ESAB -31A Motor Replacements Quick start guide

Type
Quick start guide

This manual is also suitable for

IMPORTANT NOTICE
For
MIG-31, -31A Motor Replacements
The enclosed EH-8 motor-gear unit, P/N 999628, is a
new replacement for all units previously used on Mig-
31 and-31A wire feeders. Since the replacement is
slightly larger than the older motors; you may find that,
depending on the vintage of your particular wire feeder,
the existing motor-mounting bracket may require some
modification to accommodate the new replacement.
This modification can be made either by bending-up or
cutting the upper portion of the bracket sheetmetal to
provide the necessary clearance required. Or, if your
feeder is equipped with a bolted-on bracket, you may
prefer to order a new bracket replacement, P/N
2075557. Should you require additional assistance,
please call the Warranty Service Department in Flo-
rence, S.C. at 843-664-4416.
F-14-278
August, 1999
F-14-278 8/99
IMPORTANT NOTICE
For
MIG-31, -31A Motor Replacements
The enclosed EH-8 motor-gear unit, P/N 999628, is a
new replacement for all units previously used on Mig-
31 and-31A wire feeders. Since the replacement is
slightly larger than the older motors; you may find that,
depending on the vintage of your particular wire feeder,
the existing motor-mounting bracket may require some
modification to accommodate the new replacement.
This modification can be made either by bending-up or
cutting the upper portion of the bracket sheetmetal to
provide the necessary clearance required. Or, if your
feeder is equipped with a bolted-on bracket, you may
prefer to order a new bracket replacement, P/N
2075557. Should you require additional assistance,
please call the Warranty Service Department in Flo-
rence, S.C. at 843-664-4416.
F-14-278
August, 1999
F-14-278 8/99
IMPORTANT NOTICE
For
MIG-31, -31A Motor Replacements
The enclosed EH-8 motor-gear unit, P/N 999628, is a
new replacement for all units previously used on Mig-
31 and-31A wire feeders. Since the replacement is
slightly larger than the older motors; you may find that,
depending on the vintage of your particular wire feeder,
the existing motor-mounting bracket may require some
modification to accommodate the new replacement.
This modification can be made either by bending-up or
cutting the upper portion of the bracket sheetmetal to
provide the necessary clearance required. Or, if your
feeder is equipped with a bolted-on bracket, you may
prefer to order a new bracket replacement, P/N
2075557. Should you require additional assistance,
please call the Warranty Service Department in Flo-
rence, S.C. at 843-664-4416.
F-14-278
August, 1999
F-14-278 8/99
IMPORTANT NOTICE
For
MIG-31, -31A Motor Replacements
The enclosed EH-8 motor-gear unit, P/N 999628, is a
new replacement for all units previously used on Mig-
31 and-31A wire feeders. Since the replacement is
slightly larger than the older motors; you may find that,
depending on the vintage of your particular wire feeder,
the existing motor-mounting bracket may require some
modification to accommodate the new replacement.
This modification can be made either by bending-up or
cutting the upper portion of the bracket sheetmetal to
provide the necessary clearance required. Or, if your
feeder is equipped with a bolted-on bracket, you may
prefer to order a new bracket replacement, P/N
2075557. Should you require additional assistance,
please call the Warranty Service Department in Flo-
rence, S.C. at 843-664-4416.
F-14-278
August, 1999
F-14-278 8/99
  • Page 1 1

ESAB -31A Motor Replacements Quick start guide

Type
Quick start guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI