Tripp Lite HDMI Over Cat5 1x2 Extenders Owner's manual

HDMI Over Cat5 1x2 Extenders
Tripp Lite
Brand
Tripp Lite
Model
HDMI Over Cat5 1x2 Extenders
Category
AV extenders
Type
Owner's manual

This manual is also suitable for

Owner’s Manual
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Copyright © 2013 Tripp Lite. All rights reserved.
HDMI Over Cat5
1x2 Extenders
Models: B126-2A1, B126-2A0
Warranty
Registration:
register online today for a
chance to win a FREE Tripp Lite
product—www.tripplite.com/warranty
Package Contents 2
Product Features 2
Mounting Instructions 4
Standard 1 x 2 Extender Kit Installation 5
1 x 2 Extender Kit with Remote/Repeater Installation 7
Standard Extender/Splitter Installation 10
Extender/Splitter with Remote/Repeater Installation 13
Troubleshooting 17
Warranty & Warranty Registration 19
13-08-043 93-32D0.indd 1 8/28/2013 2:17:35 PM
2
Package Contents
Product Features
• ExtendsanHDMIsignalto2monitorsupto200ft.fromthesource
over a single Cat5e/6 cable.
• AB126-002orB126-004extender/splittertransmitterunitisrequired
forusewiththeB126-1A01x2receiverunit.
• Extendsa1080p (60Hz)signalup to150ft. fromthesource using
Cat6 cabling, or up to 125 ft. using Cat5 cabling.
• Extends a 1080i (60Hz)signal up to 200 ft. from the source using
Cat6 cabling, or up to 175 ft. using Cat5 cabling.
• Use24AWG,solidwireCat5e/6cable,suchasTrippLite’sN202-Series,
toachievemaximumdistanceandresolution.
• FurtherexpandtherangeandnumberofmonitorsbyaddingB126-110
repeater units.
• AdduptothreerepeatersoneachCat5e/6channel,foratotalof4
displays per channel (An Active remote receiver should be the last unit
in a channel).
• A1080p(60Hz)signalcanbeextendedupto125ft.foreachrepeater
addedintoachannel(orupto175ft,fora1080i(60Hz)signalwhen
usingeitherCat5eorCat6cabling).
• Supports24-bitTrueColor(8-bitsperchannel).
• Built-inequalizationcontroltoadjustthevideoimage.
• B126-2A1KitorB126-2A0ReceiverUnit
• ExternalPowerSupply
(Input:100-240V,50/60Hz,0.5AOutput:5V,2A)
• MountingHardware
• ScrewdriverforEqualizationAdjustment
• Owner’sManual
13-08-043 93-32D0.indd 2 8/28/2013 2:17:35 PM
3
Product Features
• Supports both stereo and 7.1-channel surround sound audio
(7.1-channel surround sound signal will be Multi-Channel or PCM).
• HDCPand3Dcompatible.
• Plugandplay;Nosoftwareordriversrequired.
• Compatiblewithalloperatingsystems.
• Mountinghardwareincluded.
Optional Accessories:
• B126-110–RemoteRepeaterUnit
• N202-SeriesCat624AWG,SolidWirePatchCables
• P568-SeriesHigh-SpeedHDMICables
13-08-043 93-32D0.indd 3 8/28/2013 2:17:35 PM
4
Mounting Instructions
The B126-2A1 and B126-2A0 come with mounting hardware
that allows them to be mounted in a variety of ways. The following
images show the different ways the included mounting brackets
can be attached for different mounting methods. Note: The images
below show a B126-1A1 HDMI over Cat5 Receiver Unit, but the
mounting hardware installation is the same for the B126-2A1
and B126-2A0.
Wall-mount 1 Wall-mount 2
19” Rackmount Pole Mount
13-08-043 93-32D0.indd 4 8/28/2013 2:17:37 PM
OPTIONAL LOCAL
MONITOR
LOCAL
TRANSMITTER
REMOTE
RECEIVER
BLU-RAY
MONITOR 1
Up to 200 ft. at 1080i @ 60Hz (Cat6)
Up to 150 ft. at 1080p @ 60Hz (Cat6)
MONITOR 2
5
Standard 1 x 2 Extender Kit Installation
Notes:
1. Test to make sure that the entire installation works properly before
running cables through ceilings/walls.
2. 24 AWG, solid wire Cat5e/6 cable, such as Tripp Lite’s N202-Series, is
required to achieve maximum distance and resolution.
