Tripp Lite B126-2A0 Owner's manual

Owner’s Manual

1111 W. 35th Street, Chicago, IL 60609 USA

www.tripplite.com/support

HDMI Over Cat5

1x2 Extenders

Models: B126-2A1, B126-2A0

Warranty

Registration:

chance to win a FREE Tripp Lite

product—www.tripplite.com/warranty

Package Contents 2

Product Features 2

Mounting Instructions 4

Standard 1 x 2 Extender Kit Installation 5

1 x 2 Extender Kit with Remote/Repeater Installation 7

Standard Extender/Splitter Installation 10

Extender/Splitter with Remote/Repeater Installation 13

Troubleshooting 17

Warranty & Warranty Registration 19

13-08-043 93-32D0.indd 1 8/28/2013 2:17:35 PM

Package Contents

Product Features

• ExtendsanHDMIsignalto2monitorsupto200ft.fromthesource

over a single Cat5e/6 cable.

• AB126-002orB126-004extender/splittertransmitterunitisrequired

forusewiththeB126-1A01x2receiverunit.

• Extendsa1080p (60Hz)signalup to150ft. fromthesource using

Cat6 cabling, or up to 125 ft. using Cat5 cabling.

• Extends a 1080i (60Hz)signal up to 200 ft. from the source using

Cat6 cabling, or up to 175 ft. using Cat5 cabling.

• Use24AWG,solidwireCat5e/6cable,suchasTrippLite’sN202-Series,

toachievemaximumdistanceandresolution.

• FurtherexpandtherangeandnumberofmonitorsbyaddingB126-110

repeater units.

• AdduptothreerepeatersoneachCat5e/6channel,foratotalof4

displays per channel (An Active remote receiver should be the last unit

in a channel).

• A1080p(60Hz)signalcanbeextendedupto125ft.foreachrepeater

addedintoachannel(orupto175ft,fora1080i(60Hz)signalwhen

usingeitherCat5eorCat6cabling).

• Supports24-bitTrueColor(8-bitsperchannel).

• Built-inequalizationcontroltoadjustthevideoimage.

• B126-2A1KitorB126-2A0ReceiverUnit

• ExternalPowerSupply

(Input:100-240V,50/60Hz,0.5AOutput:5V,2A)

• MountingHardware

• ScrewdriverforEqualizationAdjustment

• Owner’sManual

13-08-043 93-32D0.indd 2 8/28/2013 2:17:35 PM

Product Features

• Supports both stereo and 7.1-channel surround sound audio

(7.1-channel surround sound signal will be Multi-Channel or PCM).

• HDCPand3Dcompatible.

• Plugandplay;Nosoftwareordriversrequired.

• Compatiblewithalloperatingsystems.

• Mountinghardwareincluded.

Optional Accessories:

• B126-110–RemoteRepeaterUnit

• N202-SeriesCat624AWG,SolidWirePatchCables

• P568-SeriesHigh-SpeedHDMICables

13-08-043 93-32D0.indd 3 8/28/2013 2:17:35 PM

Mounting Instructions

The B126-2A1 and B126-2A0 come with mounting hardware

that allows them to be mounted in a variety of ways. The following

images show the different ways the included mounting brackets

can be attached for different mounting methods. Note: The images

below show a B126-1A1 HDMI over Cat5 Receiver Unit, but the

mounting hardware installation is the same for the B126-2A1

and B126-2A0.

Wall-mount 1 Wall-mount 2

19” Rackmount Pole Mount

13-08-043 93-32D0.indd 4 8/28/2013 2:17:37 PM

OPTIONAL LOCAL

MONITOR

LOCAL

TRANSMITTER

REMOTE

RECEIVER

BLU-RAY

MONITOR 1

Up to 200 ft. at 1080i @ 60Hz (Cat6)

Up to 150 ft. at 1080p @ 60Hz (Cat6)

MONITOR 2

Standard 1 x 2 Extender Kit Installation

Notes:

1. Test to make sure that the entire installation works properly before

running cables through ceilings/walls.

2. 24 AWG, solid wire Cat5e/6 cable, such as Tripp Lite’s N202-Series, is

required to achieve maximum distance and resolution.

3. The diagram below shows the maximum extension distance when

using Cat6 cabling. When using Cat5 cabling, the maximum extension

distance is 175 ft. at 1080i (60Hz), and 125 ft. at 1080p (60Hz).

