Microdigital MDS-H209 Installation & Operating Manual

Mega-pixel Speed Dome Camera

P/N : 388066210

PRINTED IN KOREA

Distributed by

INSTALLATION / OPERATING MANUAL

Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for future use

02

Outdoor Speed PTZ Dome Camera System Use's Guide

03

Outdoor Speed PTZ Dome Camera System Use's Guide

1. 1 Important Safety Instruction

•

Read these instructions.

•

Pay attention on all the warnings.

•

Follow all instructions.

•

Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

•

Do not dissemble or insert foreign objects.

•

Do not install near any heat sources such as radiation, beat registers, stoves, or other apparatus.

(Including amplifiers) that produce heat.

•

Do not aim the camera at the sun or any other strong light source.

•

Do not install the camera in intermittent lighting environments.

•

Only use attachments/accessories specified by the manufacturer.

•

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use caution when moving the cart/apparatus combination

to avoid injury from tip-over.

•

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

•

Installation should be done only by qualified personnel and conform to all local codes.

•

Installation should be done in a place strong enough to hold it.

•

Use only installation methods and materials capable of supporting four times the maximum specified load.

•

It is designed for indoor use only and it must not be installed where exposed to rain and moisture

without additional outdoor housing and bracket.

•

To prevent damage from water leakage when installing a mount outdoors on a roof or wall,

apply sealant around the bolt holes between the mount and mounting surface.

•

These instructions are for use by qualified service personnel only. To reduce the risk of electric shock

do not perform any servicing other that contained in the operating instructions unless you are qualified

to do so.

•

Only use replacement parts recommended by manufacturer.

ad these instructions.

1. PRECAUTIONSTABLE OF CONTENTS

3p.

4p.

5p.

6p.

8p.

9p.

10p.

12p.

29p.

35p.

45p.

46p.

47p.

48p.

49p.

50p.

51p.

1. PRECAUTIONS

1. 1 Important Safety Instruction ...................................................................................

2. GETTING STARTED

2. 1 Descriptions ..........................................................................................................

2. 2 Unpacking ..............................................................................................................

2. 3 Outdoor Speed PTZ Dome Camera Module .............................................................

2. 4 DIP Switch Setting .................................................................................................

2. 5 Cable Connection ...................................................................................................

3. INSTALLATION

3. 1 Before Installation ..................................................................................................

3. 2 Wall Mounting ........................................................................................................

4. ON-SCREEN DISPLAY PROGRAM MENU

4. 1 Powering ON ..........................................................................................................

4. 2 Establishing Camera Control ...................................................................................

4. 3 Motion Setting .......................................................................................................

4. 4 Dome Setting .........................................................................................................

4. 5 Camera Setting ......................................................................................................

4. 6 Clear Setting ..........................................................................................................

4. 7 PTZ Reset ..............................................................................................................

5. SPECIFICATION

5. 1 Mechanism Specification .......................................................................................

5. 2 Camera Specification..............................................................................................

6. DIMENSION

6. 1 DIMENSION ..........................................................................................................

7. CONFIGURATION

7. 1 Connecting to Keyboard with DVR -1 ......................................................................

7. 2 Connecting to Keyboard with DVR -2 ......................................................................

7. 3 Connecting to Keyboard with DVR -3 ......................................................................

04

Outdoor Speed PTZ Dome Camera System Use's Guide

05

Outdoor Speed PTZ Dome Camera System Use's Guide

2. 1 Descriptions

This Speed Dome Camera series are an outdoor speed PTZ dome system designed for IP66 applications,

especially, whether it is raining, snowing or sunny day, this PTZ dome series delivers superior performance.

The PTZ Dome series is one unit of housing with pole, corner, wall or recessed ceiling mounts. It includes

a high resolution color camera; video output capability through coaxial cable; pan/tilt control using

Pelco D or P protocol with on-screen programming.

2. 2 Unpacking

The following parts are supplied with the outdoor speed PTZ dome system.

2. GETTING STARTED

2. 3 Outdoor Speed PTZ dome camera Module

2. 3. 1 Outdoor Speed PTZ dome camera Models

1/3" Panasonic CMOS Sensor optical 20×with WDR

IMPORTANT> When placing order, please make sure of which the below optional selection for the default

camera package is proper for your application.

- Optional 1: Smoke dome cover / Clear dome cover

- Optional 2: PAL type / NTSC type

Dome Drive Dome Body (Housing) Housing Cover Housing

Analog Video CableHousing Controller User’s Guide Screws

Security Tool L-Wrench Mount Cap

06

Outdoor Speed PTZ Dome Camera System User’s Guide

07

Outdoor Speed PTZ Dome Camera System User’s Guide

2. 4 DIP Switch Setting

1.ADDRESS Setting

SW1 : 100 digit of ID(0~2)

SW2 : 10 digit of ID(0~9)

SW3 : 1 digit of ID(0~9)

FACTORY : Support IP version only.

Press more than 10 Seconds

FACTORY : Support IP version only.

Press more than 10 Seconds.

1 2 3

NumX10

NumX1

NumX100

2.SET1, SET2 DIP Switch setting

3.Function Button

OSD MENU OPEN/CLOSE STATUS

PTZ MODE SWITCH:MENU OPEN/CLOSE

SET PRESS+WIDE SWITCH:Zoom out

SET PRESS+TELE SWITCH:Zoom in

SET PRESS+FAR SWITCH:Setting focus

SET PRESS+NEAR SWITCH:Setting focus

SET SWITCH : MENU SELECT

1

237

5

4

6

1

2

3

4

5

6

7

4.POWER, COMM, ALARM1,RLY1, ALARM2, RLY2, EXT VIDEO

POWER:Power Voltage

COMM:RS-485/RS-422 control system

ALARM1,2:Alarm function enables the camera move to the programmed

Preset position when there is Alarm trigger.

Alarm No. : Max. 8 Alarms can be stored.

Label : The each Alarm can have its own label name.

Preset No. : Assign the Preset No. to run when alarm is triggered.

RLY1,2:NC-Normal Close

NO-Normal Open

CO-COMM

EXT VIDEO:Connect the video out connector to the monitor or DVR

HD-SDI:Connect the HD-SDI connector to the monitor or DVR

1

2

3

4

5

1

23 4 5

AC24V 3A

6

Mega-pixel Setting

3.Function Button

OSD OPEN/CLOSE STATUS

PTZ MODE SWITCH:MENU OPEN/CLOSE

SET SHORT PRESS+WIDE SWITCH:Zoom out

SET SHORT PRESS+TELE SWITCH:Zoom in

SET SHORT PRESS+FAR SWITCH:Setting focus

SET SHORT PRESS+NEAR SWITCH:Setting focus

SET SWITCH : MENU SELECT

①

②

③

④

⑤

⑥

⑦

1

23 7

5

4

6

2.SET1, SET2 DIP Switch setting

000 PelcoD V5

001 PelcoP

010 WTX

011 EZ

100 G

101 NC

110 NC

111 NC

000 2400

001 4800

010 9600

011 19200

100 38400

101 57600

110 115200

111 NC

00 1080p30(25)

01 1080i60(50)

10 720p50(60)

11 1080i59

0 OFF

1 ON

0 OFF

1 ON

0 OFF

1 Program Mode

0 RS-422

1 RS-485

00 NONE

01 EVEN

10 ODD

11 NC

12345678 12345678

ON

OFF

1.ADDRESS Setting

SW1 : 100 digit of ID(0~2)

SW2 : 10 digit of ID(0~9)

SW3 : 1 digit of ID(0~9)

1 2 3

NumX10

NumX1

NumX100

4.POWER, COMM, ALARM1,RLY1, ALARM2, RLY2, EXT VIDEO

POWER: Power Voltage

COMM:RS-485/RS-422 control system

ALARM1,2:Alarm function enables the camera move to the programmed

Preset position when there is Alarm trigger.