3. The diagram below shows the maximum extension distance when
using Cat6 cabling. When using Cat5 cabling, the maximum extension
distance is 175 ft. at 1080i (60Hz), and 125 ft. at 1080p (60Hz).
4. The B126-2A1 is set to transmit a stereo audio signal by default.
Press the Audio button on the transmitter unit to switch to 7.1-channel
surround sound audio. (7.1-channel surround sound signal will be
Multi-Channel or PCM)
13-08-043 93-32D0.indd 5 8/28/2013 2:17:38 PM
6
Standard 1 x 2 Extender Kit Installation
1
MakesurealldevicesbeingconnectedarepoweredOFF.
2
ConnecttheHDMIsourcetotheINPUT port on the transmitter unit
usingaTrippLiteP568-SeriesHigh-SpeedHDMICable.
3
Optional: Connect a monitor to the LOCAL port on the transmitter
unitusingaTrippLiteP568-SeriesHigh-SpeedHDMICable.
4
Connecttheexternalpowersupplytothetransmitterunitandplugthe
transmitterunitintoaTrippLiteSurgeSuppressor,PowerDistribution
Unit(PDU),orUninterruptiblePowerSupply(UPS).ThegreenRJ45LED
illuminatestoindicatethattheunitisreceivingpowerfromtheexternal
power supply.
5
UsingCat5e/6cable,connecttheRJ45portonthetransmitterunit
marked OUTPUTtotheRJ45portonthereceiverunitmarkedINPUT.
6
Connect theexternal power supply tothe receiver unit andplug the
receiverunitintoaTrippLiteSurgeSuppressor,PowerDistributionUnit
(PDU), or Uninterruptible Power Supply (UPS). The green RJ45 LED
illuminatestoindicatethattheunitisreceivingpowerfromtheexternal
power supply.
7
Connect a monitor to the OUTPUT 1 port on the receiver unit using a
TrippLiteP568-SeriesHigh-SpeedHDMIcable.
8
Repeat step 7 for the OUTPUT 2 port on the receiver unit.
9
Turnonthepowertotheconnecteddevices.TheorangeRJ45LED’s
on the transmitter and receiver units illuminate to indicate that a
signalisbeingreceivedfromtheHDMIsource.Thevideoimagewill
now be displayed on the connected monitors.
10
Ifnecessary,usetheEqualizationcontrolonthereceiverunittoadjust
the video image. Note: An improper Equalization setting can cause
the monitor not to display an image at all. Try each setting until an
acceptable image is displayed.
13-08-043 93-32D0.indd 6 8/28/2013 2:17:38 PM
OPTIONAL LOCAL
MONITOR
B126-2A1 LOCAL
TRANSMITTER
B126-2A1 REMOTE
RECEIVER
B126-110 REMOTE
REPEATER
B126-110 REMOTE
REPEATER
B126-110 REMOTE
REPEATER
Up to 175 ft. at 1080i (60Hz)
Up to 125 ft. at 1080p (60Hz)
Up to 175 ft. at 1080i (60Hz)
Up to 125 ft. at 1080p (60Hz)
BLU-RAY
Up to 175 ft. at 1080i (60Hz)
Up to 125 ft. at 1080p (60Hz)
Up to 175 ft. at 1080i (60Hz)
Up to 125 ft. at 1080p (60Hz)
MONITOR 1 MONITOR 2
7
1 x 2 Extender Kit with
Remote/Repeater Installation
Notes:
1. Test to make sure that the entire installation works properly before
running cables through ceilings/walls.
2. The diagram below shows the maximum extension distance when using
either Cat5e or Cat6 cabling. 24 AWG, solid wire Cat5e/6 cable, such
as Tripp Lite’s N202-Series, is required to achieve maximum distance
and resolution.
3. The B126-2A1 is set to transmit a stereo audio signal by default.
Press the Audio button on the transmitter unit to switch to 7.1-channel
surround sound audio. (7.1-channel surround sound signal will be
Multi-Channel or PCM)
1
MakesurealldevicesbeingconnectedarepoweredOFF.
2
ConnecttheHDMIsourcetotheINPUT port on the transmitter unit
usingaTrippLiteP568-SeriesHigh-SpeedHDMICable.
3
Optional: Connect a monitor to the LOCAL port on the transmitter
unitusingaTrippLiteP568-SeriesHigh-SpeedHDMICable.
13-08-043 93-32D0.indd 7 8/28/2013 2:17:39 PM
8
4
Connecttheexternalpowersupplytothetransmitterunitandplugthe
transmitterunitintoaTrippLiteSurgeSuppressor,PowerDistribution
Unit(PDU),orUninterruptiblePowerSupply(UPS).ThegreenRJ45LED
illuminatestoindicatethattheunitisreceivingpowerfromtheexternal
power supply.
5
UsingCat5e/6cable,connecttheRJ45portonthetransmitterunit
marked OUTPUT to the RJ45 port on the B126-110 repeater unit
marked INPUT.
6
Connect a monitor to theHDMI OUTPUT port on the repeater unit
usingaTrippLiteP568-SeriesHigh-SpeedHDMICable.
7
Connecttheexternalpowersupplytotherepeaterunitandplugthe
repeaterunit intoa TrippLite SurgeSuppressor,PowerDistribution
Unit(PDU),orUninterruptiblePowerSupply(UPS).Thegreenpower
andthegreenRJ45LEDswillilluminatetoindicatethattheunitis
receivingpowerfromtheexternalpowersupply.
Upto4unitscanbedaisy-chained(3repeatersand1activereceiver).To
addadditionalrepeaterunits,proceedtostep8.Tonishyourinstallation
withtheB126-2A1receiverunit,proceedtostep11.
8
UsingCat5e/6cable,connecttheRJ45portontherepeaterunitmarked
OUTPUTtotheRJ45portonasecondrepeaterunitmarkedINPUT.
9
Connect a monitor to theHDMI OUTPUT port on the repeater unit
usingaTrippLiteP568-SeriesHigh-SpeedHDMICable.
10
Connecttheexternalpowersupplytotherepeaterunitandplugthe
repeaterunit intoa TrippLite SurgeSuppressor,PowerDistribution
Unit(PDU),orUninterruptiblePowerSupply(UPS).Thegreenpower
andthegreenRJ45LEDswillilluminatetoindicatethattheunitis
receivingpowerfromtheexternalpowersupply.
1 x 2 Extender Kit with
Remote/Repeater Installation
13-08-043 93-32D0.indd 8 8/28/2013 2:17:39 PM
9
Toaddathirdremote/repeaterunit,repeatsteps8through10.Tonish
yourinstallationwiththeB126-2A1receiverunit,proceedtostep11.
11
Using Cat5e/6 cable, connect the RJ45 port on the repeater unit
marked OUTPUTtotheRJ45portonthereceiverunitmarkedINPUT.
12
Connect a monitor to the OUTPUT 1 port on the receiver unit using a
TrippLiteP568-SeriesHigh-SpeedHDMIcable.
13
Repeat step 12 for the OUTPUT 2 port on the receiver unit.
14
Connecttheexternalpowersupplytothereceiverunitandplugthe
receiver unit into a Tripp Lite Surge Suppressor, Power Distribution
Unit(PDU),orUninterruptiblePowerSupply(UPS).ThegreenRJ45
LEDilluminatestoindicatethatitisreceivingpowerfromtheexternal
power supply.
15
Turnonthepowertotheconnecteddevices.TheorangeRJ45LEDs
on all units will illuminate to indicate that a signal is being received
fromtheHDMIsource.Thevideoimagewillnowbedisplayedonthe
connected monitors.
16
Ifnecessary,usetheEqualization control on the repeater and receiver
units to adjust the video image. Note: An improper Equalization
setting can cause the monitor not to display an image at all. Try each
setting until an acceptable image is displayed.
1 x 2 Extender Kit with
Remote/Repeater Installation
13-08-043 93-32D0.indd 9 8/28/2013 2:17:40 PM
10
Standard Extender/Splitter Installation
Notes:
1. Test to make sure that the entire installation works properly before
running cables through ceilings/walls.
2. 24 AWG, Solid Wire Cat5e/6 cable, such as Tripp Lite’s N202-Series,
is required to achieve maximum distance and resolution.
3. The diagram below shows the maximum extension distance when
using Cat6 cabling. When using Cat5 cabling, the maximum extension
distance is 175 ft. at 1080i (60Hz), and 125 ft. at 1080p (60Hz).