4. The B126-2A1 is set to transmit a stereo audio signal by default.

Press the Audio button on the transmitter unit to switch to 7.1-channel

surround sound audio. (7.1-channel surround sound signal will be

Multi-Channel or PCM)

13-08-043 93-32D0.indd 5 8/28/2013 2:17:38 PM

Standard 1 x 2 Extender Kit Installation

MakesurealldevicesbeingconnectedarepoweredOFF.

ConnecttheHDMIsourcetotheINPUT port on the transmitter unit

usingaTrippLiteP568-SeriesHigh-SpeedHDMICable.

Optional: Connect a monitor to the LOCAL port on the transmitter

unitusingaTrippLiteP568-SeriesHigh-SpeedHDMICable.

Connecttheexternalpowersupplytothetransmitterunitandplugthe

transmitterunitintoaTrippLiteSurgeSuppressor,PowerDistribution

Unit(PDU),orUninterruptiblePowerSupply(UPS).ThegreenRJ45LED

illuminatestoindicatethattheunitisreceivingpowerfromtheexternal

power supply.

UsingCat5e/6cable,connecttheRJ45portonthetransmitterunit

marked OUTPUTtotheRJ45portonthereceiverunitmarkedINPUT.

Connect theexternal power supply tothe receiver unit andplug the

receiverunitintoaTrippLiteSurgeSuppressor,PowerDistributionUnit

(PDU), or Uninterruptible Power Supply (UPS). The green RJ45 LED

illuminatestoindicatethattheunitisreceivingpowerfromtheexternal

power supply.

Connect a monitor to the OUTPUT 1 port on the receiver unit using a

TrippLiteP568-SeriesHigh-SpeedHDMIcable.

Repeat step 7 for the OUTPUT 2 port on the receiver unit.

Turnonthepowertotheconnecteddevices.TheorangeRJ45LED’s

on the transmitter and receiver units illuminate to indicate that a

signalisbeingreceivedfromtheHDMIsource.Thevideoimagewill

now be displayed on the connected monitors.

Ifnecessary,usetheEqualizationcontrolonthereceiverunittoadjust

the video image. Note: An improper Equalization setting can cause

the monitor not to display an image at all. Try each setting until an

acceptable image is displayed.

13-08-043 93-32D0.indd 6 8/28/2013 2:17:38 PM

OPTIONAL LOCAL

MONITOR

B126-2A1 LOCAL

TRANSMITTER

B126-2A1 REMOTE

RECEIVER

B126-110 REMOTE

REPEATER

B126-110 REMOTE

REPEATER

B126-110 REMOTE

REPEATER

Up to 175 ft. at 1080i (60Hz)

Up to 125 ft. at 1080p (60Hz)

Up to 175 ft. at 1080i (60Hz)

Up to 125 ft. at 1080p (60Hz)

BLU-RAY

Up to 175 ft. at 1080i (60Hz)

Up to 125 ft. at 1080p (60Hz)

Up to 175 ft. at 1080i (60Hz)

Up to 125 ft. at 1080p (60Hz)

MONITOR 1 MONITOR 2

1 x 2 Extender Kit with

Remote/Repeater Installation

Notes:

1. Test to make sure that the entire installation works properly before

running cables through ceilings/walls.

2. The diagram below shows the maximum extension distance when using

either Cat5e or Cat6 cabling. 24 AWG, solid wire Cat5e/6 cable, such

as Tripp Lite’s N202-Series, is required to achieve maximum distance

and resolution.

3. The B126-2A1 is set to transmit a stereo audio signal by default.

Press the Audio button on the transmitter unit to switch to 7.1-channel

surround sound audio. (7.1-channel surround sound signal will be

Multi-Channel or PCM)

MakesurealldevicesbeingconnectedarepoweredOFF.

ConnecttheHDMIsourcetotheINPUT port on the transmitter unit

usingaTrippLiteP568-SeriesHigh-SpeedHDMICable.

Optional: Connect a monitor to the LOCAL port on the transmitter

unitusingaTrippLiteP568-SeriesHigh-SpeedHDMICable.

13-08-043 93-32D0.indd 7 8/28/2013 2:17:39 PM

Connecttheexternalpowersupplytothetransmitterunitandplugthe

transmitterunitintoaTrippLiteSurgeSuppressor,PowerDistribution

Unit(PDU),orUninterruptiblePowerSupply(UPS).ThegreenRJ45LED

illuminatestoindicatethattheunitisreceivingpowerfromtheexternal

power supply.

