Vega EL 3 Operating instructions

Brand: Vega

Model: EL 3

Type: Operating instructions

Vega EL 3 is a point level sensor for conductive liquids. It is used to detect high or low levels in a variety of industrial applications, including chemical, food, and beverage industries. The EL 3 can also be used in hazardous areas, as it is certified for use in Zone 0, 1, and 2.

Operating Instructions

Conductive multiple rod electrode

Conductive probe EL 3

Document ID: 32652

Contents

Conductive probe EL 3 •

32652-EN-160727

Contents

1 About this document

1.1 Function ........................................................................................................................... 3

1.2 Target group ..................................................................................................................... 3

1.3 Symbols used................................................................................................................... 3

2 For your safety

2.1 Authorised personnel ....................................................................................................... 4

2.2 Appropriate use ................................................................................................................ 4

2.3 Warning about incorrect use ............................................................................................. 4

2.4 General safety instructions ............................................................................................... 4

2.5 Safety instructions for Ex areas ........................................................................................ 5

2.6 Environmental instructions ............................................................................................... 5

3 Product description

3.1 Conguration .................................................................................................................... 6

3.2 Principle of operation........................................................................................................ 7

3.3 Adjustment ....................................................................................................................... 7

3.4 Packaging, transport and storage ..................................................................................... 8

4 Mounting

4.1 General instructions ......................................................................................................... 9

4.2 Mounting instructions ....................................................................................................... 9

5 Connecting to power supply

5.1 Preparing the connection ............................................................................................... 12

5.2 Wiring plan ..................................................................................................................... 12

6 Setup

6.1 General information ........................................................................................................ 15

7 Maintenanceandfaultrectication

7.1 Maintenance .................................................................................................................. 16

7.2 Rectify faults ................................................................................................................... 16

7.3 Shortening the probe ...................................................................................................... 16

7.4 How to proceed if a repair is necessary .......................................................................... 16

8 Dismount

8.1 Dismounting steps.......................................................................................................... 17

8.2 Disposal ......................................................................................................................... 17

9 Supplement

9.1 Technical data ................................................................................................................ 18

9.2 Dimensions .................................................................................................................... 19

9.3 Industrial property rights ................................................................................................. 20

Editing status: 2015-05-27

1 About this document

Conductive probe EL 3 •

32652-EN-160727

1 About this document

1.1 Function

This operating instructions manual provides all the information you

need for mounting, connection and setup as well as important instruc-

tionsformaintenanceandfaultrectication.Pleasereadthisinforma-

tion before putting the instrument into operation and keep this manual

accessible in the immediate vicinity of the device.

1.2 Target group

This operating instructions manual is directed to trained specialist

personnel. The contents of this manual should be made available to

these personnel and put into practice by them.

1.3 Symbols used

Information, tip, note

This symbol indicates helpful additional information.

Caution: If this warning is ignored, faults or malfunctions can result.

Warning: If this warning is ignored, injury to persons and/or serious

damage to the instrument can result.

Danger: If this warning is ignored, serious injury to persons and/or

destruction of the instrument can result.

Ex applications

This symbol indicates special instructions for Ex applications.

SIL applications

This symbol indicates instructions for functional safety which must be

taken into account particularly for safety-relevant applications.

•

List

The dot set in front indicates a list with no implied sequence.

→

Action

This arrow indicates a single action.

1 Sequence of actions

Numbers set in front indicate successive steps in a procedure.

Battery disposal

This symbol indicates special information about the disposal of bat-

teries and accumulators.

2 For your safety

Conductive probe EL 3 •

32652-EN-160727

2 For your safety

2.1 Authorised personnel

All operations described in this operating instructions manual must

be carried out only by trained specialist personnel authorised by the

plant operator.

During work on and with the device the required personal protective

equipment must always be worn.

2.2 Appropriate use

The EL 3 is a sensor for point level detection.

Youcannddetailedinformationabouttheareaofapplicationin

chapter "Product description".

Operational reliability is ensured only if the instrument is properly

usedaccordingtothespecicationsintheoperatinginstructions

manual as well as possible supplementary instructions.

For safety and warranty reasons, any invasive work on the device

beyond that described in the operating instructions manual may be

carried out only by personnel authorised by the manufacturer. Arbi-

traryconversionsormodicationsareexplicitlyforbidden.

2.3 Warning about incorrect use

Inappropriate or incorrect use of the instrument can give rise to

application-specichazards,e.g.vesseloverllordamagetosystem

components through incorrect mounting or adjustment.

2.4 General safety instructions

This is a state-of-the-art instrument complying with all prevailing

regulations and guidelines. The instrument must only be operated in a

technicallyawlessandreliablecondition.Theoperatorisresponsible

for the trouble-free operation of the instrument.

During the entire duration of use, the user is obliged to determine the

compliance of the necessary occupational safety measures with the

current valid rules and regulations and also take note of new regula-

tions.

The safety instructions in this operating instructions manual, the na-

tional installation standards as well as the valid safety regulations and

accident prevention rules must be observed by the user.

For safety and warranty reasons, any invasive work on the device

beyond that described in the operating instructions manual may be

carried out only by personnel authorised by the manufacturer. Arbi-

traryconversionsormodicationsareexplicitlyforbidden.

The safety approval markings and safety tips on the device must also

be observed.

2 For your safety

Conductive probe EL 3 •

32652-EN-160727

2.5 Safety instructions for Ex areas

PleasenotetheEx-specicsafetyinformationforinstallationandop-

eration in Ex areas. These safety instructions are part of the operating

instructions manual and come with the Ex-approved instruments.

2.6 Environmental instructions

Protection of the environment is one of our most important duties.

That is why we have introduced an environment management system

with the goal of continuously improving company environmental pro-

tection.Theenvironmentmanagementsystemiscertiedaccording

to DIN EN ISO 14001.

Pleasehelpusfullthisobligationbyobservingtheenvironmental

instructions in this manual:

•

Chapter "Packaging, transport and storage"

•

Chapter "Disposal"

3 Product description

Conductive probe EL 3 •

32652-EN-160727

3 Product description

3.1 Conguration

The scope of delivery encompasses:

•

EL 3 point level switch

•

Documentation

– This operating instructions manual

– Ex-specic"Safety instructions" (with Ex versions)

– Ifnecessary,furthercerticates

The EL 3 consists of the components:

•

Housing lid

•

Housing

•

Processttingwithelectrode

Fig. 1: Conductive multiple rod electrode EL 3

1 Housing lid

2 Housing

3 Processtting

To create a measuring system you need one conductive probe and a

VEGATOR 131, 132, 256C, 631 or 632 signal conditioning instrument.

The type label contains the serial number of the instrument. With it

youcanndthefollowinginstrumentdataonourhomepage:

Scope of delivery

Constituent parts

Serial number - Instru-

ment search

3 Product description

Conductive probe EL 3 •

32652-EN-160727

•

Product code (HTML)

•

Delivery date (HTML)

•

Order-specicinstrumentfeatures(HTML)

•

Operating instructions and quick setup guide at the time of ship-

ment (PDF)

•

Order-specicsensordata

Go to "www.vega.com", "VEGA Tools" and "Instrument search". Enter

the serial number.

Alternatively, you can access the data via your smartphone:

•

Download the smartphone app "VEGA Tools" from the "Apple App

Store" or the "Google Play Store"

•

Scan the Data Matrix code on the type label of the instrument or

•

Enter the serial number manually in the app

3.2 Principle of operation

EL 3 is a point level sensor with partly insulated conductive electrode

for level detection.

EL 3 is very rugged and can be used in all areas of industrial process

technology.

The level switch can be used in conductive liquids such as e.g. water.

Typicalapplicationsareoverllanddryrunprotection.

The conductive measuring principle places no special requirements

oninstallation.Hence,manydierentapplicationscanbeequipped

with EL 3.

Conductive probes detect the product resistance when their elec-

trodes are covered by the product.

The switching signal is determined by the length or mounting position

of the respective electrode.

Alowalternatingcurrentowsthroughtheelectodes,ismeasuredfor

amplitude and phase position by the electronics of the signal condi-

tioning instrument and converted into a switching command.

EL 3 is operated with an external processing unit. The connected

signal conditioning instrument powers EL 3 and provides a switching

signal. A connected device can be activated directly with this switch-

ing command (e.g. a warning system, a PLC, a pump, etc.).

Youcanndtheexactrangeofthevoltagesupplyinchapter"Techni-

cal data" in the operating instructions manual of the signal condition-

ing instrument.

3.3 Adjustment

The probe does not have its own electronics. The measurement is

carried out via the connected signal conditioning instrument.

Area of application

Functional principle

Voltage supply

3 Product description

Conductive probe EL 3 •

32652-EN-160727

3.4 Packaging, transport and storage

Your instrument was protected by packaging during transport. Its

capacity to handle normal loads during transport is assured by a test

based on ISO 4180.

The packaging of standard instruments consists of environment-

friendly, recyclable cardboard. For special versions, PE foam or PE

foil is also used. Dispose of the packaging material via specialised

recycling companies.

Transport must be carried out in due consideration of the notes on the

transport packaging. Nonobservance of these instructions can cause

damage to the device.

The delivery must be checked for completeness and possible transit

damage immediately at receipt. Ascertained transit damage or con-

cealed defects must be appropriately dealt with.

Up to the time of installation, the packages must be left closed and

stored according to the orientation and storage markings on the

outside.

Unless otherwise indicated, the packages must be stored only under

the following conditions:

•

Not in the open

•

Dry and dust free

•

Not exposed to corrosive media

•

Protected against solar radiation

•

Avoiding mechanical shock and vibration

•

Storage and transport temperature see chapter "Supplement -

Technical data - Ambient conditions"

•

Relative humidity 20 … 85 %

Packaging

Transport

Transport inspection

Storage

Storage and transport

temperature

4 Mounting

Conductive probe EL 3 •

32652-EN-160727

4 Mounting

4.1 General instructions

In general the level switch can be mounted in any position. The instru-

ment must be mounted in such a way that the probe is at the height of

the requested switching point.

The probe is provided with a special hexagon for tightening. Due to

the hexagon shape, the housing itself can be used to screw the instru-

ment in.

Thewrenchsizeisstatedinchapter"Supplement" under "Dimen-

sions".

Use the recommended cables (see chapter "Connecting to power

supply") and tighten the cable gland.

You can give your EL 3 additional protection against moisture pene-

tration by leading the connection cable downward in front of the cable

entry.Rainandcondensationwatercanthusdraino.Thisapplies

mainly to outdoor mounting as well as installation in areas where high

humidity is expected (e.g. through cleaning processes) or on cooled

or heated vessels.

Fig. 2: Measures against moisture ingress

Do not hold EL 3 on its electrode rods. Particularly with long rod ver-

sions, the sensor can be damaged by the weight of the instrument.

Theprocessttingmustbesealedifthereisgaugeorlowpressurein

the vessel. Before use, check if the seal material is resistant against

the measured product and the process temperature.

Themax.permissiblepressureisspeciedinchapter"Technical

data" or on the type label of the sensor.

4.2 Mounting instructions

Due to agitators, equipment vibration or similar, the level switch can

be subjected to strong lateral forces.

Extreme vibration caused by the system, e.g. due to agitators or

turbulenceinthevesselfromuidisation,cancausetheprobeofEL

3 to vibrate in resonance. If a longer rod version is necessary, you can

secure the probe by fastening a suitable isolated brace or guy directly

above the end of the rod.

Switching point

Handling

Moisture

Transport

Pressure/Vacuum

Agitatorsanduidization

4 Mounting

Conductive probe EL 3 •

32652-EN-160727

Fig. 3: Fasten the probe

1 Measuring probe

2 Plastic sleeve at the probe end or laterally mounted

IfEL3ismountedinthellingstream,unwantedfalsemeasurement

signals can be generated. For this reason, mount EL 3 at a position in

thevesselwherenodisturbances,e.g.fromllingopenings,agitators,

etc., can occur.

This applies particularly to instrument versions with a longer probe.

Fig.4:Inowingmedium

The probe should protrude into the vessel to avoid buildup. For that

reason,avoidusinghighmountingbossesforscrew-inttings.This

applies particularly to use in adhesive products.

Inowingmedium

Mounting socket

4 Mounting

Conductive probe EL 3 •

32652-EN-160727

Make sure that the mechanical connection of the probe to the vessel

iselectricallyconductivetoensuresucientgrounding.

Use conductive seals, such as those made of copper or lead, etc.

Insulatingmeasures,suchascoveringthethreadwithTeontape,

can interrupt the necessary electrical connection with metal vessels.

For this reason, ground the probe on the vessel or use a conductive

seal material.

Ground connection

5 Connecting to power supply

Conductive probe EL 3 •

32652-EN-160727

5 Connecting to power supply

5.1 Preparing the connection

Always keep in mind the following safety instructions:

Warning:

Connect only in the complete absence of line voltage.

•

The electrical connection must only be carried out by trained

personnel authorised by the plant operator.

•

Alwaysswitchopowersupply,beforeconnectingordisconnect-

ing the instrument.

YoucanndtheelectricalconnectionofEL3intheoperatinginstruc-

tions manual of the corresponding signal conditioning instrument.

Youcanndsuitablesignalconditioninginstrumentsinchapter"Tech-

nical data".

The instrument is connected with standard two-wire cable without

screen. If electromagnetic interference is expected which is above the

test values of EN 61326 for industrial areas, screened cable should

be used.

Use cable with round cross-section. A cable outer diameter of

5…9mm(0.2…0.35in)ensuresthesealeectofthecablegland.

Ifyouareusingcablewithadierentdiameterorcross-section,

exchange the seal or use a suitable cable gland.

5.2 Wiring plan

YoucanndtheelectricalconnectionofEL3intheoperatinginstruc-

tions manual of the corresponding signal conditioning instrument.

The line break monitoring is required for probes with approval accord-

ing to WHG (WRA) or Ex.

Thelinebreakmonitoringoralarmfunctiondenesthefunctionofthe

signal conditioning instrument in case of failure.

Torealizelinebreakmonitoringwiththesignalconditioninginstru-

ments VEGATOR 131, 132, 631 and 632, a supplementary electron-

ics must be mounted in the connection housing of the probe.

The supplementary electronics for line break monitoring is available in

twodierentversionsdieringopticallyinthecablecolours.

•

Cable colour red - in conjunction with a VEGATOR 632 signal

conditioning instrument

•

Cable colour blue - in conjunction with a VEGATOR 131, 132, 631

signal conditioning instrument

Note safety instructions

Voltage supply

Connection cable

Terminal compartment

Line monitoring with VE-

GATOR 131, 132, 631, 632

5 Connecting to power supply

Conductive probe EL 3 •

32652-EN-160727

Fig. 5: Supplementary electronics for line break monitoring in conjunction with

VEGATOR 131, 132, 631, 632

1 Connection cable red - in conjunction with the VEGATOR 632 signal condi-

tioning instrument

Connection cable blue - in conjunction with the VEGATOR 131, 132, 631

signal conditionings instrument

Mounting - Supplementary electronics

To mount the supplementary electronics, proceed as follows:

1. Connect the eyelet according to the following illustration.

Make sure that the eyelets have no contact to other metal parts.

2. Open one of the other terminals and attach the additional elec-

tronics.

3. Tighten the terminal.

Fig. 6: Mounting of the additional electronics for line break monitoring

1 Connection to terminal 1 (ground rod = longest rod)

2 Connection to terminal 2 (max. rod = shortest rod)

3 Additional electronics for line break monitoring

If you are using a probe without additional electronics for line break

monitoring, a fault signal will be triggered.

5 Connecting to power supply

Conductive probe EL 3 •

32652-EN-160727

Keep in mind that in case of a fault signal also the switching output

will be activated.

Only failures of channel 1 are monitored.

Take note of the operating instructions manual of the signal condition-

ing instrument.

6 Setup

Conductive probe EL 3 •

32652-EN-160727

6 Setup

6.1 General information

YoucanndthesetupprocedureforEL3intheoperatinginstructions

manual of the corresponding signal conditioning instrument.

7Maintenanceandfaultrectication

Conductive probe EL 3 •

32652-EN-160727

7 Maintenanceandfaultrectication

7.1 Maintenance

If the instrument is used properly, no special maintenance is required

in normal operation.

7.2 Rectify faults

EL3oersmaximumreliability.Nevertheless,faultscanoccurduring

operation. These may be caused by the following, e.g.:

•

Sensor

•

Process

•

Voltage supply

•

Signal processing

Youcanndinformationonfaultrecticationintheoperatinginstruc-

tions manual of the corresponding signal conditioning instrument.

Should these measures not be successful, please call in urgent cases

the VEGA service hotline under the phone no. +49 1805 858550.

Thehotlineismanned7daysaweekround-the-clock.Sinceweoer

this service worldwide, the support is only available in the English

language. The service is free, only standard call charges are incurred.

7.3 Shortening the probe

The probe can be shortened by any amount.

Note:

Take note when shortening multiple probes that terminal 1 corre-

sponds to the longest probe and terminal 2 to the shortest probe.

7.4 How to proceed if a repair is necessary

Youcanndaninstrumentreturnformaswellasdetailedinforma-

tion about the procedure in the download area of our homepage:

www.vega.com.

By doing this you help us carry out the repair quickly and without hav-

ing to call back for needed information.

If a repair is necessary, please proceed as follows:

•

Printandlloutoneformperinstrument

•

Clean the instrument and pack it damage-proof

•

Attach the completed form and, if need be, also a safety data

sheet outside on the packaging

•

Please contact the agency serving you to get the address for

thereturnshipment.Youcanndtheagencyonourhomepage

www.vega.com.

Causes of malfunction

Faultrectication

24 hour service hotline

8 Dismount

Conductive probe EL 3 •

32652-EN-160727

8 Dismount

8.1 Dismounting steps

Warning:

Before dismounting, be aware of dangerous process conditions such

as e.g. pressure in the vessel, high temperatures, corrosive or toxic

products etc.

Take note of chapters "Mounting" and "Connecting to power supply"

and carry out the listed steps in reverse order.

8.2 Disposal

The instrument consists of materials which can be recycled by spe-

cialised recycling companies. We use recyclable materials and have

designed the parts to be easily separable.

WEEE directive 2002/96/EG

This instrument is not subject to the WEEE directive 2002/96/EG and

the respective national laws. Pass the instrument directly on to a spe-

cialised recycling company and do not use the municipal collecting

points. These may be used only for privately used products according

to the WEEE directive.

Correctdisposalavoidsnegativeeectsonhumansandtheenviron-

ment and ensures recycling of useful raw materials.

Materials: see chapter "Technical data"

If you have no way to dispose of the old instrument properly, please

9 Supplement

Conductive probe EL 3 •

32652-EN-160727

9 Supplement

9.1 Technical data

Note for approved instruments

The technical data in the respective safety instructions are valid for approved instruments (e.g. with

Exapproval).Thesedatacandierfromthedatalistedherein,forexampleregardingtheprocess

conditions or the voltage supply.

General data

Materials 316Ti corresponds to 1.4571, 316L corresponds to 1.4404 or 1.4435

Materials, wetted parts

Ʋ Processtting 316Ti

Ʋ Process seal Klingersil C-4400

Ʋ insulation (partly insulated) PTFE

Ʋ Probe (rod partly PTFE insulated:

ø 6 mm/0.236 in)

316Ti, Alloy C4 (2.4610)

Materials, non-wetted parts

Ʋ Housing 316Ti

Ʋ Housing lid PBT

Ʋ Seal between housing and housing lid NBR

Ʋ Cable gland PA

Ʋ Sealing, cable gland NBR

Ʋ Blind plug, cable gland PA

Processtting G1½ (DIN 3852-A)

Weight

Ʋ With stainless steel housing 900g(32oz)

Ʋ Rod weight: ø 6 mm (0.236 in) 220g/m(2.4oz/ft)

Sensor length (L1 - L5) 0.1 … 6 m (0.328 … 19.69 ft)

Insulation length 78 mm (3.15 in)

Output variable

Suitable signal conditioning instruments VEGATOR 131, 132, 256C, 631, 632

Ambient conditions

Ambient temperature on the housing -40 … +80 °C (-40 … +176 °F)

Storage and transport temperature -40 … +80 °C (-40 … +176 °F)

Process conditions

Process pressure -1 … 63 bar/-100 … 6300 kPa (-14.5 … 914 psig)

Process temperature EL 3 of 316L -50 … +130 °C (-58 … +266 °F)

Conductance of the medium min. 7.5 µS/cm

9 Supplement

Conductive probe EL 3 •

32652-EN-160727

Electromechanical data

Cable entry 1 x cable gland M20 x 1.5 (cable:

ø 5 … 9 mm/0.2 … 0.35 in)

Electrical protective measures

Protection rating IP 66/IP 67 (NEMA Type 4X)

Approvals

Instrumentswithapprovalscanhavedierenttechnicalspecicationsdependingontheversion.

For that reason the associated approval documents of these instruments have to be carefully

noted. They are part of the delivery or can be downloaded under www.vega.com, "VEGA Tools"

and "Instrument search" as well as in the general download area.

9.2 Dimensions

M20x1,5

66mm

(2.59")

57mm

(2.24")

ø6 mm

(0.24")

59mm

(2.32")

80mm

(3.15")

20mm

(0.79")

SW 60mm

(2.36")

G1½A

Fig. 7: Conductive multiple rod electrode EL 3

L1 Longest rod - Sensor length, see chapter "Technical data"

L2 Shortest rod - Sensor length, see chapter "Technical data"

L3 Sensor length, see chapter "Technical data"

9 Supplement

Conductive probe EL 3 •

32652-EN-160727

9.3 Industrial property rights

VEGA product lines are global protected by industrial property rights. Further information see

www.vega.com.

Only in U.S.A.: Further information see patent label at the sensor housing.

VEGA Produktfamilien sind weltweit geschützt durch gewerbliche Schutzrechte.

Nähere Informationen unter www.vega.com.

Les lignes de produits VEGA sont globalement protégées par des droits de propriété intellec-

tuelle. Pour plus d'informations, on pourra se référer au site www.vega.com.

VEGA lineas de productos están protegidas por los derechos en el campo de la propiedad indus-

trial. Para mayor información revise la pagina web www.vega.com.

Линии продукции фирмы ВЕГА защищаются по всему миру правами на интеллектуальную

собственность. Дальнейшую информацию смотрите на сайте www.vega.com.

VEGA系列产品在全球享有知识产权保护。

进一步信息请参见网站<www.vega.com。

9.4 Trademark

All the brands as well as trade and company names used are property of their lawful proprietor/

originator.

Page is loading ...

Vega EL 3 Operating instructions

Brand: Vega

Model: EL 3

Type: Operating instructions

Download PDF

report

Vega EL 3 Operating instructions

Vega EL 3 Operating instructions

Related papers

Other documents