4. The B126-002 and B126-004 are set to transmit a stereo audio
signal by default. Press the Audio button on the transmitter unit to
switch to 7.1-channel surround sound audio. (7.1-channel surround
sound signal will be Multi-Channel or PCM)
5. The diagram below shows the B126-004 transmitter unit. Installation
is the same for the B126-002, except that there are only two output
ports and no local monitor port.
6. Although the installation instructions below mention the B126-2A0 1x2
receiver unit only, Tripp Lite offers several standard receiver units that
can be used in the event that only one monitor is required on the remote
end: B126-1A0, B126-1A0-WP-1, B126-1P0, and B126-1P0-WP-1.
13-08-043 93-32D0.indd 10 8/28/2013 2:17:40 PM
B126-004
OPTIONAL LOCAL
MONITOR
BLU-RAY
B126-2A0B126-2A0
B126-2A0B126-2A0
Up to 200 ft. at 1080i @ 60Hz (Cat6)
Up to 150 ft. at 1080p @ 60Hz (Cat6)
HDMI OVER Cat5
1 x 2 EXTENDER
REMOTE UNIT
MODEL: B126-2A0
HDMI OVER Cat5
1 x 2 EXTENDER
REMOTE UNIT
MODEL: B126-2A0
HDMI OVER Cat5
1 x 2 EXTENDER
REMOTE UNIT
MODEL: B126-2A0
HDMI OVER Cat5
1 x 2 EXTENDER
REMOTE UNIT
MODEL: B126-2A0
11
Standard Extender/Splitter Installation
1
MakesurealldevicesbeingconnectedarepoweredOFF.
2
Connect the HDMI source to the INPUT port on a B126-002 or
B126-004transmitterunitusingaTrippLiteP568-SeriesHigh-Speed
HDMICable.
3
Optional for B126-004: Connect a monitor to the LOCAL port on the
transmitterunitusingaTrippLiteP568-SeriesHigh-SpeedHDMICable.
4
Connecttheexternalpowersupplytothetransmitterunitandplugthe
transmitterunitintoaTrippLiteSurgeSuppressor,PowerDistribution
Unit(PDU),orUninterruptiblePowerSupply(UPS).ThegreenRJ45
LEDsontheB126-002andB126-004,andtheredpowerLEDon
the B126-004 will illuminate to indicate that the unit is receiving
powerfromtheexternalpowersupply.
5
UsingCat5e/6cable,connectaRJ45OUTPUT port on the transmitter
unittotheRJ45INPUTportontheB126-2A01x2receiverunit.
6
Repeatstep5toaddreceiverunitstotheremainingRJ45OUTPUT
ports on the transmitter unit.
13-08-043 93-32D0.indd 11 8/28/2013 2:17:40 PM
12
7
Connect theexternal power supply tothe receiver unit andplug the
receiverunitintoaTrippLiteSurgeSuppressor,PowerDistributionUnit
(PDU), or Uninterruptible Power Supply (UPS). The green RJ45 LED
illuminatestoindicatethattheunitisreceivingpowerfromtheexternal
power supply.
8
Connect a monitor to the OUTPUT 1 port on the receiver unit using a
TrippLiteP568-SeriesHigh-SpeedHDMICable.
9
Repeatstep8fortheOUTPUT 2 port on the receiver unit.
10
Turnonthepowertotheconnecteddevices.TheorangeRJ45LEDs
on the transmitter and receiver units will illuminate to indicate that
a signalis being received from the HDMI source.The video image
should now be displayed on the connected monitors.
11
Ifnecessary,usetheEqualizationcontrolonthereceiverunittoadjust
the video image. Note: An improper Equalization setting can cause
the monitor not to display an image at all. Try each setting until an
acceptable image is displayed.
Standard Extender/Splitter Installation
13-08-043 93-32D0.indd 12 8/28/2013 2:17:40 PM
13
Extender/Splitter with
Remote/Repeater Installation
Notes:
1. Test to make sure that the entire installation works properly before
running cables through ceilings/walls.
2. The diagram below shows the maximum extension distance when using
either Cat5e or Cat6 cabling. 24 AWG, solid wire Cat5e/6 cable, such
as Tripp Lite’s N202-Series, is required to achieve maximum distance
and resolution.
3. The B126-002 and B126-004 are set to transmit a stereo audio
signal by default. Press the Audio button on the transmitter unit to
switch to 7.1-channel surround sound audio. (7.1-channel surround
sound signal will be Multi-Channel or PCM)
4. The diagram below shows the B126-004 transmitter unit. Installation
is the same for the B126-002, except that there are only two output
ports and no local monitor port.
