.1. CONSOLE FUNCTION KEYS .........................................................................................................9

2.2. CONSOLE ACTION ITEM...............................................................................................................9

3. LOGIN..........................................................................................................................................................10

3.1. POWER-ON SELF TESTING........................................................................................................10

3.2. CONSOLE LOGIN.........................................................................................................................10

3.3. WEB LOGIN..................................................................................................................................11

3.3.1. Setting IP Address by Console Port..........................................................................11

3.3.2. Login with a Web Brower........................................................................................... 12

4. CONSOLE USER INTERFACE........................................................................................................... 12

4.1. MAIN MENU...................................................................................................................................12

4.2. PORT STATUS ................................................................................................................................14

4.3. PORT CONFIGURATION..............................................................................................................14

4.4. TRUNK CONFIGURATION...........................................................................................................15

4.5. VLAN CONFIGURATION............................................................................................................16

4.5.1. VLAN Mode: Port-based VLAN................................................................................ 17

4.5.2. Port-based VLAN Group <Add>/<Edit>Menu .................................................... 18

4.5.3. VLAN Mode: 802.IQ VLAN....................................................................................... 19

4.5.4. 802.IQ VLAN Group <Add>/ <Edit> Menu ......................................................... 19

4.5.5. Advanced 802.1Q VLAN Configuration.................................................................. 20

4.6. PORT MONITORING CONFIGURATION....................................................................................20

4.7. QOS CONFIGURATION...............................................................................................................21

4.8. BANDWIDTH CONTROL..............................................................................................................21

4.9. MISC OPERATION........................................................................................................................22

4.9.1. Advanced Switch Configuration ............................................................................... 23

4.9.2. Password Setting......................................................................................................... 24

4.9.3. Restore System Default Setting ................................................................................. 24

4.9.4. Reboot System.............................................................................................................. 24

4.9.5. System Information..................................................................................................... 25

4.9.6. Update Firmware........................................................................................................ 25

24+2G Web Smart-switch User Manual

Revision 1.0- 3

4.9.7. IP Configuration......................................................................................................... 26

5. WEB USER INTERFACE......................................................................................................................27

5.1. WELCOME PAGE..........................................................................................................................27

5.2. MAIN MENU..................................................................................................................................27

5.3. PORT STATUS ................................................................................................................................27

5.4. PORT CONFIGURATION..............................................................................................................28

5.5. TRUNK CONFIGURATION...........................................................................................................29

5.6. VLAN CONFIGURATION............................................................................................................30

5.6.1. VLAN Mode: Port-based VLAN................................................................................ 31

5.6.2. Port-based VLAN Group <Add> / <Edit> Menu................................................. 31

5.6.3. VLAN Mode: 802.1Q VLAN ...................................................................................... 32

5.6.4. 802.1Q VLAN Group <Add> / <Edit> Menu........................................................ 32

5.6.5. Advanced 802.1Q VLAN Configuration.................................................................. 33

5.7. QOS CONFIGURATION...............................................................................................................35

5.8. BANDWIDTH CONTROL..............................................................................................................35

5.9. MISC OPERATION........................................................................................................................36

5.9.1. Advanced Switch Configuration ............................................................................... 37

5.9.2. Password Setting......................................................................................................... 37

5.9.3. Restore System Default Setting ................................................................................. 38

5.9.4. Reboot System.............................................................................................................. 38

5.9.5. IP Configuration......................................................................................................... 39

5.10. LOGOUT...................................................................................................................................39

APPENDIX A........................................................................................................................................................40

24+2G Web Smart-switch User Manual

Revision 1.0- 4

1. Introduction

24+2G SMART is a high performance switch that provides users with 24

10/100Mbps Ethernet and 2 1000Mbps Gigabit ports. The Gigabit module, which can

be copper or fiber media, supports 1000BASE-SX, 1000BASE-LX or 1000BASE-T,

allowing users to increase their network response time at gigabit speeds and with

great flexibility. A RS-232 serial port provides an easy way for installation and

initial set-up.

Non-blocking and maximum wire speed performances are designed on all ports. The

Switch not only supports Auto-Negotiation, but also Auto-MDIX function on all

switched 24 10/100M RJ-45 ports and two Gigabit Copper ports in both half or full

duplex mode. The Auto-MDIX function makes it convenient for the user, because it

eliminates cabling issues.

The Switch also supports both port-based VLAN and Tag-based. To increase

bandwidth application, it supports 7 groups with up to 4 ports Trunk, and moreover,

these trunk ports provide fair-over function to provide back up when one or more

ports malfunction.

Totally front access design and full LED status display ease user’s installation and

inspection and maintenance efforts at rackmount environments. The extra LED

display reflecting the fan status allows for quick diagnosis of over-heat issues.

1.1. Unpacking

Open the shipping carton of the Switch and carefully unpack its contents, the carton

should contain the following items:

l One 24+2G, 24 port Fast Ethernet Smart Switch.

l Mounting Kit: 2 mounting brackets and screws

l Four rubber feet with adhesive backing.

l One AC power cord.

l One RS-232 cable

l This Quick Installation Guide and CD.

24+2G Web Smart-switch User Manual

Revision 1.0- 5

1.2. Installation

Follow the guidelines below to install the Switch.

l Do not place any object weighted more than 3Kg (6.6 lb) on the Switch.

l Connect the power cord to the Switch and the power outlet.

l Leave at least 10 cm (4 inches) of space around the Switch for heat dissipation.

Desktop or Shelf Installation:

When installing the Switch on the desktop or shelf, please attach the rubber feet to the

Switch. Peel off the protective paper on the pads and attach them on the bottom of the

Switch (one at each corner).

Rack Installation:

The 24+2G Switch is rack-mountable and you can install the Switch on an EIA-19

inch equipment rack. To do this, first install the mounting brackets on the Switch’s

side panels (one on each side), secure them with the included screws, and then use the

screws provided with the equipment rack to mount the Switch on the rack.

Power On the Switch:

The 24+2G Switch has a universal power supply and you can power up the Switch

with 90 ~ 260V AC, 50 ~ 60Hz power source. The AC power cord connector is

located at the rear of the unit and the On/Off switch is next to the connector. Connect

the power cord from the power outlet to the Switch and push the On/Off Switch to

“ON” position to power on the Switch. After the Switch is powered on, it will

perform “self-diagnostic” (POSD). This process takes about 20 seconds to complete,

during this process, the “DIAG” LED will blink green and the Switch will not

response to any configuration program and all the connections to the Switch will not

be available. When the processed is completed, the “DIAG” LED will stay solid

green.

Below is a table that describes the meaning of each LED indicator.

24+2G Web Smart-switch User Manual

Revision 1.0- 6

LED indicators information

Status

LED

Color

Solid Blinking

Power Green Power is applied to this device N/A

DIAG Green Self diagnostic successful

Performing self diagnostic

(after Power On)

Cooling

Fans

FAN Red Left cooling fan failed

N/A

LINK/ACT

(1 ~24 port)

Green

10Mbps Ethernet connection speed

TX/RX activity or

Collision

Green

100Mbps Fast Ethernet connection speed

N/A

100M

(1 ~24 port)

Off 10Mbps connection speed N/A

10/100/1000Mbps Copper Gigabit Port (Optional Module)

Top LED Orange 100Mbps Fast Ethernet connection

speed (with Middle LED off)

N/A

Middle LED Green 10Mbps Ethernet connection.

(with Top LED off)

N/A

Bottom LED Green

N/A

TX/RX activity or

collision

Top+Middle

LEDs

Orange

+ Green

1000Mbps Gigabit connection speed N/A

24+2G Web Smart-switch User Manual

Revision 1.0- 7

2. Getting Start

2.1. Connecting to the Switch Console Port

l Users can use a RS-232 non-crossover serial cable to connect the PC’S COM port to the switch

console port.

l The switch system provides the RS-232 interface with baud rate 9600-8-n-1.

l Use terminal emulation program ( e.g. Windows HyperTerminal, NetTerm) to configure the

switch system.

Notice: When using HyperTerminal with Microsoft Windows 2000, ensure that you have

Windows 2000 Service Pack 2 or later version was installed. With Windows Service Pack 2, the

arrow keys function properly in HyperTerminal’s VT100 emulation.

2.2. PC COM Port Setting

l Baud rate= 9600

l Data bits= 8

l Parity= None

l Stop bits= 1

l Flow control= None

2.3. Connecting to the Switch Web Port

l Users can use a CAT-5 cable to connect the PC’s LAN port to one of the switch Ethernet port.

l Use web browser program (e.g. Internet Explorer, Netscape…) to configure the switch system.

Switch System

CAT-5 cable

Switch System

24+2G Web Smart-switch User Manual

Revision 1.0- 8

2.3.1. Advantage of Web Smart Switch

l No proprietary program, no installation, no learning. It’s the most painless way for IT/MIS

person to use,

l Cross-platform support. You could configure the switch by web browser on any platform (e.g.

Windows ME, Windows XP, Windows Server 2003, UNIX, Linux, Macintosh…).

l Router awareness, real remote control. You could configure the switch from a remote PC that

across a router.

l Unicast management, no broadcast management packets. Only the switch that you want to

manage is involved in, no broadcast packets noise all over the network.

24+2G Web Smart-switch User Manual

Revision 1.0- 9

3. Operation Notice

3.1. Console Function Keys

The following generic function keys provide functon in all of the menus:

Key Fuction

Tab/ Move the cursor to right item.

Backspace/ Move the cursor to left item.

Move the cursor to up item.

Move the cursor to down item.

Toggle selected item to next configuration

Select action.

Back to previous status.

3.2. Console Action Item

The following generic action items provide functon in all of the menus:

Key Fuction

Quite Exit this page and return to previous menu.

Edit Configure all items. Press ”Enter” key will set configure

and press “Esc” key will go back to action menu line.

Save Save the configuration that you had changed.

Page Up Back to previous page.

Page Down Go to next page.

24+2G Web Smart-switch User Manual

Revision 1.0- 10

4. Login

4.1. Power-On Self Testing

When the power is supplied to the switch system, power-on self testing is running. The result of

power-on self testing is output to the console port. Each diagnostic item has either “Passed” or

“Failed” result. If one of the diagnostic items failed, the whole initialization procedure will stop.

4.2. Console Login

When you connect to the switch with a terminal emulation program, a login screen is displayed. Enter

a user name and password to login to access the switch.

Item Option Default Value

Username Max:6, Min:1 characters, case sensitive web

Password Max:6, Min:1 characters, case sensitive smart

24+2G Web Smart-switch User Manual

Revision 1.0- 11

4.3. Web Login

4.3.1. Setting IP Address by Console Port

When you are going to login to the web pages, you have to set the IP address properly first. You could

login with the default IP address: 192.168.1.1. But you have to make sure this IP could work in your

network environment. Or, you have to re-configure the IP address, subnet mask and default gateway.

First login with the console port

Second, go to the Main Menu\ Misc Operation\ “IP Configuration” screen. Then, set the IP address

properly.

24+2G Web Smart-switch User Manual

Revision 1.0- 12

4.3.2. Login with a Web Brower

When you connect to the switch with a web browser, a login screen is displayed. Enter a user name

and password to login to access the switch.

Items Option Default Value

Username Max: 6, Min:1 characters, case sensitive web

Password Max: 6, Min:1 characters, case sensitive smart

5. Console User Interface

5.1. Main menu

This is the main menu of the switch console software.

Item Description

Port Status

Display current status: enabled/disabled, link up/down, speed/duplex and

flow control of each port.

Port Configuration Configure enable state, speed/duplex, and flow control for each port

Trunk Configuration Configure the trunk groups.

VLAN Configuration Configure the VLAN groups

1. VLAN Mode Configuration

2. Advanced 802.IQ VLAN Configuration

Port Monitoring Configuration Configure port monitoring.

QoS Configuration Configure QoS mode, 802.1p priority and static port priority.

Bandwidth Control Configure input rate or output rate of each port.

Misc Operation Miscellaneous Operation

1. Advanced Switch Configuration

2. Password Setting

3. Restore to Default Configuration

4. Reboot System

24+2G Web Smart-switch User Manual

Revision 1.0- 13

5. System Information

Logout Logout and login menu.

24+2G Web Smart-switch User Manual

Revision 1.0- 14

5.2. Port Status

Display current status: enabled/disabled, link up/down, speed/duplex and flow control of each port.

Item Description

Enable Enable / Disable

Link Status Up/Down.

If the port was disabled, the item is displayed as “---“ .

Spd / Dpx 100F/ 100H/ 10F/ 10H.

F: Full duplex, H: Half duplex.

If the port was disabled or link sown, the item is displayed as “---“ .

Flow Control On / Off

If was port disabled or link sown, the item is displayed as “---“ .

Special item in the Action Menu:

<Refresh>: Re-read the status from each port and refresh the whole screen.

5.3. Port Configuration

Configure enable state, auto-negotiation, speed/duplex, and flow control for each port.

Item Option Default value

Enable Enable / Disabled Enable

Auto On /Off.

If the port was disabled, the item is displayed as “---“ .

If this set to Off, then Spd / Dpx should not be set to

Auto

On

Spd / Dpx Auto/ 100F/ 100H /10F /10H.

F: Full duplex, H: Half duplex.

If the port was disabled, the item is displayed as “---“ .

Auto

Flow Control On / Off

If port disabled, the item is displayed as “---“ .

On

24+2G Web Smart-switch User Manual

Revision 1.0- 15

Notice: In this example, when Port 3 and Port 4 are configured to be trunk group 1, thus Port3/Port4

will be disappeared from the list and replaced by Trunk 1 indication.

5.4. Trunk Configuration

Configure the trunk groups. There are max. 7 trunk groups can be configured. User can arbitrarily

select up to four ports from port1~port24 or port25~port26 to make a trunk group.

Notice:

1: The 10/100Mbps port cannot be trunked with gigabit port.

2: All ports in the same trunk group will be treated as a single port. If VLAN group exist, all the

members in a trunk group must be in the same VLAN group.

Items Option Default value

Each trunk group Enable/Disable, which means if current trunk group is

enabled or disabled.

Disabled

Each port A “v” mark can be selected for T1~T7, which means to

which trunk group current port is belonging.

This option is exclusive, that is to say, each port could only

be one of the trunk groups.

Not a trunk member

24+2G Web Smart-switch User Manual

Revision 1.0- 16

5.5. VLAN Configuration

A Virtual LAN (VLAN) is a logical network group that limits the broadcast domain. It allows you to

isolate network traffic so only member of the VLAN receive traffic from the same VLAN members.

Basically, creating a VLAN within a switch is logically equivalent of reconnecting a group physically.

The XP-3241 supports port-based and tag-based (802.1Q) VLAN mode. In the default configuration,

VLAN is disabled. If enabled the 802.1Q VLAN, initially, all ports on the switch belong to default

VLAN, VID is 1.

Notice: You cannot delete the default VLAN group in 802.1Q VLAN mode.

Item Description

VLAN Configuration Add / Delete VLAN groups.

Advanced 802.1Q VLAN Setting Ingress filters configuration.

Return to Main Menu Back to main menu.

24+2G Web Smart-switch User Manual

Revision 1.0- 17

5.5.1. VLAN Mode: Port-based VLAN

Packets can be forwarded only to members of the same VLAN group.

Special items in the Action Menu:

<Add>: Add a new group and enter the editing page.

<Delete>: Delete an existing group.

Item Option Default value

Group ID 1~255.(max. 24 VLAN group) 0

Each port --- / Member ---

24+2G Web Smart-switch User Manual

Revision 1.0- 18

5.5.2. Port-based VLAN Group <Add>/<Edit>Menu

Packets are delivered to only members of the same VLAN group. Note all unselected ports are treated

as belonging to another single VLAN. If the port-based VLAN enabled, the VLAN-tagging is

ignored.

Item Option Default value

Group ID 1~255.(max. 24 VLAN group) 0

Each port --- / Member ---

24+2G Web Smart-switch User Manual

Revision 1.0- 19

5.5.3. VLAN Mode: 802.IQ VLAN

Packets are delivered to the members of the same VLAN group, which is recognized by 802.IQ tag.

PVID(Port VID): Set the port VLAN ID that will be assigned to untagged traffic on a given port.

This feature is useful for accommodating devices that you want to participate in the VLAN but don’t

support tagging.

Each port of XP-3241 allows user to assign one PVID, range from 1~255, default PVID is 1. The

PVID must be as same as the VLAN ID that the port belongs to which VLAN group, or the untagged

traffic will be dropped.

Special items in the Action Menu:

<Add>: Add a new group and enter the editing page.

<Delete>: Delete an existing group.

5.5.4. 802.IQ VLAN Group <Add>/ <Edit> Menu

If the trunk groups exists, you can see it (e.g. TRUNK1, TRUNK2 …) after port24. And, you can

configure it to be a member of the VLAN group.

Notice: The limitation of VLAN ID (range from 1~255, not from 1~4094) is chip's limitation.

Items Option Default value

VLAN ID 1~255 (max. 24 VLAN group) 0

Each port ---/Tagged/Untagged.

a. ---: This port is NOT a member of this VLAN group.

b. Tagged: this port is the member of this VLAN group

and outgoing frames are VLAN-tagged frame.

c. Untagged: this port is the member of this VLAN group

and outgoing framed are NOT VLAN-tagged frames.

---

24+2G Web Smart-switch User Manual

Revision 1.0- 20

5.5.5. Advanced 802.1Q VLAN Configuration

Ingress filters configuration.

5.6. Port Monitoring Configuration

Port monitoring is forwarding specified direction of packets from several monitored ports to a

specified monitoring port.

Items Option Default value

Port Monitoring Mode Disable / RX / TX / RX & TX Disable

Port Monitoring Port PORT1~PORT24, PORT25~26.

Any single port but is not a trunk group

PORT 1

Monitoring Port --- / Monitored. ---

Page is loading ...

CTC Union FSW3224 User manual

CTC Union FSW3224 User manual

Related papers

Other documents