Alarm No. : Max. 8 Alarms can be stored.

Label : The each Alarm can have its own label name.

Preset No. : Assign the Preset No. to run when alarm is triggered.

RLY1,2:NC-Normal Close

NO-Normal Open

CO-COMM

EXT VIDEO:Connect the video out connector to the monitor or DVR

HD-SDI:Connect the HD-SDI connector to the monitor or DVR

1

2

3

4

5

1

23 4 5

AC24V 3A

6

12 3 4 5 6 7 8

1.PROTOCOL

2.BAUDRATE

3.PARITY

4.VIDEO TYPE

5.IP SELECT

6.RS TYPE

7.RS LOOP

8.BOOT0

12345678 12345678

ON

OFF

12 3 4 5 6 7 8

000 PelcoD V5

001 PelcoP

010 WTX

011 EZ

100 G

101 NC

110 NC

111 NC

000 2400

001 4800

010 9600

011 19200

100 38400

101 57600

110 115200

111 NC

00 1080p30(25)

01 1080i60(50)

10 720p50(60)

11 1080i59

0 OFF

1 ON

0 OFF

1 ON

0 OFF

1 Program Mode

0 RS-422

1 RS-485

00 NONE

01 EVEN

10 ODD

11 NC

1.PROTOCOL

2.BAUDRATE

3.PARITY

4.VIDEO TYPE

5.IP SELECT

6.RS TYPE

7.RS LOOP

8.BOOT0

08

Outdoor Speed PTZ Dome Camera System User’s Guide

09

Outdoor Speed PTZ Dome Camera System User’s Guide

2. 5 Cable connection

2. 5. 2 RS-485/RS-422 Connection

2. 5. 1 Power/Data communication cable connection

RS-422/485 connection

The PTZ can be remotely controlled by an external device or control system, such as a control

keyboard or DVR, using RS-485 half-duplex, RS-422 duplex or simplex serial communication signals.

Connect marked RX+, RX- to TX+ and TX- of the RS-485 control system.

If control system is RS-422, connect TX+,TX- of controller to RX+ and RX- of the PTZ Camera series.

And also connect the TX+, TX- to RX+, RX- of the control device respectively. Total length

of the cable for communication should not exceed 1.2Km.

2. 5. 3 HD-SDI Output connection

Connect the HD-SDI out (BNC) connector to the monitor or video input of DVR. Video cable and

RS-485/422 communication cable are not provided in this product's package.

Power connection

- Connect the power of AC 24V

- Power Terminal: 2PIN

- Com Terminal: 4PIN

3.Installtion

3. 1 Before Installation

- The following steps of installation and connection work should be done by qualified service personnel

or system installers and should conform to all local codes.

- Be sure to switch the camera off before installation is completed.

- Do not install the camera near the air outlet of an air conditioner.

- Before installation, set the dome system with Dip switch on the back side of the mechanism part, and

assemble the mechanism and housing according to the below instruction

The 2 clamp wires were used to fix mechanism to prevent

any damages in shipping.

When this camera is being installed, The clamp wires have to be

Removed from PTZ SET.

3. 2 Wall Mounting

1 Set the housing controller on the position to install the product.

Connect the heater cable and fan cable to the PTZ connector.

* Caution: Do not assemble the PTZ motor face to the fan.

2 Connect the dome cover and housing with the safety wire.

Fasten the dome cover on the housing by using screws.

3 Connect the PTZ housing and housing controller with the safety wire.

4 Connect the main cable to the PTZ housing and insert the cable into the housing controller.

* Caution: Be careful not to be kinked the cable and turn through the housing to the right .

Open

Close

POWER LAN PORT

MIC SPK

HD-SDI IP_DI

GND IP_DOB

IP_DOA

Mega-pixel IP

10

Outdoor Speed PTZ Dome Camera System User’s Guide

11

Outdoor Speed PTZ Dome Camera System User’s Guide

4. 1 Powering On

When turning the camera power on, there is a ten (10) second pause before the camera starts

its homing phase. During the homing phase the camera pans left and right and tilts up and down. It also

adjusts the lens focus.

4. 2 Establishing Camera Control

The most common way to interface with the camera is using a keyboard and on-screen display (OSD)

menu. This method is the most common and is covered in this manual.

4. 2. 1 Basic Keyboard Operation

The following tables summarize the basic operations for a standard keyboard and the functions available

to control the PTZ camera.

Table 1. 1 Typical Keyboard Functions

Table 2. 1 Typical Keyboard Controls for the speed PTZ dome camera system

4. ON-SCREEN DISPLAY PROGRAM MENU

Typical Keyboard Features Usage

Function Keys

Number Keys

Camera Key

Enter Key

Focus Key (Or Near Key)

Iris Key

Key LEDs

LCD

Joystick

Selects a specific control setting

Inputs a number from 0 to 9.

Selects a camera number

Inputs a selection

Sets the lens focus or make a menu selection in OSD menu.

Sets the lens iris setting or makes a menu selection in OSD mode.

Indicates an active key

Displays the current status

Controls a pan/tilt/zoom (PTZ) series

Dome Operation How to Control

To Pan Side to Side

To Tilt Up and Down

To Zoom In

To Zoom Out

Move the joystick left or right.

Move the joystick forward and back.

Twist the joystick clockwise.

Twist the joystick counterclockwise.

The PTZ dome camera is programmed through the on-screen display (OSD) menus.

To access the OSD menus, you must open the main Setup Menu.

4. 2. 3 Setup Program OSD Menu From Keyborad.

The main Setup Menu provides access to all programmable PTZ settings.

4. 2. 2 Keyboard Commands

- Keyboard control commands are composed of a sequence of two (2) inputs with the following

convention: 1) a Command number key(s) + 2) a Function key.

- Command numbers range from 1 to 999.

- Refer to the keyboard manual for the key naming conventions in detail.

4. 2. 4 Go into the camera setup 0SD Menu

Press key “1” and keep pressing the “MENU” key for approximately 3 seconds, or press key “95” and

press “Preset” key to go into the set-up menu. Setup menus are shown in the diagram below. You can

adapt the camera to your requirements by setting up the respective items in these menus.

4. 2. 5 OSD Menu tree

027,210(18

35(6(7

7285

6&$1

3$77(51

$5($

$/$50

35,9$&<

%$&.(;,7

୅

1($55,*+7୅35(6(7!

୅

'20(0(18

7,7/(

32:(583$&7,21

3$5.$&7,21

',63/$<212))

'20(68%0(18

7(036(7

)$&725<6(7

6$9(%$&.(;,7

୅

1($55,*+7୅7,7/(6(7!

21

୅

=22002'(

)2&8602'(

:+,7(%$/

$872(;3

:'502'(

63(&,$/

&$0(5$5(6(7

1($55,*+7ୄ=22002'(!

୅

6$9(%$&.(;,7

&$0(5$0(18 &/($50(18

35(6(7

7285

6&$1

3$77(1

$5($

$/$50

35,9$&<

%$&.(;,7

୅

1($55,*+7୅35(6(7!

୅

0$,10(18

027,21

'20(

&$0(5$

&/($5

37=5(6(7

(;,7

1($55,*+7୅027,21!

12

Outdoor Speed PTZ Dome Camera System User’s Guide

13

Outdoor Speed PTZ Dome Camera System User’s Guide

4. 3 Motion Setting

The initialize screen is shown up to check address, version,

protocol and video when the power on.

MAIN MENU

< NEAR / RIGHT → PRESET >

MOTION

▶

DOME

▶

CAMERA

▶

CLEAR

▶

PTZ RESET

BACK EXIT

The preset function is that the camera memorizes

positions of the pan/tilt and zoom. This function is

a representative function of the speed dome which

can find memorized preset positions just by selecting

the preset No. A Maximum of 255 Preset positions

are toured in

order.

4. 3. 1 Preset

Preset Quick Operating Guide

Set Preset : 1~255 + 3sec.

Go to Preset : 1~255 +

PRESET

PRESET MENU

< NEAR / RIGHT → PRESET NO >

PRESET NO : 01 DEFINE

LABEL :

POSITION : XXX . X, XXX. X

FOCUS : AUTO

SAVE CLR BACK EXIT

PRESET SELECT 1

(1) Select the Preset number

P01 : Defined Preset number / 01 : Undefined Preset number

Move : Select : NEAR

MOTION MENU

< NEAR / RIGHT → PRESET >

PRESET

▶

TOUR

▶

SCAN

▶

PATTERN

▶

ALARM

▶

AREA

▶

PRIVACY

▶

BACK EXIT

001 002 003 004 005 006

007 008 009 010 011 012

013 014 015 016 017 018

019 020 021 022 023 024

025 026 027 028 029 030

031 032 033 034 035 036

037 038 039 040 041 042

043 044 045 046 047 048

049 050 051 052 053 054

<SEL

▶

NEAR /MOVE & JOYSTICK>

INITIALIZE

PTZID

FIRMWARE

V-FORMAT

CVBS

PROTOCOL

BUADRATE

CAMERA

>>PAN OFFSET. . . . . PASS

>>TILT OFFSET. . . . . PASS

NORMAL SETTING . . . . . . WAIT

: 001

: X.XX

: 1080p30

: NTSC

: PELCO D V1.0

: 2400 ,N.1

: FCB EH

PRESET MENU

< NEAR / RIGHT

▶

PRESET NO >

PRESET NO : 01 DEFINE

LABEL :

POSITION : XXX . X, XXX. X

FOCUS : AUTO

SAVE CLR BACK EXIT

PRESET MENU

< NEAR / RIGHT

▶

PRESET NO >

PRESET NO : 01 DEFINE

LABEL :

POSITION : XXX .X , XXX. X

FOCUS : AUTO

SAVE CLR BACK EXIT

PRESET MENU

< NEAR / RIGHT

▶

PRESET NO >

PRESET NO : 01 DEFINE

LABEL :

POSITION : 000. 0 ,000. 0

FOCUS : AUTO

SAVE CLR BACK EXIT

(4) Select the focus mode for Preset

PRESET POSITION

(3) Define the Preset position

① Select the Position menu

or

NEAR

② Move and set the position ③ Set & Back

NEAR

PRESET LABEL EDIT ( 01 )

< DELETE

▶

WIDE

< STORE

▶

TELE

BACK

▶

NEAR >

MOVE

▶

JOYSTICK >

LABEL : PRESET 01

(2) Set the Preset Label

Move : Select : or or Delete : or

TELE

JOYSTICK

WIDE

JOYSTICK

It’s available to set the desired label, displayed on the executing screen of Preset.

After the label is set, push the NEAR button to exit.

On focus menu, there are 4 modes : Auto, Manual,

Oneshot. It allows detailed settings for the preset.

① Select the Focus menu

or

NEAR

② Move and set the Focus Menu

0 1 2 3 4 5 6 7 8 9 (

) A B C D E F G H I J K

L M N O P Q R S T U V W

X Y Z . / , + - = < >

POSITION : 000. 0 , 000. 0

14

Outdoor Speed PTZ Dome Camera System User’s Guide

15

Outdoor Speed PTZ Dome Camera System User’s Guide

PRESET MENU

< NEAR / RIGHT

▶

PRESET NO >

PRESET NO : 01 DEFINE

LABEL :

POSITION : 000. 0 ,000. 0

FOCUS : AUTO

SAVE CLR BACK EXIT

EXTEND SET ▶

(5) “Save” above setting Pattern data to the memory.

(6) “CLR” means above setting Pattern data will not be

saved and be cleared.

(7) “BACK” means it goes back to the previous

menu :Motion.

(8) “EXIT” means it goes out of MENU.

MAIN MENU

< NEAR / RIGHT → PRESET >

MOTION

▶

DOME

▶

CAMERA

▶

CLEAR

▶

PTZ RESET

BACK EXIT

MOTION MENU

< NEAR / RIGHT

▶

TOUR >

PRESET

▶

TOUR

▶

SCAN

▶

PATTERN

▶

ALARM

▶

AREA

▶

PRIVACY

▶

BACK EXIT

TOUR MENU

< NEAR / RIGHT

▶

TOUR NO >

TOUR NO : 01 UNDEFINE

LABEL :

TOUR EDIT :

SAVE CLR BACK EXIT

TOUR SELECT

< SEL → NEAR / MOVE

▶

JOYSTICK >

01 02 03 04 05 06

07 08

(1) Select the Tour number

T01 : Defined Tour number / 01 : Undefined Tour number

Move : Select : NEAR

The Tour function consists of several presets run by turn. It is also adjusts the moving speed

(1~63 step) and dwell time (1~99secs). Maximum of 8 Tour functions are toured in order.

4. 3. 2 Tour

Tour Quick Operating Guide

Programming : 71~78 + 3sec.

Operating : 71~78 +

TOUR

( 1 Tour can be set for 15 presets. )

※

16

Outdoor Speed PTZ Dome Camera System User’s Guide

17

Outdoor Speed PTZ Dome Camera System User’s Guide

TOUR MENU

< NEAR / RIGHT → TOUR NO >

TOUR NO : 01 DEFINE

LABEL : TOUR 01

TOUR EDIT :

SAVE CLR BACK EXIT

(3) Define the Preset position

① Move to the set-up window

or

NEAR

② Move and set the position ③ Set & Back

NEAR

TOUR EDIT (01)

NO PRESET SPEED DWELL

01 ◀ 01 63 01

02 ◁ 02 63 01

03 ◁ XX XX XX

04 ◁ XX XX XX

05 ◁ XX XX XX

06 ◁ XX XX XX

07 ◁ XX XX XX

08 ◁ XX XX XX

< SEL & NEAR PRESET & LEFT >

(2) Set the Tour Label

Move : Select : or or Delete : or

TELE

JOYSTICK

WIDE

JOYSTICK

It’s available to set the desired label, displayed on the executing screen of Tour.

After the label is set, push the NEAR button to exit.

PRESET SELECT 1

001 002 003 004 005 006

007 008 009 010 011 012

013 014 015 016 017 018

019 020 021 022 023 024

025 026 027 028 029 030

031 032 033 034 035 036

037 038 039 040 041 042

043 044 045 046 047 048

049 050 051 052 053 054

<SEL

▶

NEAR /MOVE & JOYSTICK>

TOUR LABEL EDIT ( 01 )

< DELETE

▶

WIDE

< STORE

▶

TELE

BACK

▶

NEAR >

MOVE

▶

JOYSTICK >

LABEL : TOUR 01

0 1 2 3 4 5 6 7 8 9 (

) A B C D E F G H I J K

L M N O P Q R S T U V W

X Y Z . / , + - = < >

TOUR MENU

< NEAR / RIGHT

▶

TOUR NO >

TOUR NO : 01 DEFINE

LABEL :

TOUR EDIT :

SAVE CLR BACK EXIT

TOUR MENU

< NEAR / RIGHT → DATA SAVE >

TOUR NO : 01 DEFINE

LABEL : TOUR 01

TOUR EDIT :

SAVE CLR BACK EXIT

(4) “Save” above setting Pattern data to the memory.

(5) “CLR” means above setting Pattern data will not be

saved and be cleared.

(6) “BACK” means it goes back to the previous

menu :Motion.

(7) “EXIT” means it goes out of MENU.

SCAN SELECT

< SEL

▶

NEAR / MOVE

&

JOYSTICK >

01 02 03 04 05 06

07 08

SCAN MENU

< NEAR / RIGHT

▶

SCAN NO >

SCAN NO : 01 UNDEFINE

LABEL :

START POS : XXX . X, XXX . X

END POS : XXX . X, ---

SPEED : XX

DWELL : XX

FOCUS : NONE

SAVE CLR BACK EXIT

(1) Select the Scan number

S01 : Defined Scan number / 01 : Undefined Scan number

Move : Select : NEAR

The Scan function means that the camera keeps panning between two programmed pan positions.

It is also adjusts the moving speed(1~63 step). Maximum 8 Scan functions are toured in order.

4. 3. 3 Scan

Scan Quick Operating Guide

Programming : 81~88 + 3sec.

Operating : 81~88 +

SCAN

MAIN MENU

< NEAR / RIGHT

▶

PRESET >

MOTION

▶

DOME

▶

CAMERA

▶

CLEAR

▶

PTZ RESET

BACK EXIT

MOTION MENU

< NEAR / RIGHT

▶

TOUR >

PRESET

▶

TOUR

▶

SCAN

▶

PATTERN

▶

ALARM

▶

AREA

▶

PRIVACY

▶

BACK EXIT

18

Outdoor Speed PTZ Dome Camera System User’s Guide

19

Outdoor Speed PTZ Dome Camera System User’s Guide

SCAN MENU

< NEAR / RIGHT

▶

SCAN NO >

SCAN NO : 01 DEFINE

LABEL : SCAN 01

START POS : XXX . X, XXX . X

END POS : XXX . X, ---

SPEED : XX

DWELL : XX

FOCUS : NONE

SAVE CLR BACK EXIT

SCAN MENU

< NEAR / RIGHT

▶

START POS >

SCAN NO : 01 DEFINE

LABEL : SCAN 01

START POS : 000 . 0 , 000 . 0

END POS : 000 . 0 , ---

SPEED : 60

DWELL : 02

FOCUS : AUTO

SAVE CLR BACK EXIT

SCAN MENU

< NEAR / RIGHT

▶

END POS >

SCAN NO : 01 DEFINE

LABEL : SCAN 01

START POS : 000 . 0 , 000 . 0

END POS : 000 . 0 , ---

SPEED : 60

DWELL : 02

FOCUS : AUTO

SAVE CLR BACK EXIT

STRAT POSITION

< EXIT → FOCUS NEAR >

POSITION : 000.0, 000.0

(3) Define the Start pan position

① Select Start Pos menu

or

NEAR

② Move and set the position ③ Go back

NEAR

(2) Set the Scan Label

Move : Select : or or Delete : or

TELE

JOYSTICK

WIDE

JOYSTICK

(4) Define the End pan position

① Select End Pos menu

or

NEAR

② Move and set the position ③ Go back

NEAR

POSITION : 000.0, 000.0

END POSITION

< EXIT → FOCUS NEAR >

It’s available to set the desired label, displayed on the executing screen of Scan.

After the label is set, push NEAR button to go out.

SCAN LABEL EDIT ( 01 )

< DELETE

▶

WIDE

< STORE

▶

TELE

BACK

▶

NEAR >

MOVE

▶

JOYSTICK >

LABEL : SCAN 01

0 1 2 3 4 5 6 7 8 9 (

) A B C D E F G H I J K

L M N O P Q R S T U V W

X Y Z . / , + - = < >

(8) Save above Scan data setting to the memory.

(9) “CLR” means above setting Scan data will not be

saved and be cleared.

(10) “BACK” means it goes back to the previous

menu :Motion.

(11) “EXIT” means it goes out to MENU

(7) Set the Focus

(5) Set the Scan speed

Increase : or

Decrease : or

TELE

JOYSTICK

WIDE

JOYSTICK

SCAN MENU

< NEAR / RIGHT

▶

MOVE SPEED >

SCAN NO : 01 DEFINE

LABEL : SCAN 01

START POS : 000 . 0 , 000 . 0

END POS : 000 . 0 , ---

SPEED : 60

DWELL : 02

FOCUS : AUTO

SAVE CLR BACK EXIT

SCAN MENU

< NEAR / RIGHT

▶

DWELL >

SCAN NO : 01 DEFINE

LABEL : SCAN 01

START POS : 000 . 0 , 000 . 0

END POS : 000 . 0 , ---

SPEED : 60

DWELL : 02

FOCUS : AUTO

SAVE CLR BACK EXIT

SCAN MENU

< NEAR / RIGHT

▶

DWELL >

SCAN NO : 01 DEFINE

LABEL : SCAN 01

START POS : 000 . 0 , 000 . 0

END POS : 000 . 0 , ---

SPEED : 60

DWELL : 02

FOCUS : AUTO

SAVE CLR BACK EXIT

SCAN MENU

< NEAR / RIGHT

▶

DWELL >

SCAN NO : 01 DEFINE

LABEL : SCAN 01

START POS : 000 . 0 , 000 . 0

END POS : 000 . 0 , ---

SPEED : 60

DWELL : 02

FOCUS : AUTO

SAVE CLR BACK EXIT

It adjusts the moving speed from 1~63 steps.

Focus can be set Auto or Manual.

(6) Set the Dwell Time

Increase : or

Decrease : or

TELE

JOYSTICK

WIDE

JOYSTICK

Dwell time means the time that the camera stay at

the start & end pan positions.

It’s adjustable from 1~60 seconds.

20

Outdoor Speed PTZ Dome Camera System User’s Guide

21

Outdoor Speed PTZ Dome Camera System User’s Guide

PATTERN MENU

< NEAR / RIGHT

▶

PATTERN NO >

PATTERN NO : 01 UNDEFINE

LABEL :

RECORD :

PLAY :

SAVE CLR BACK EXIT

PATTERN SELECT

< SEL

▶

NEAR / MOVE & JOYSTICK >

01 02 03 04

(1) Select the Pattern number

PAT01 : Defined Pattern number / 01 : Undefined Pattern number

Move : Select : NEAR

The Pattern function memorizes User’s random moving path and zoom ratio. Total recording time

limit is 90secs and maximum 4 Pattern functions are toured in order.

4. 3. 4 Pattern

Tour Quick Operating Guide

Programming : 91~94 + 3sec.

Operating : 91~94 +

PATTERN

MAIN MENU

< NEAR / RIGHT

▶

PRESET >

MOTION

▶

DOME

▶

CAMERA

▶

CLEAR

▶

PTZ RESET

BACK EXIT

MOTION MENU

< NEAR / RIGHT

▶

PATTERN >

PRESET

▶

TOUR

▶

SCAN

▶

PATTERN

▶

ALARM

▶

AREA

▶

PRIVACY

▶

BACK EXIT

PATTERN MENU

< NEAR / RIGHT

▶

EDIT LABEL >

PATTERN NO : 01 DEFINE

LABEL :

RECORD

▶

PLAY

▶

SAVE CLR BACK EXIT

PATTERN MENU

< NEAR / RIGHT

▶

RECORD >

PATTERN NO : 01 DEFINE

LABEL :

RECORD ▶

PLAY

▶

SAVE CLR BACK EXIT

PATTERN MENU

< NEAR / RIGHT

▶

PLAY >

PATTERN NO : 01 DEFINE

LABEL :

RECORD

▶

<08SEC>

PLAY

▶

SAVE CLR BACK EXIT

(4) Play back the recorded Pattern data

(3) Record and Save the User’s random Pattern data

① Select the “Record” Menu

or

NEAR

② Move and record the pattern ③ Set & Back

NEAR

000.0, 000.0

EXIT

▶

NEAR 06/60

PATTERN RECORD

(2) Set the Pattern Label

Move : Select : or or Delete : or

TELE

JOYSTICK

WIDE

JOYSTICK

It’s available to set the desired label, displayed on the executing screen of Pattern.

After the label set, push NEAR button to go out.

PATTERN LABEL EDIT ( 01 )

< DELETE

▶

WIDE

< STORE

▶

TELE

BACK

▶

NEAR >

MOVE

▶

JOYSTICK >

LABEL : PATTERN

0 1 2 3 4 5 6 7 8 9 (

) A B C D E F G H I J K

L M N O P Q R S T U V W

X Y Z . / , + - = < >

22

Outdoor Speed PTZ Dome Camera System User’s Guide

23

Outdoor Speed PTZ Dome Camera System User’s Guide

PATTERN MENU

< NEAR / RIGHT

▶

PLAY >

PATTERN NO : 01 DEFINE

LABEL :

RECORD

▶

<08SEC>

PLAY

▶

SAVE CLR BACK EXIT

(5) “Save” above setting Pattern data to the memory.

(6) “CLR” means above setting Pattern data will not be

saved and be cleared.

(7) “BACK” means it goes back to the previous

menu :Motion.

(8) “EXIT” means it goes out of MENU.

AREA MENU

< NEAR / RIGHT

▶

AREA NO > <SEL & MEAR / MOVE & JOYSTICK>

AREA NO : 01 UNDEFINE

LABEL :

START PAN POS.: XXX . X

STOP PAN POS.: XXX . X

SAVE CLR BACK EXIT

AREA MENU

< NEAR / RIGHT

▶

AREA NO >

AREA NO : 01 DEFINE

LABEL :

START PAN POS.: XXX . X

STOP PAN POS.: XXX . X

SAVE CLR BACK EXIT

The Area function means that it displays the Area name between two programmed pan positions.

Maximun 16 Area functions are toured in order.

4. 3. 5 Area

MAIN MENU

< NEAR / RIGHT

▶

PRESET >

MOTION

▶

DOME

▶

CAMERA

▶

CLEAR

▶

PTZ RESET

BACK EXIT

MOTION MENU

< NEAR / RIGHT

▶

PATTERN >

PRESET

▶

TOUR

▶

SCAN

▶

PATTERN

▶

ALARM

▶

AREA

▶

PRIVACY

▶

BACK EXIT

AREA SELECT

01 02 03 04 05

06 07 08 09 10

11 12 13 14 15

16

(1) Select the Area number

AR 01 : Defined Area number / 01 : Undefined Area number

Move : Select : NEAR

(2) Set the Area Label

Move : Select : or or Delete : or

TELE

JOYSTICK

WIDE

JOYSTICK

It’s available to set the desired label, displayed on the executing screen of Area.

After the label set, push NEAR button to go out.

AREA LABEL EDIT ( 01 )

< DELETE

▶

WIDE

< STORE

▶

TELE

BACK

▶

NEAR >

MOVE

▶

JOYSTICK >

LABEL : AREA

0 1 2 3 4 5 6 7 8 9 (

) A B C D E F G H I J K

L M N O P Q R S T U V W

X Y Z . / , + - = < >

24

Outdoor Speed PTZ Dome Camera System User’s Guide

25

Outdoor Speed PTZ Dome Camera System User’s Guide

AREA MENU

< MOVE & NEAR / JOYSTICK >

AREA NO : 01 DEFINE

LABEL :

START PAN POS.: 000 . 0

STOP PAN POS.: 000 . 0

SAVE CLR BACK EXIT

AREA MENU

< MOVE & NEAR / JOYSTICK >

AREA NO : 01 DEFINE

LABEL :

START PAN POS.: 000 . 0

STOP PAN POS.: 000 . 0

SAVE CLR BACK EXIT

AREA MENU

< NEAR / RIGHT

▶

AREA >

AREA NO : 01 DEFINE

LABEL : AREA 01

START POS : 000 . 0 .

STOP POS : 000 . 0 .

SAVE CLR BACK EXIT

AREA START PAN POSITION

< EXIT → FOCUS NEAR >

POSITION : 000.0

AREA STOP PAN POSITION

< EXIT → FOCUS NEAR >

POSITION : 000.0

(3) Define the Start pan position

① Select the “Start Pan Pos” menu

or

NEAR

② Move and set the position ③ Set & Back

NEAR

(4) Define the Stop pan position

① Select the “Start Pan Pos” Menu

or

NEAR

② Move and set the position ③ Set & Back

NEAR

** Only pan position is adjustable, becaue tilt position is fixed when “Start Pan Position” is set.

(5) “Save” above setting Area data to the memory.

(6) “CLR” means above setting Area data will not be

saved and be cleared.

(7) “BACK” means it goes back to the previous

menu :Motion.

(8) “EXIT” means it goes out of MENU

※

Camera will move to clockwise direction only when START setting.

ALARM MENU

< NEAR / RIGHT

&

ALARM NO >

ALARM NO : 01 UNDEFINE

LABEL :

PRESET NO. : XX

SAVE CLR BACK EXIT

ALARM MENU

< NEAR / RIGHT

&

ALARM LABEL >

ALARM NO : 01 DEFINE

LABEL :

PRESET NO. : XX

SAVE CLR BACK EXIT

The Alarm function means that the camera moves to the programmed Preset position by the Alarm trigger.

Maximum 2 Alarm functions are toured in order.

4. 3. 6 Alarm

MAIN MENU

< NEAR / RIGHT

▶

PRESET >

MOTION

▶

DOME

▶

CAMERA

▶

CLEAR

▶

PTZ RESET

BACK EXIT

MOTION MENU

< NEAR / RIGHT

▶

PATTERN >

PRESET

▶

TOUR

▶

SCAN

▶

PATTERN

▶

ALARM

▶

AREA

▶

PRIVACY

▶

BACK EXIT

(1) Select the Alarm number

Alarm 01 : Defined Alarm number / 01 : Undefined Alarm number

Move : Select : NEAR

(2) Set the Alarm Label

Move : Select : or or Delete : or

TELE

JOYSTICK

WIDE

JOYSTICK

It’s available to set the desired label, displayed on the executing screen of Alarm.

After the label is set, push the NEAR button to exit.

ALARM LABEL EDIT ( 01 )

< DELETE

▶

WIDE

< STORE

▶

TELE

BACK

▶

NEAR >

MOVE

▶

JOYSTICK >

LABEL : ALARM 01

0 1 2 3 4 5 6 7 8 9 (

) A B C D E F G H I J K

L M N O P Q R S T U V W

X Y Z . / , + - = < >

ALARM SELECT

< SEL → NEAR / MOVE  JOYSTICK >

01 02

07 08

03 04 05 06

26

Outdoor Speed PTZ Dome Camera System User’s Guide

27

Outdoor Speed PTZ Dome Camera System User’s Guide

ALARM MENU

< NEAR / RIGHT

&

SELECT PRESET >

ALARM NO : 01 DEFINE

LABEL :

PRESET NO. : 01

SAVE CLR BACK EXIT

(3) Define the Preset position with Alarm trigger

① Select the “Preset No”

or

NEAR

② Move and set the position ③ Set & Back

NEAR

(4) “Save” above setting Alarm data to the memory.

(5) “CLR” means above setting Alarm data will not be

saved and be cleared.

(6) “BACK” means it goes back to the previous

menu :Motion.

(7) “EXIT” means it goes out of MENU

PRESET SELECT

001 002 003 004 005 006

007 008 009 010 011 012

013 014 015 016 017 018

019 020 021 022 023 024

025 026 027 028 029 030

031 032 033 034 035 036

037 038 039 040 041 042

043 044 045 046 047 048

049 050 051 052 053 054

<SEL

▶

NEAR /MOVE & JOYSTICK>

ALARM MENU

< NEAR / RIGHT

&

SELECT PRESET >

ALARM NO : 01 DEFINE

LABEL :

PRESET NO. : 01

SAVE CLR BACK EXIT

MAIN MENU

< NEAR / RIGHT

▶

PRESET >

MOTION

▶

DOME

▶

CAMERA

▶

CLEAR

▶

PTZ RESET

BACK EXIT

MOTION MENU

< NEAR / RIGHT

▶

PATTERN >

PRESET

▶

TOUR

▶

SCAN

▶

PATTERN

▶

ALARM

▶

AREA

▶

PRIVACY

▶

BACK EXIT

The Privacy Zone Masking function means that it sets the blocking territories to prevent camera functions

for the privacy of personal reasons. Maximum of 8 Privacy Zone Masking functions are toured in order.

4. 3. 7 Privacy Zone Masking

PRIVACY MENU

< NEAR / RIGHT

▶

PRIVACY NO >

PRIVACY NO : 01 UNDEFINE

POSITION : XXX . X , XXX . X

SAVE CLR BACK EXIT

PRIVACY MENU

< NEAR / RIGHT

▶

PRIVACY NO >

PRIVACY NO : 01 UNDEFINE

POSITION : XXX . X , XXX . X

SAVE CLR BACK EXIT

PRIVACY SELECT

< SEL → NEAR / MOVE

▶

JOYSTICK >

01 02 03 04 05

06 07 08

(1) Select the Privacy Zone number

Privacy 01 : Defined Alarm number / 01 : Undefined Alarm number

Move : Select : NEAR

(2) Set the Privacy Zone Position

Move : Select : or or Delete : or

TELE

JOYSTICK

WIDE

JOYSTICK

It’s available to set the desired position and size of the blocking territories freely.

After the Privacy Zone is set, push the NEAR button to go out.

PRIVACY POSITION

< EXIT

▶

FOCUS NEAR >

POSITION : 000. 0 , 000 .

MASK SIZE : <OPEN / CLOSE >

28

Outdoor Speed PTZ Dome Camera System User’s Guide

29

Outdoor Speed PTZ Dome Camera System User’s Guide

PRIVACY MENU

< NEAR / RIGHT

▶

AREA >

SAVE CLR BACK EXIT

PRIVACY NO : 01 UNDEFINE

POSITION : XXX . X , XXX . X

(3) “Save” above settings of Privacy Zone data to the memory.

(4) “CLR” means above setting of Privacy Zone data will not

be saved and be cleared.

(5) “BACK” means it goes back to the previous

menu :Motion.

(6) “EXIT” means it goes out of MENU.

NEAR

MAIN MENU

< NEAR / RIGHT

▶

PRESET >

MOTION

▶

DOME

▶

CAMERA

▶

CLEAR

▶

PTZ RESET

BACK EXIT

4. 4 Dome Setting

4. 4. 2 Set the Power Up Action

When this function is ON, the camera memorizes the latest action and restores, it from sudden power

failure.

Select : or Set ON : Set OFF :

NEAR

4. 4. 1 Set the Dome camera title

Move : Select : or or Delete : or

TELE

JOYSTICK

WIDE

JOYSTICK

It’s available to set the desired camera title.

After the label is set, push NEAR button to exit.

Pan, Tilt, Zoom motion is adjustable in the “Dome Setting” Menu.

TITLE SET

< DELETE

▶

WIDE

< STORE

▶

TELE

BACK

▶

NEAR >

MOVE

▶

JOYSTICK >

LABEL :

0 1 2 3 4 5 6 7 8 9 (

) A B C D E F G H I J K

L M N O P Q R S T U V W

X Y Z . / , + - = < >

DOME MENU

TITLE

:

TEMP. SET

POWER UP ACTION : ON

PARK ACTION

DISPLAY ON/OFF

DOME SUB MENU

FACTORY SET

SAVE BACK EXIT

< NEAR / RIGHT

▶

TITLE SET >

▶

DOME MENU

TITLE :

TEMP. SET

POWER UP ACTION : ON

PARK ACTION

DISPLAY ON/OFF

DOME SUB MENU

FACTORY SET

SAVE BACK EXIT

< NEAR / RIGHT

▶

TITLE SET >

▶

30

Outdoor Speed PTZ Dome Camera System User’s Guide

31

Outdoor Speed PTZ Dome Camera System User’s Guide

PARK MENU

TIME <MIN> : OFF

FUNCTION : NONE

NUMBER : XX

BACK

PARK MENU

TIME <MIN> : OFF

FUNCTION : NONE

NUMBER : XX

BACK

PARK MENU

TIME <MIN> : OFF

FUNCTION : NONE

NUMBER : XX

BACK EXIT

(1) Set the park Time (OFF, 01~60 min)

(2) Select the function which will be back

after the above set time.

(3) Select the appointed function’s Number

< NEAR / RIGHT

▶

DWELL >

BACK

4. 4. 3 PARK ACTION

or NEAR

(4) “Save” above setting data to the memory.

(5) “CLR” means above setting Pattern data will

not be saved and be cleared.

(6) “BACK” means it goes back to the previous

menu.

(7) “EXIT” means it goes out of the MENU

PARK MENU

TIME <MIN> : OFF

FUNCTION : NONE

NUMBER : XX

This function enables to locate the camera to specific

position automatically if operator doesn’t operate the

controller for a while.

4. 4. 4 Display ON/OFF Set

You can select the OSD ON to shown on the screen or clear by selecting OFF in this function.

Select : or Set ON : Set OFF :

NEAR NEAR

DISPLAY ON/OFF MENU

TITLE :

ZOOM :

PRESET :

TOUR :

AREA :

ALARM :

PATTERN :

PRIVACY :

SCAN :

POSITION :

ACTION :

<V>

<ON

▶

TETLE MOVE

▶

JOY >

<OFF

▶

WIDE BACK

▶

NEAR>

DOME MENU

TITLE :

TEMP. SET

FACTORY SET

POWER UP ACTION : ON

PARK ACTION

▶

DISPLAY ON/OFF

DOME SUB MENU

SAVE BACK EXIT

< NEAR / RIGHT

▶

TITLE SET >

▶

DOME MENU

TITLE :

TEMP SET

FACTORY SET

POWER UP ACTION : ON

PARK ACTION

DISPLAY ON/OFF

DOME SUB MENU

SAVE BACK EXIT

< NEAR / RIGHT

▶

TITLE SET >

▶

When this function is ON, the pan/tilt speed is

inversely adjusted to the zoom ratio.

Select : or Set ON :

Set OFF :

NEAR

Select : or Set ON :

Set OFF :

NEAR

Set tilt angle from 0º to 15º

(OFF~15º)

4. 4. 5 DOME SUB MENU

(1) TILT LIMIT

DOME MENU

TILT LIMIT

SPEED BY ZOOM

AUTO FLIP

RESPONSE TXD

: 10DEG

: ON

: OFF

BACK

< NEAR / RIGHT

▶

SUB MENU >

DOME MENU

TILT LIMIT

SPEED BY ZOOM

AUTO FLIP

RESPONSE TXD

: 10DEG

: ON

: OFF

BACK

< NEAR / RIGHT

▶

SUB MENU >

(2) SPEED BY ZOOM

DOME MENU

TITLE :

TEMP SET

FACTORY SET

POWER UP ACTION : ON

PARK ACTION

DISPLAY ON/OFF

DOME SUB MENU

SAVE BACK EXIT

< NEAR / RIGHT

▶

TITLE SET >

▶

32

Outdoor Speed PTZ Dome Camera System User’s Guide

33

Outdoor Speed PTZ Dome Camera System User’s Guide

Select : or Set ON :

Set OFF :

NEAR

Select : or Set ON :

Set OFF :

NEAR

Select : or Set ON :

Set OFF :

NEAR

Select : or Set ON :

Set OFF :

NEAR

Select : or Set ON :

Set OFF :

NEAR

Select : or Set ON :

Set OFF :

NEAR

Select : or Set ON :

Set OFF :

NEAR

You can observe the moving object without reversing

of the screen, by using this AUTO FLIP function.

ON: If this function is set to ON, camera will be automatically

flipped in tilt 90°

OFF: If this function is set to OFF, tilt movement range is 0~90°

DOME MENU

TILT LIMIT

SPEED BY ZOOM

AUTO FLIP

RESPONSE TXD

: 10DEG

: ON

: OFF

BACK

< NEAR / RIGHT

▶

SUB MENU >

(3) AUTO FLIP

Send the intrinsic protocol value to the Tx line.

(Only for Pelco-D 5.0)

DOME MENU

TILT LIMIT

SPEED BY ZOOM

AUTO FLIP

RESPONSE TXD

: 10DEG

: ON

: OFF

BACK

< NEAR / RIGHT

▶

SUB MENU >

(4) RESPONSE TXD

4. 4. 6 TEMP. SET

DOME MENU

TITLE :

TEMP. SET

POWER UP ACTION : ON

PARK ACTION

DISPLAY ON/OFF

DOME SUB MENU

FACTORY SET

SAVE BACK EXIT

< NEAR / RIGHT

▶

TITLE SET >

▶

< NEAR / RIGHT ON TEMP >

BACK

DOME MENU

HEATER ON TEMP

HEATER ON TIME

HEATER OFF TEMP

FAN ON TEMP

FAN OFF TEMP

: 5 C

: 30 MIN

: 3O C

: 50 C

: 40 C

CURRENT TEMPER 50.06C

< NEAR / RIGHT ON TIME >

BACK

DOME MENU

HEATER ON TEMP

HEATER ON TIME

HEATER OFF TEMP

FAN ON TEMP

FAN OFF TEMP

: 5 C

: 30 MIN

: 3O C

: 50 C

: 40 C

CURRENT TEMPER 50.06C

< NEAR / RIGHT OFF TEMP >

BACK

DOME MENU

HEATER ON TEMP

HEATER ON TIME

HEATER OFF TEMP

FAN ON TEMP

FAN OFF TEMP

: 5 C

: 30 MIN

: 3O C

: 50 C

: 40 C

CURRENT TEMPER 50.06C

< NEAR / RIGHT FAN ON >

BACK

DOME MENU

HEATER ON TEMP

HEATER ON TIME

HEATER OFF TEMP

FAN ON TEMP

FAN OFF TEMP

: 5 C

: 30 MIN

: 3O C

: 50 C

: 40 C

CURRENT TEMPER 50.06C

< NEAR / RIGHT FAN OFF >

BACK

DOME MENU

HEATER ON TEMP

HEATER ON TIME

HEATER OFF TEMP

FAN ON TEMP

FAN OFF TEMP

: 5 C

: 30 MIN

: 3O C

: 50 C

: 40 C

CURRENT TEMPER 50.06C

It shows you the current temperature and you can also set

the value manually. The compulsory Fan & Heater operation

is a useful function to remove humidity.

※ This function support outdoor product only.

Set the operating temperature of the heater.(0~70℃)

Set the operating time of the heater.

- By 10min. (10~60 min.)

Set the temerature of heater OFF. (0~70℃)

Set the operating temperature of the Fan. (0~70℃)

Set the temperature of Fan OFF. (0~70℃)

34

Outdoor Speed PTZ Dome Camera System User’s Guide

35

Outdoor Speed PTZ Dome Camera System User’s Guide

4. 5 Camera Setting

4. 5. 1 CAMERA MENU

CAMERA MENU

- Functions can be set-up using the Camera menu.

In this menu, user can set the zoom, focus, white balance, auto exposure...etc functions.

Decide using of digital zoom function and select zoom speed.

＊ZOOM SPD : 0 ~ 7steps, USER(standard)

＊D-ZOOM : ON / OFF

1) ZOOM MODE

- ZOOM SPD

ZOOM SPD : Select from 0sept to 7 steps,

USER (Standard speed)

Select : or Set ON : Set OFF :

NEAR NEAR

0$,10(18

027,21

'20(

&$0(5$

&/($5

37=5(6(7

(;,7

1($55,*+7୅&$0(5$!

୅

&$0(5$0(18

=22002'(

)2&8602'(

:+,7(%$/

$872(;3

:'502'(

63(&,$/

&$0(5$5(6(7

6$9(%$&.(;,7

୅

1($55,*+7୅=22002'(!

୅

&$0(5$0(18

=22002'(

)2&8602'(

:+,7(%$/

$872(;3

:'502'(

63(&,$/

&$0(5$5(6(7

6$9(%$&.(;,7

୅

1($55,*+7୅=22002'(!

୅

=2200(18

=22063'86(5

'=22021

%$&.

୅

1($55,*+7୅=22063'!

Select : or Set ON :

Set OFF :

NEAR

Restore setting values to the factory default.

All existing setting value will be erased.

4. 4. 7 FACTORY SET

DOME MENU

TITLE :

TEMP. SET

POWER UP ACTION : ON

PARK ACTION

DISPLAY ON/OFF

DOME SUB MENU

FACTORY SET

SAVE BACK EXIT

< NEAR / RIGHT

▶

TITLE SET >

▶

Camera menu subject to change without prior notice to upgrade and quality increase and

we may use slip sheet for the change.

Please check the camera version and the slip sheet if the camera menu and this manual

menu is not matched.

36

Outdoor Speed PTZ Dome Camera System User’s Guide

37

Outdoor Speed PTZ Dome Camera System User’s Guide

- D-ZOOM

Decide using of digital zoom function.

D-ZOOM: ON/ OFF

Select : or Set ON : Set OFF :

NEAR NEAR

=2200(18

=22063'86(5

'=22021

%$&.

୅

1($55,*+7୅'=220!

Select : or Set ON : Set OFF :

NEAR NEAR

Select : or Set ON : Set OFF :

NEAR NEAR

2) FOCUS MODE

- FOCUS SPD

- FOCUS MODE

- NEAR LIMIT

In Focus menu, you can set up the focus speed, focus mode,

near limit and AF mode.

Set the speed for camera focusing.

AUTO: The camera adjusts the focus automatically while

monitoring the screen continuously in the auto mode. In the auto

focusing mode, zoom key operation is not recognized as the input

of the focus key.

Manual: In the manual mode, users can adjust the camera focus

manually.

One Push: It will be focused in about 5 seconds after zooming,

panning, and return to MANUAL mode automatically. This is for

focusing accurately after zooming.

Infinity: infinity focus is the state where a lens forms an image of

an object an infinite distance away. This corresponds to the point

of focus for parallel rays.

Infinity focus is the state where a lens forms an image of

an object an infinite

distance away. This corresponds to the point of focus for

parallel rays.

( Over Infinity~ 1.0CM)

&$0(5$0(18

=22002'(

)2&8602'(

:+,7(%$/

$872(;3

:'502'(

63(&,$/

&$0(5$5(6(7

6$9(%$&.(;,7

୅

1($55,*+7୅=22002'(!

୅

86(5

$872

&0

1250$/

)2&860(18

)2&8663'

)2&8602'(

1($5/,0,7

$)02'(

%$&.

୅

1($55,*+7୅)2&8663'!

86(5

$872

&0

1250$/

)2&860(18

)2&8663'

)2&8602'(

1($5/,0,7

$)02'(

%$&.

୅

1($55,*+7୅)2&8602'(!

86(5

$872

&0

1250$/

)2&860(18

)2&8663'

)2&8602'(

1($5/,0,7

$)02'(

%$&.

୅

1($55,*+7୅1($5/,0,7!

Select : or Set ON : Set OFF :

NEAR NEAR

Select : or Set ON : Set OFF :

NEAR NEAR

Set the AUTO FOCUS MODE position

- AF MODE

86(5

$872

&0

1250$/

)2&860(18

)2&8663'

)2&8602'(

1($5/,0,7

$)02'(

%$&.

୅

1($55,*+7୅$)02'(6(/!

38

Outdoor Speed PTZ Dome Camera System User’s Guide

39

Outdoor Speed PTZ Dome Camera System User’s Guide

3) WHTE BALANCE Set the white balance of camera. 4) AUTO EXPO

- WB MODE

Adjust color leverl (RED, BLUE : 00~ 20)

Standard level : RED -> 10 BLUE->110

- RED, BLUE MODE

White balance setting is a function revising color temperature to

resolve the problem that screen’s colors change by the color

temperature’s difference arrcording to time.

RED GAIN: Adjust red color level from 0~20.

BLUE GAIN: Adjust blue color level from 0~20.

WB MODE: Set the color depend on white balacne.

WB MODE : Select AUTO, INDOOR, OUTDOOR, ONEPUSHAWG

ONEPUSHTRG or MANUAL.

AE setting is a function adjusting shutter speed acoording to

subject’s brightness to get standard amount of exposed light.

AE MODE : Select AUTO,MANUAL,SHUTTER, IRIS or BRIGHT.

EXPOSURE : 00 ~ 20 (Standard 00)

AGC LEVEL : Select ON/OFF to set automatic gain control.

SHUTTER : If you set SHUTTER in AE mode, you can control the level

value

IRIS LEVEL : If you set IRIS in AE mode, you can control the level value

(00~13)

BRIGHT LEVEL : Select brightness level.(0 ~ 20)

DSS LEVEL : Control digital show shutter speed.

&$0(5$0(18

=22002'(

)2&8602'(

:+,7(%$/

$872(;3

:'502'(

63(&,$/

&$0(5$5(6(7

6$9(%$&.(;,7

୅

1($55,*+7୅:%6(77,1*!

୅

$872

;;;

:+,7(%$/$1&(02'(

:%02'(

5('*$,1

%/8(*$,1

%$&.

୅

1($55,*+7୅:%02'(6(/!

0$18$/



:+,7(%$/$1&(02'(

:%02'(

5('*$,1

%/8(*$,1

%$&.

୅

1($55,*+7୅:%02'(6(/!

Select : or Set ON : Set OFF :

NEAR NEAR

Select : or Set ON : Set OFF :

NEAR NEAR

Select : or Set ON : Set OFF :

NEAR NEAR

&$0(5$0(18

=22002'(

)2&8602'(

:+,7(%$/

$872(;3

:'502'(

63(&,$/

&$0(5$5(6(7

6$9(%$&.(;,7

୅

1($55,*+7୅$(6(77,1*!

୅

- AE MODE

- EXPO MODE

Select AUTO,MANUAL,SHUTTER, IRIS or BRIGHT.

Set the exposure.(00 ~20)

Select : or Set ON : Set OFF :

NEAR NEAR

Select : or Set ON : Set OFF :

NEAR NEAR

Select : or Set ON : Set OFF :

NEAR NEAR

Auto level control funtion

: select ON / OFF.

- AGC LEVEL

$872



21

$872

2))

$872(;320(18

$(02'(

(;32685(

$*&/(9(/

6+877(5

,5,6/(9(/

%5,*+7/(9(/

'66/(9(/

%$&.

୅

1($55,*+7୅$(02'(6(/!

$872



21

$872

2))

$872(;320(18

$(02'(

(;32685(

$*&/(9(/

6+877(5

,5,6/(9(/

%5,*+7/(9(/

'66/(9(/

%$&.

୅

1($55,*+7୅(;326(/!

$872



21

$872

2))

$872(;320(18

$(02'(

(;32685(

$*&/(9(/

6+877(5

,5,6/(9(/

%5,*+7/(9(/

'66/(9(/

%$&.

୅

1($55,*+7୅$*&/(9(/!

Page is loading ...

Microdigital MDS-H209 Installation & Operating Manual

Microdigital MDS-H209 Installation & Operating Manual

Other documents