5. Although the installation instructions below mention the B126-2A0
1x2 receiver unit only, Tripp Lite offers two additional active receivers
that can be used in the event that only one monitor is needed at the
end of a repeater chain: B126-1A0 and B126-1A0-WP-1.
13-08-043 93-32D0.indd 13 8/28/2013 2:17:40 PM
OPTIONAL LOCAL
MONITOR
B126-004 LOCAL
TRANSMITTER
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
Up to 175 ft. at 1080i (60Hz)
Up to 125 ft. at 1080p (60Hz)
Up to 175 ft. at 1080i (60Hz)
Up to 125 ft. at 1080p (60Hz)
BLU-RAY
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-2A0
REMOTE RECEIVER
B126-2A0
REMOTE RECEIVER
B126-2A0
REMOTE RECEIVER
B126-2A0
REMOTE RECEIVER
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
HDMI OVER Cat5
1 x 2 EXTENDER
REMOTE UNIT
MODEL: B126-2A0
HDMI OVER Cat5
1 x 2 EXTENDER
REMOTE UNIT
MODEL: B126-2A0
HDMI OVER Cat5
1 x 2 EXTENDER
REMOTE UNIT
MODEL: B126-2A0
HDMI OVER Cat5
1 x 2 EXTENDER
REMOTE UNIT
MODEL: B126-2A0
14
1
MakesurealldevicesbeingconnectedarepoweredOFF.
2
Connect the HDMI source to the INPUT port on a B126-002 or
B126-004transmitterunitusingaTrippLiteP568-SeriesHigh-Speed
HDMICable.
3
Optional for B126-004: Connect a monitor to the LOCAL port on
thetransmitterunitusingaTrippLiteP568-SeriesHigh-SpeedHDMI
Cable.
4
Connecttheexternalpowersupplytothetransmitterunitandplugthe
transmitterunitintoaTrippLiteSurgeSuppressor,PowerDistribution
Unit(PDU),orUninterruptiblePowerSupply(UPS).ThegreenRJ45
LEDs on the B126-002 and B126-004, and the red LED on the
B126-004willilluminatetoindicatethattheunitisreceivingpower
fromtheexternalpowersupply.
Extender/Splitter with
Remote/Repeater Installation
13-08-043 93-32D0.indd 14 8/28/2013 2:17:41 PM
15
5
UsingCat5e/6cable,connectaRJ45OUTPUT port on the transmitter
unittotheRJ45INPUTportontheB126-110repeaterunit.
6
Connect a monitor to theHDMI OUTPUT port on the repeater unit
usingaTrippLiteP568-SeriesHigh-SpeedHDMICable.
7
Connecttheexternalpower supplytotheremote/repeater unitand
plug the remote/repeater unit into a Tripp Lite Surge Suppressor,
PowerDistributionUnit(PDU),orUninterruptiblePowerSupply(UPS).
ThegreenpowerandRJ45LEDswillilluminatetoindicatethatthe
unitisreceivingpowerfromtheexternalpowersupply.
Upto4unitscanbedaisy-chained(3repeatersand1activereceiver).To
addadditionalrepeaterunits,proceedtostep8.Tonishyourinstallation
withaB126-2A01x2receiverunit,proceedtostep11.
8
UsingCat5e/6cable,connecttheRJ45portontherepeaterunitmarked
OUTPUTtotheRJ45portonasecondrepeaterunitmarkedINPUT.
9
Connect a monitor to theHDMI OUTPUT port on the repeater unit
usingaTrippLiteP568-SeriesHigh-SpeedHDMICable.
10
Connecttheexternalpower supplytotheremote/repeater unitand
plug the remote/repeater unit into a Tripp Lite Surge Suppressor,
PowerDistributionUnit(PDU),orUninterruptiblePowerSupply(UPS).
ThegreenpowerandgreenRJ45LEDswillilluminatetoindicatethat
theunitisreceivingpowerfromtheexternalpowersupply.
Toaddathirdremote/repeaterunit,repeatsteps8through10.Tonish
yourinstallationwithaB126-2A01x2receiverunit,proceedtostep11.
Extender/Splitter with
Remote/Repeater Installation
13-08-043 93-32D0.indd 15 8/28/2013 2:17:41 PM
16
11
Using Cat5e/6 cable, connect the RJ45 port on the repeater unit
marked OUTPUT to the RJ45 port on the B126-2A0 receiver unit
marked INPUT.