UsingCat5e/6cable,connecttheRJ45portonthetransmitterunit

marked OUTPUT to the RJ45 port on the B126-110 repeater unit

marked INPUT.

Connect a monitor to theHDMI OUTPUT port on the repeater unit

usingaTrippLiteP568-SeriesHigh-SpeedHDMICable.

Connecttheexternalpowersupplytotherepeaterunitandplugthe

repeaterunit intoa TrippLite SurgeSuppressor,PowerDistribution

Unit(PDU),orUninterruptiblePowerSupply(UPS).Thegreenpower

andthegreenRJ45LEDswillilluminatetoindicatethattheunitis

receivingpowerfromtheexternalpowersupply.

Upto4unitscanbedaisy-chained(3repeatersand1activereceiver).To

addadditionalrepeaterunits,proceedtostep8.Tonishyourinstallation

withtheB126-2A1receiverunit,proceedtostep11.

UsingCat5e/6cable,connecttheRJ45portontherepeaterunitmarked

OUTPUTtotheRJ45portonasecondrepeaterunitmarkedINPUT.

Connect a monitor to theHDMI OUTPUT port on the repeater unit

usingaTrippLiteP568-SeriesHigh-SpeedHDMICable.

Connecttheexternalpowersupplytotherepeaterunitandplugthe

repeaterunit intoa TrippLite SurgeSuppressor,PowerDistribution

Unit(PDU),orUninterruptiblePowerSupply(UPS).Thegreenpower

andthegreenRJ45LEDswillilluminatetoindicatethattheunitis

receivingpowerfromtheexternalpowersupply.

1 x 2 Extender Kit with

Remote/Repeater Installation

13-08-043 93-32D0.indd 8 8/28/2013 2:17:39 PM

Toaddathirdremote/repeaterunit,repeatsteps8through10.Tonish

yourinstallationwiththeB126-2A1receiverunit,proceedtostep11.

Using Cat5e/6 cable, connect the RJ45 port on the repeater unit

marked OUTPUTtotheRJ45portonthereceiverunitmarkedINPUT.

Connect a monitor to the OUTPUT 1 port on the receiver unit using a

TrippLiteP568-SeriesHigh-SpeedHDMIcable.

Repeat step 12 for the OUTPUT 2 port on the receiver unit.

Connecttheexternalpowersupplytothereceiverunitandplugthe

receiver unit into a Tripp Lite Surge Suppressor, Power Distribution

Unit(PDU),orUninterruptiblePowerSupply(UPS).ThegreenRJ45

LEDilluminatestoindicatethatitisreceivingpowerfromtheexternal

power supply.

Turnonthepowertotheconnecteddevices.TheorangeRJ45LEDs

on all units will illuminate to indicate that a signal is being received

fromtheHDMIsource.Thevideoimagewillnowbedisplayedonthe

connected monitors.

Ifnecessary,usetheEqualization control on the repeater and receiver

units to adjust the video image. Note: An improper Equalization

setting can cause the monitor not to display an image at all. Try each

setting until an acceptable image is displayed.

1 x 2 Extender Kit with

Remote/Repeater Installation

13-08-043 93-32D0.indd 9 8/28/2013 2:17:40 PM

Standard Extender/Splitter Installation

Notes:

1. Test to make sure that the entire installation works properly before

running cables through ceilings/walls.

2. 24 AWG, Solid Wire Cat5e/6 cable, such as Tripp Lite’s N202-Series,

is required to achieve maximum distance and resolution.

3. The diagram below shows the maximum extension distance when

using Cat6 cabling. When using Cat5 cabling, the maximum extension

distance is 175 ft. at 1080i (60Hz), and 125 ft. at 1080p (60Hz).

4. The B126-002 and B126-004 are set to transmit a stereo audio

signal by default. Press the Audio button on the transmitter unit to

switch to 7.1-channel surround sound audio. (7.1-channel surround

sound signal will be Multi-Channel or PCM)

5. The diagram below shows the B126-004 transmitter unit. Installation

is the same for the B126-002, except that there are only two output

ports and no local monitor port.

6. Although the installation instructions below mention the B126-2A0 1x2

receiver unit only, Tripp Lite offers several standard receiver units that

can be used in the event that only one monitor is required on the remote

end: B126-1A0, B126-1A0-WP-1, B126-1P0, and B126-1P0-WP-1.

13-08-043 93-32D0.indd 10 8/28/2013 2:17:40 PM

B126-004

OPTIONAL LOCAL

MONITOR

BLU-RAY

B126-2A0B126-2A0

Up to 200 ft. at 1080i @ 60Hz (Cat6)

Up to 150 ft. at 1080p @ 60Hz (Cat6)

HDMI OVER Cat5

1 x 2 EXTENDER

REMOTE UNIT

MODEL: B126-2A0

HDMI OVER Cat5

1 x 2 EXTENDER

REMOTE UNIT

MODEL: B126-2A0

HDMI OVER Cat5

1 x 2 EXTENDER

REMOTE UNIT

MODEL: B126-2A0

HDMI OVER Cat5

1 x 2 EXTENDER

REMOTE UNIT

MODEL: B126-2A0

Standard Extender/Splitter Installation

MakesurealldevicesbeingconnectedarepoweredOFF.

Connect the HDMI source to the INPUT port on a B126-002 or

B126-004transmitterunitusingaTrippLiteP568-SeriesHigh-Speed

HDMICable.

Optional for B126-004: Connect a monitor to the LOCAL port on the

transmitterunitusingaTrippLiteP568-SeriesHigh-SpeedHDMICable.

Connecttheexternalpowersupplytothetransmitterunitandplugthe

transmitterunitintoaTrippLiteSurgeSuppressor,PowerDistribution

Unit(PDU),orUninterruptiblePowerSupply(UPS).ThegreenRJ45

LEDsontheB126-002andB126-004,andtheredpowerLEDon

the B126-004 will illuminate to indicate that the unit is receiving

powerfromtheexternalpowersupply.

UsingCat5e/6cable,connectaRJ45OUTPUT port on the transmitter

unittotheRJ45INPUTportontheB126-2A01x2receiverunit.

Repeatstep5toaddreceiverunitstotheremainingRJ45OUTPUT

ports on the transmitter unit.

13-08-043 93-32D0.indd 11 8/28/2013 2:17:40 PM

Connect theexternal power supply tothe receiver unit andplug the

receiverunitintoaTrippLiteSurgeSuppressor,PowerDistributionUnit

(PDU), or Uninterruptible Power Supply (UPS). The green RJ45 LED

illuminatestoindicatethattheunitisreceivingpowerfromtheexternal

power supply.

Connect a monitor to the OUTPUT 1 port on the receiver unit using a

TrippLiteP568-SeriesHigh-SpeedHDMICable.

Repeatstep8fortheOUTPUT 2 port on the receiver unit.

Turnonthepowertotheconnecteddevices.TheorangeRJ45LEDs

on the transmitter and receiver units will illuminate to indicate that

a signalis being received from the HDMI source.The video image

should now be displayed on the connected monitors.

Ifnecessary,usetheEqualizationcontrolonthereceiverunittoadjust

the video image. Note: An improper Equalization setting can cause

the monitor not to display an image at all. Try each setting until an

acceptable image is displayed.

Standard Extender/Splitter Installation

13-08-043 93-32D0.indd 12 8/28/2013 2:17:40 PM

Extender/Splitter with

Remote/Repeater Installation

Notes:

1. Test to make sure that the entire installation works properly before

running cables through ceilings/walls.

2. The diagram below shows the maximum extension distance when using

either Cat5e or Cat6 cabling. 24 AWG, solid wire Cat5e/6 cable, such

as Tripp Lite’s N202-Series, is required to achieve maximum distance

and resolution.

3. The B126-002 and B126-004 are set to transmit a stereo audio

signal by default. Press the Audio button on the transmitter unit to

switch to 7.1-channel surround sound audio. (7.1-channel surround

sound signal will be Multi-Channel or PCM)

4. The diagram below shows the B126-004 transmitter unit. Installation

is the same for the B126-002, except that there are only two output

ports and no local monitor port.

5. Although the installation instructions below mention the B126-2A0

1x2 receiver unit only, Tripp Lite offers two additional active receivers

that can be used in the event that only one monitor is needed at the

end of a repeater chain: B126-1A0 and B126-1A0-WP-1.

13-08-043 93-32D0.indd 13 8/28/2013 2:17:40 PM

OPTIONAL LOCAL

MONITOR

B126-004 LOCAL

TRANSMITTER

B126-110 REMOTE/

REPEATER

B126-110 REMOTE/

REPEATER

B126-110 REMOTE/

REPEATER

Up to 175 ft. at 1080i (60Hz)

Up to 125 ft. at 1080p (60Hz)

Up to 175 ft. at 1080i (60Hz)

Up to 125 ft. at 1080p (60Hz)

BLU-RAY

B126-110 REMOTE/

REPEATER

B126-110 REMOTE/

REPEATER

B126-110 REMOTE/

REPEATER

B126-110 REMOTE/

REPEATER

B126-110 REMOTE/

REPEATER

B126-110 REMOTE/

REPEATER

B126-2A0

REMOTE RECEIVER

B126-2A0

REMOTE RECEIVER

B126-2A0

REMOTE RECEIVER

B126-2A0

REMOTE RECEIVER

B126-110 REMOTE/

REPEATER

B126-110 REMOTE/

REPEATER

B126-110 REMOTE/

REPEATER

HDMI OVER Cat5

1 x 2 EXTENDER

REMOTE UNIT

MODEL: B126-2A0

HDMI OVER Cat5

1 x 2 EXTENDER

REMOTE UNIT

MODEL: B126-2A0

HDMI OVER Cat5

1 x 2 EXTENDER

REMOTE UNIT

MODEL: B126-2A0

HDMI OVER Cat5

1 x 2 EXTENDER

REMOTE UNIT

MODEL: B126-2A0

MakesurealldevicesbeingconnectedarepoweredOFF.

Connect the HDMI source to the INPUT port on a B126-002 or

B126-004transmitterunitusingaTrippLiteP568-SeriesHigh-Speed

HDMICable.

Optional for B126-004: Connect a monitor to the LOCAL port on

thetransmitterunitusingaTrippLiteP568-SeriesHigh-SpeedHDMI

Cable.

Connecttheexternalpowersupplytothetransmitterunitandplugthe

transmitterunitintoaTrippLiteSurgeSuppressor,PowerDistribution

Unit(PDU),orUninterruptiblePowerSupply(UPS).ThegreenRJ45

LEDs on the B126-002 and B126-004, and the red LED on the

B126-004willilluminatetoindicatethattheunitisreceivingpower

fromtheexternalpowersupply.

Extender/Splitter with

Remote/Repeater Installation

13-08-043 93-32D0.indd 14 8/28/2013 2:17:41 PM

UsingCat5e/6cable,connectaRJ45OUTPUT port on the transmitter

unittotheRJ45INPUTportontheB126-110repeaterunit.

Connect a monitor to theHDMI OUTPUT port on the repeater unit

usingaTrippLiteP568-SeriesHigh-SpeedHDMICable.

Connecttheexternalpower supplytotheremote/repeater unitand

plug the remote/repeater unit into a Tripp Lite Surge Suppressor,

PowerDistributionUnit(PDU),orUninterruptiblePowerSupply(UPS).

ThegreenpowerandRJ45LEDswillilluminatetoindicatethatthe

unitisreceivingpowerfromtheexternalpowersupply.

Upto4unitscanbedaisy-chained(3repeatersand1activereceiver).To

addadditionalrepeaterunits,proceedtostep8.Tonishyourinstallation

withaB126-2A01x2receiverunit,proceedtostep11.

UsingCat5e/6cable,connecttheRJ45portontherepeaterunitmarked

OUTPUTtotheRJ45portonasecondrepeaterunitmarkedINPUT.

Connect a monitor to theHDMI OUTPUT port on the repeater unit

usingaTrippLiteP568-SeriesHigh-SpeedHDMICable.

Connecttheexternalpower supplytotheremote/repeater unitand

plug the remote/repeater unit into a Tripp Lite Surge Suppressor,

PowerDistributionUnit(PDU),orUninterruptiblePowerSupply(UPS).

ThegreenpowerandgreenRJ45LEDswillilluminatetoindicatethat

theunitisreceivingpowerfromtheexternalpowersupply.

Toaddathirdremote/repeaterunit,repeatsteps8through10.Tonish

yourinstallationwithaB126-2A01x2receiverunit,proceedtostep11.

Extender/Splitter with

Remote/Repeater Installation

13-08-043 93-32D0.indd 15 8/28/2013 2:17:41 PM

Using Cat5e/6 cable, connect the RJ45 port on the repeater unit

marked OUTPUT to the RJ45 port on the B126-2A0 receiver unit

marked INPUT.

Connect a monitor to the OUTPUT 1 port on the receiver unit using a

TrippLiteP568-SeriesHigh-SpeedHDMICable.

Repeat step 12 for the OUTPUT 2 port on the receiver unit.

Connecttheexternalpowersupplytothereceiverunitandplugthe

receiver unit into a Tripp Lite Surge Suppressor, Power Distribution

Unit(PDU),orUninterruptiblePowerSupply(UPS).ThegreenRJ45

LEDilluminatestoindicatethatitisreceivingpowerfromtheexternal

power supply.

Repeatsteps5through14foreachadditionalRJ45OUTPUT port on

the transmitter unit.

Turnonthepowertotheconnecteddevices.TheorangeRJ45LEDs

on all units will illuminate to indicate that a signal is being received

fromtheHDMIsource.Thevideoimageshouldnowbedisplayedon

the connected monitors.

Ifnecessary,usetheEqualization control on the repeater and receiver

units to adjust the video image. Note: An improper Equalization

setting can cause the monitor not to display an image at all. Try each

setting until an acceptable image is displayed.

Extender/Splitter with

Remote/Repeater Installation

13-08-043 93-32D0.indd 16 8/28/2013 2:17:41 PM

Troubleshooting

Ifyouareunabletogetanacceptableimageafterfollowingtheinstallation

instructions,trythesetroubleshootingtips:

Are the external power supplies that came with the product

connected and plugged into a working power source? For the

product to function properly, it must be connected to and receiving

powerfromtheexternalpowersupply.

Was the power to the connected devices turned off prior to

installation?Ifnot,restartthem.

Have you adjusted the Equalization setting on the repeater and/

or receiver units?Therearebuilt-inEqualizationadjustmentknobson

everyrepeaterandactivereceiverthatcanbeadjustedtoobtainthe

bestpicturequality.Usetheminiscrewdriverincludedwiththeproduct

toadjustthissettinguntilanacceptableimageisdisplayed.Note: An

improper Equalization setting can cause the monitor not to display an

image at all. Try each setting until an acceptable image is displayed.

What resolution are you trying to reach?Tripp Lite’sHDMIover

Cat5 extenders are tested to support up to 1080p (60Hz) video

resolution (See the Product Features section or the installation

diagrams in this manual for details on the maximum distance and

resolutionwhenusingtherepeaterandthedifferentreceivers).The

shortertheextensiondistance,thehighertheresolutionyouwillbe

abletoobtain.Ifyouarenotabletogetanacceptableimageafter

adjustingtheEqualizationsetting,tryloweringyourcomputer’svideo

resolutionoradjustingtherefreshrate.

13-08-043 93-32D0.indd 17 8/28/2013 2:17:41 PM

What type of cabling are you using?Inferiorcablingcanresultinpoor

performance, so it is important that you use cables that support the video

resolution you are trying to obtain. To achieve maximum distance and

resolution,24AWGsolidwireUTPcablemustbeused.TrippLite’sN202-

SeriesCat6Cablesaremadewith24AWGsolidwire,asaretheN022-

01K-GY(Cat5)andN222-01K-GYBulkCables.Also,theHDMIcablesyou

areusingmustsupporttheresolutionyouaretryingtoobtain.Inexpensive,

lowquality HDMIcables maynot supportthe maximumresolution. Itis

recommended that you use Tripp Lite’sP568-Series High-SpeedHDMI

Cablesthatarepre-testedtoworkwithallB126-Seriesextenderproducts.

Test your cables to ensure they are working properly. Try

connecting your HDMI cables between a source and monitor that

you know works to see if the cable is functioning. For Cat5e/6

cabling, connect it between a computer and a network to verify that it

establishes a network connection.

Do you have any patch panels or other devices in between

the transmitter, repeater, and receiver units? TrippLite’s HDMI

overCat5 extenderproductsare designedtobe connecteddirectly

from thetransmitter to therepeater and/or receiver viaUTP cable.

The more connection points that are in between the source and the

remote monitor, the more likely signal degradation will occur, causing

poorperformance.Ifyouhaveapatchpanelorifanotherdeviceis

being used, it should be removed from the installation.

Check your cabling for any damages that may have occurred

during installation.Ifacableconnectorisloosenedasaresultofbeing

pulledthroughceilings/walls,orthecablejacketisdamaged,causingthe

wiringtobeexposed,youwillnotachievemaximumperformance.

Are the transmitter, repeater, and/or receiver located in an area

that exposes them to higher temperatures? If the product is

overheated, it will not function properly.

Troubleshooting

13-08-043 93-32D0.indd 18 8/28/2013 2:17:41 PM

Warranty & Warranty Registration

1-Year Limited Warranty

TRIPP LITE warrants its products to be free from defects in materials and workmanship for a

periodofone(1)yearfromthedateofinitialpurchase.TRIPPLITE’sobligationunderthiswarranty

is limited to repairing or replacing (at its sole option) any such defective products. To obtain

service under this warranty, youmust obtain a Returned Material Authorization(RMA) number

fromTRIPPLITEoranauthorizedTRIPPLITEservicecenter.ProductsmustbereturnedtoTRIPP

LITE or an authorized TRIPP LITE service center with transportation charges prepaid and must

be accompanied by a brief description of the problem encountered and proof of date and place

ofpurchase.Thiswarrantydoesnotapplytoequipmentwhichhasbeendamagedbyaccident,

negligenceormisapplicationorhasbeenalteredormodiedinanyway.

EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Somestatesdonotpermitlimitationorexclusionofimpliedwarranties;therefore,theaforesaid

limitation(s)orexclusion(s)maynotapplytothepurchaser.

EXCEPTASPROVIDEDABOVE,INNOEVENTWILLTRIPPLITEBELIABLEFORDIRECT,INDIRECT,

SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS

PRODUCT, EVEN IF ADVISED OF THE POSSIBILITYOF SUCH DAMAGE. Specically, TRIPP LITE

is not liable for any costs, such as lost prots or revenue, loss of equipment, loss of use of

equipment,lossofsoftware,lossofdata,costsofsubstitutes,claimsbythirdparties,orotherwise.

WARRANTY REGISTRATION

Visit www.tripplite.com/warrantytoday to register the warranty for your new Tripp Lite product.

You’llbeautomaticallyenteredintoadrawingforachancetowinaFREETrippLiteproduct!*

*Nopurchasenecessary.Voidwhereprohibited.Somerestrictionsapply.Seewebsitefordetails.

WEEE Compliance Information for Tripp Lite Customers and Recyclers

(European Union)

Under the Waste Electrical and Electronic Equipment (WEEE) Directive and

implementing regulations, when customers buy new electrical and electronic

equipmentfromTrippLitetheyareentitledto:

• Sendoldequipmentforrecyclingonaone-for-one,like-for-likebasis(thisvaries

dependingonthecountry)

• Sendthenewequipmentbackforrecyclingwhenthisultimatelybecomeswaste

13-08-043 93-32D0.indd 19 8/28/2013 2:17:42 PM

1111 W. 35th Street, Chicago, IL 60609 USA

www.tripplite.com/support

13-08-043•9332D0_RevA

FCC Notice, Class B

This device complies with part 15 of the FCC Rules. Operationis subject to the following two

conditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustaccept

any interference received, including interference that may cause undesired operation.

Note:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

usesandcanradiateradiofrequencyenergyand,ifnot installedand usedin accordancewith

theinstructions,maycauseharmfulinterferencetoradiocommunications.However,thereisno

guaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescause

harmful interference to radio or television reception, which can be determined by turning the

equipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreof

thefollowingmeasures:

• Reorientorrelocatethereceivingantenna.

• Increasetheseparationbetweentheequipmentandreceiver.

• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiveris

connected.

• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

AnychangesormodicationstothisequipmentnotexpresslyapprovedbyTrippLitecouldvoidthe

user’sauthoritytooperatethisequipment.

WARNING

Useofthisequipmentinlifesupportapplicationswherefailureofthisequipmentcanreasonably

beexpectedtocausethefailureofthelifesupportequipmentortosignicantlyaffectitssafety

oreffectivenessisnotrecommended.Donotusethisequipmentinthepresenceofaammable

anestheticmixturewithair,oxygenornitrousoxide.

TrippLitefollowsapolicyofcontinuousimprovement.Productspecicationsaresubjecttochange

without notice.

13-08-043 93-32D0.indd 20 8/28/2013 2:17:42 PM

Tripp Lite B126-2A0, B126-2A1, HDMI Over Cat5 1x2 Extenders Owner's manual

Related papers

Other documents