12
Connect a monitor to the OUTPUT 1 port on the receiver unit using a
TrippLiteP568-SeriesHigh-SpeedHDMICable.
13
Repeat step 12 for the OUTPUT 2 port on the receiver unit.
14
Connecttheexternalpowersupplytothereceiverunitandplugthe
receiver unit into a Tripp Lite Surge Suppressor, Power Distribution
Unit(PDU),orUninterruptiblePowerSupply(UPS).ThegreenRJ45
LEDilluminatestoindicatethatitisreceivingpowerfromtheexternal
power supply.
15
Repeatsteps5through14foreachadditionalRJ45OUTPUT port on
the transmitter unit.
16
Turnonthepowertotheconnecteddevices.TheorangeRJ45LEDs
on all units will illuminate to indicate that a signal is being received
fromtheHDMIsource.Thevideoimageshouldnowbedisplayedon
the connected monitors.
17
Ifnecessary,usetheEqualization control on the repeater and receiver
units to adjust the video image. Note: An improper Equalization
setting can cause the monitor not to display an image at all. Try each
setting until an acceptable image is displayed.
Extender/Splitter with
Remote/Repeater Installation
13-08-043 93-32D0.indd 16 8/28/2013 2:17:41 PM
17
Troubleshooting
Ifyouareunabletogetanacceptableimageafterfollowingtheinstallation
instructions,trythesetroubleshootingtips:
1
Are the external power supplies that came with the product
connected and plugged into a working power source? For the
product to function properly, it must be connected to and receiving
powerfromtheexternalpowersupply.
2
Was the power to the connected devices turned off prior to
installation?Ifnot,restartthem.
3
Have you adjusted the Equalization setting on the repeater and/
or receiver units?Therearebuilt-inEqualizationadjustmentknobson
everyrepeaterandactivereceiverthatcanbeadjustedtoobtainthe
bestpicturequality.Usetheminiscrewdriverincludedwiththeproduct
toadjustthissettinguntilanacceptableimageisdisplayed.Note: An
improper Equalization setting can cause the monitor not to display an
image at all. Try each setting until an acceptable image is displayed.
4
What resolution are you trying to reach?Tripp Lite’sHDMIover
Cat5 extenders are tested to support up to 1080p (60Hz) video
resolution (See the Product Features section or the installation
diagrams in this manual for details on the maximum distance and
resolutionwhenusingtherepeaterandthedifferentreceivers).The
shortertheextensiondistance,thehighertheresolutionyouwillbe
abletoobtain.Ifyouarenotabletogetanacceptableimageafter
adjustingtheEqualizationsetting,tryloweringyourcomputer’svideo
resolutionoradjustingtherefreshrate.
13-08-043 93-32D0.indd 17 8/28/2013 2:17:41 PM
18
5
What type of cabling are you using?Inferiorcablingcanresultinpoor
performance, so it is important that you use cables that support the video
resolution you are trying to obtain. To achieve maximum distance and
resolution,24AWGsolidwireUTPcablemustbeused.TrippLite’sN202-
SeriesCat6Cablesaremadewith24AWGsolidwire,asaretheN022-
01K-GY(Cat5)andN222-01K-GYBulkCables.Also,theHDMIcablesyou
areusingmustsupporttheresolutionyouaretryingtoobtain.Inexpensive,
lowquality HDMIcables maynot supportthe maximumresolution. Itis
recommended that you use Tripp Lite’sP568-Series High-SpeedHDMI
Cablesthatarepre-testedtoworkwithallB126-Seriesextenderproducts.
6
Test your cables to ensure they are working properly. Try
connecting your HDMI cables between a source and monitor that
you know works to see if the cable is functioning. For Cat5e/6
cabling, connect it between a computer and a network to verify that it
establishes a network connection.
7
Do you have any patch panels or other devices in between
the transmitter, repeater, and receiver units? TrippLite’s HDMI
overCat5 extenderproductsare designedtobe connecteddirectly
from thetransmitter to therepeater and/or receiver viaUTP cable.
The more connection points that are in between the source and the
remote monitor, the more likely signal degradation will occur, causing
poorperformance.Ifyouhaveapatchpanelorifanotherdeviceis
being used, it should be removed from the installation.
8
Check your cabling for any damages that may have occurred
during installation.Ifacableconnectorisloosenedasaresultofbeing
pulledthroughceilings/walls,orthecablejacketisdamaged,causingthe
wiringtobeexposed,youwillnotachievemaximumperformance.
9
Are the transmitter, repeater, and/or receiver located in an area
that exposes them to higher temperatures? If the product is
overheated, it will not function properly.
Troubleshooting
13-08-043 93-32D0.indd 18 8/28/2013 2:17:41 PM
19
Warranty & Warranty Registration
1-Year Limited Warranty
TRIPP LITE warrants its products to be free from defects in materials and workmanship for a
periodofone(1)yearfromthedateofinitialpurchase.TRIPPLITE’sobligationunderthiswarranty
is limited to repairing or replacing (at its sole option) any such defective products. To obtain
service under this warranty, youmust obtain a Returned Material Authorization(RMA) number
fromTRIPPLITEoranauthorizedTRIPPLITEservicecenter.ProductsmustbereturnedtoTRIPP
LITE or an authorized TRIPP LITE service center with transportation charges prepaid and must
be accompanied by a brief description of the problem encountered and proof of date and place
ofpurchase.Thiswarrantydoesnotapplytoequipmentwhichhasbeendamagedbyaccident,
negligenceormisapplicationorhasbeenalteredormodiedinanyway.
EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Somestatesdonotpermitlimitationorexclusionofimpliedwarranties;therefore,theaforesaid
limitation(s)orexclusion(s)maynotapplytothepurchaser.
EXCEPTASPROVIDEDABOVE,INNOEVENTWILLTRIPPLITEBELIABLEFORDIRECT,INDIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS
PRODUCT, EVEN IF ADVISED OF THE POSSIBILITYOF SUCH DAMAGE. Specically, TRIPP LITE
is not liable for any costs, such as lost prots or revenue, loss of equipment, loss of use of
equipment,lossofsoftware,lossofdata,costsofsubstitutes,claimsbythirdparties,orotherwise.
WARRANTY REGISTRATION
Visit www.tripplite.com/warrantytoday to register the warranty for your new Tripp Lite product.
You’llbeautomaticallyenteredintoadrawingforachancetowinaFREETrippLiteproduct!*
*Nopurchasenecessary.Voidwhereprohibited.Somerestrictionsapply.Seewebsitefordetails.
WEEE Compliance Information for Tripp Lite Customers and Recyclers
(European Union)
Under the Waste Electrical and Electronic Equipment (WEEE) Directive and
implementing regulations, when customers buy new electrical and electronic
equipmentfromTrippLitetheyareentitledto:
• Sendoldequipmentforrecyclingonaone-for-one,like-for-likebasis(thisvaries
dependingonthecountry)
• Sendthenewequipmentbackforrecyclingwhenthisultimatelybecomeswaste
13-08-043 93-32D0.indd 19 8/28/2013 2:17:42 PM
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
13-08-043•9332D0_RevA
FCC Notice, Class B
This device complies with part 15 of the FCC Rules. Operationis subject to the following two
conditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustaccept
any interference received, including interference that may cause undesired operation.
Note:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
usesandcanradiateradiofrequencyenergyand,ifnot installedand usedin accordancewith
theinstructions,maycauseharmfulinterferencetoradiocommunications.However,thereisno
guaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescause
harmful interference to radio or television reception, which can be determined by turning the
equipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreof
thefollowingmeasures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandreceiver.
• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiveris
connected.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
AnychangesormodicationstothisequipmentnotexpresslyapprovedbyTrippLitecouldvoidthe
user’sauthoritytooperatethisequipment.
WARNING
Useofthisequipmentinlifesupportapplicationswherefailureofthisequipmentcanreasonably
beexpectedtocausethefailureofthelifesupportequipmentortosignicantlyaffectitssafety
oreffectivenessisnotrecommended.Donotusethisequipmentinthepresenceofaammable
anestheticmixturewithair,oxygenornitrousoxide.
TrippLitefollowsapolicyofcontinuousimprovement.Productspecicationsaresubjecttochange
without notice.
13-08-043 93-32D0.indd 20 8/28/2013 2:17:42 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Tripp Lite HDMI Over Cat5 1x2 Extenders Owner's manual

HDMI Over Cat5 1x2 Extenders
Tripp Lite
Brand
Tripp Lite
Model
HDMI Over Cat5 1x2 Extenders
Category
AV extenders
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents