Digi XBee-PRO 868 Adapter Quick start guide

Brand: Digi

Model: XBee-PRO 868 Adapter

Type: Quick start guide

This manual is also suitable for

XBee-PRO 868 Module

XBee-PRO® 868 Development Kit

Getting Started Guide

90002155_A

3/27/2012

©2012DigiInternational,Inc. 2

Allrightsreserved.

Digi,DigiInternational,theDigilogo,theDigiwebsite,aDigiInternationalCompany,XBee,andDigiXBeeare

trademarksorregisteredtrademarksofDigiInternational,Inc.intheUnitedStatesandothercountries

worldwide.Allothertrademarksarethepropertyoftheirrespectiveowners.

Allothertr ademarksmentionedinthisdocumentarethepropertyoftheirrespectiveowners.

Informationinthisdocumentissubjecttochangewithoutnoticeanddoesnotrepresentacommitmentonthe

partofDigiInternational.

Digiprovidesthisdocument“asis,”withoutwarrantyofanykind,eitherexpressedorimplied,including,butnot

limitedto,theimpliedwarrantiesoffitnessormerchantabilityforaparticularpurpose.Digimaymake

improvementsand/orchangesinthismanualorintheproduct(s)and/ortheprogram(s)describedinthismanual

atanytime.

Thisdocumentcouldincludetechnicalinaccuraciesortypographicalerrors.Changesareperiodicallymadetothe

informationherein;thesechangesmaybeincorporatedinneweditionsofthepublication.

©2012DigiInternational,Inc. 3

Table of Contents

Using this Guide............................................................................................................ 4

Conventions used in this Guide.............................................................................. 4

Contact Information................................................................................................. 4

Introduction .................................................................................................................... 5

Goals of the Kit ....................................................................................................... 5

Requirements of the Kit .......................................................................................... 5

5. System Requirements ......................................................................................5

5. Additional Documentation .................................................................................5

Part 1: Set up your XBee-PRO 868 Development Kit .......................................... 6

Identify Kit Components.......................................................................................... 6

Assemble your Development Kit ............................................................................ 7

Part 2: Download and Install X-CTU Software....................................................... 8

Installing USB Drivers............................................................................................. 8

Installing X-CTU Software ...................................................................................... 8

Part 3: Test Communications Link and Establish a Network............................ 9

Perform a Range Test ............................................................................................ 9

©2012DigiInternational,Inc. 4

Using this Guide

Conventions used in this Guide

Thisiconindicatesahint,orconceptthatislearned.

Thisiconindicatesthatagoalofthekithasbeencompleted.

Thisiconindicatesawarningofthepotentialforconfusionordanger.

Contact Information

FormoreinformationaboutyourDigiproducts,orforcustomerserviceandtechnicalsupport,contact

DigiInternational.

ToContactDigiInternational Use

Mail

DigiIn

ternational

WorldHe

adquarters

11001Br

enRoadEast

Minnetonka,MN553

Phone

8:00AM‐5:0

0PM(U.S.MountainTime)

1‐86

6‐765‐9885toll‐freeUSAandCanada

1‐80

1‐765‐9885Worldwide

OnlineSupport http://www.digi.com/support/eservice/login.jsp

Email support.[email protected]

©2012DigiInternational,Inc. 5

Introduction

ThankyouforpurchasinganXBee‐PRO®868DevelopmentKit.Thiskitisdesignedtomakeiteasytoset

upanXBeenetwork,senddatafromoneXBeetoanother,andadjusttheXBeesettings.Beforeyoustart

workingwiththekit,let'scoversomebasics.

Goals of the Kit

Asyougothroughthestepsinthiskit,youwill:

1.SetupyourXBee‐PRO868DevelopmentKit.

2.Downlo

adandinstallX‐CTUconfigurationsoftware.

3.Pe

rformarangetest.

4.Es

tablishanetwork.

5.Con

figuretheradios.

Requirements of the Kit

System Requirements

Toinstallthesoftwarementionedinthisguide,youwillneedaPCrunningMicrosoftWindows

2000,XP,VistaorWindows7.

Additional Documentation

Formoreinformationaboutthesoftware,APIoperations,ATcommandmodes,ortheform

factorpleaserefertotheXBee‐PRO868ProductManualavailableontheDigiSupportwebsite.

Formor

einformationonconfiguringandusingtheX‐CTUutility,pleaserefertotheX‐CTU 

Configuration&Te

stUtilitySoftwareUser’sGuide.

©2012DigiInternational,Inc. 6

Part 1: Set up your XBee-PRO 868

Development Kit

Identify Kit Components

Carefullyunpackandverifythecontentsofyourkit.Yourkitshouldincludethefollowing:

XBee Interface Board (2)

Antenna (1)

XBee Wire

Module (1)

USB Cable (2)

Power Supply (1) Power Supply

Adapters (1)

XBee RPSMA

Module (1)

©2012DigiInternational,Inc. 7

XBee‐PRO®868DevelopmentKitGettingStartedGuide

Assemble your Development Kit

ToassembleyourDevelopmentKit,performthefollowingsteps:

1.Ins

tallthemodulesontheXBeeInterfaceBoards(XBIB)byliningthepinsupwiththeheadersand

pressingthemoduleintoplace.

2.At

tachthedipoleantennastothemodules.

3.Connectthefir

stXBIBtoyourcomputerusingaUSBcable.Thisfirstdevicewillbedesignatedas

yourbaseradio.

4.Connectther

emainingmodulesandinterfaceboards,andsetthemasidefornow.

Youar

enowreadytoruntheX‐CTUsoftwareandtobeginconfiguringyourXBeenetwork.

YouhavejustcompletedGoal#1‐settingupyour

XBee‐PRO868DevelopmentKit.

©2012DigiInternational,Inc. 8

Part 2: Download and Install X-CTU Software

ForproperkitconfigurationandoperationX‐CTUsoftware(version5.15orlater)mustbedownloaded

andinstalled.AcopyofX‐CTUsoftwareandUSBdriverswillneedtobeinstalledoneachcomputerused

inconjunctionwiththisguide.

Installing USB Drivers

TheXBeeUSBinterfaceboardisa"plug‐and‐play"devicethatshouldbedetectedbythePC

automatically.IfyouareusingWindows7orVista,theUSBdriversshouldautomaticallyinstallanda

notificationwillappearinthelowerrightportionofyourscreenindicatingsuccessorfailure.

IftheUSBdriv

ersfailtoinstall,pleasefollowtheUSBdriverinstallationinstructionsfoundhere:

http://www.digi.com/support/kbase/kbaseresultdetl.jsp?id=3214.

Ifyo

uareusingWindows2000orXP,downloadandinstall thedriverasperthefollowingdirections.

Toins

talltheUSBdriver:

1.Downlo

adthedriversetupfileat:

http://ftp1.digi.com/support/driver/FTDI_W

indows_Driver_Setup.exe.

2.Double‐clickonthesetupfi

le.Awindowwillpopupduringinstallationandautomaticallyclose

whentheprocessiscomplete.

Installing X-CTU Software

1.DownloadX‐CTUatwww.digi.com/xctu.

2.Browsetothefo

ldertowhichyousavedtheaboveinstallfile.

3.Double‐clickontheins

tallerfileandfollowtheX‐CTUSetupWizard.

4.Whenas

kedifyouwouldli ketocheckDigi'sweb siteforfirmwareupdates,clickYes.

5.Af

terthefirmwareupdatesarecomplete,clickClose.Updatesmaytakeafewminutes,pleasebe

patient.

6.St

artX‐CTUbydouble‐clickingontheX‐CTUicononyourdesktop,orbyselectingStart>Programs

>Digi>X‐CTU.

TheX‐CT

Usoftwareisnowreadytobeused.

YouhavejustcompletedGoal#2‐downloadingandinstalling

theX‐CTUconfigurationsoftware.

©2012DigiInternational,Inc. 9

Part 3: Test Communications Link and

Establish a Network

Perform a Range Test

Befor erunningarangetest,youwillneedtoestablishaconnectionwiththeX‐CTUsoftware:

1.Double‐clicktheX‐CTUsho

rtcutonyourdesktop.

2.U

nderthePCSettingstab,selecttheserialCOMportassociatedwiththedevelopmentboardsyou

havejustat tachedtoyourcomputer.

3.Verifythatthebaudrateanddatasettingsmatchtheinternalsettingsofthedevices:

• BaudRate:9600

• FlowControl:NONE

• DataBits:8

• Parity:NONE

• StopBits:1

4.OntheModemCon

figurationtab,clickRead.

XBee‐PRO®868DevelopmentKitGettingStartedGuide

5.SelectthePLparameterandchoosetheappropriatepowerlevelfromthedrop‐down

menuPle

asefollowtheseguidelines:

• PL=1(25mW)orlowerisrequiredinItaly.

• PL=3(200mW)orlowerisrequiredwhenusingtheenclosed

USBin

terfaceboardfromDigi,duetocurrentdrawlimitationsof<400mA.

6.ClickWr

itetosavetonon‐volatilememory.

7.Re

movethemodulesfromeachinterfaceboardandswapin terfaceboards.Repeatsteps4‐6to

configurethesecondRFmodulewiththecorrectPLsetting.

XBee‐PRO®868DevelopmentKitGettingStartedGuide

8.ClicktheTest/Querybuttontoverifycommunicationwiththeradio.Apop‐upwi llbedisplayed

showingstatusandsomebasicinformation.

9.Applypow

ertothesecondradiousingapowersupplyinafixedlocation.Thiswillbedesignatedas

yourremoteradio.

Note:YouwillneedtohaveajumperatP8ontheloopbackheaderontheXBIB

fortheremoteradio.

EnsurethattheP8jumperisnotbridgingthetwopinstogetheronthebase

radio.ThiscouldcauseX‐CTUtostallifthejumperispopulatedandrequests

aresenttotheradio.

10.SelecttheRang

eTesttab.

11.(

Optional)Checkthe“RSSI”checkboxtoenableReceivedSignalStrengthIndicator.

XBee‐PRO®868DevelopmentKitGettingStartedGuide

12.ClickStarttobegintherangetest.

XBee‐PRO®868DevelopmentKitGettingStartedGuide

13.MonitorthelinkqualitybyreadingthePercent sectionontheRangeTesttab.Thissection

displaystherunningpercentageofgoodpacketssenttothereceivingradioandloopedbacktothe

base.



Asyo

urdistanceincreasesbeyondthemaximumrangeoftheradios,youwill

startseeinggreaterpacketloss.

14.ClickSt

optoendtherangetest.

XBee‐PRO®868DevelopmentKitGettingStartedGuide

TheAdvancedtaballowsyoutheabilitytoincreasethedatareceivetimeout.whichdefaultsatone

second.Becauseofregulatoryrequirments,youwillneedtoincreasethetimeouttotenseconds

(10,000ms).

Youhavejustcomplet edGoal#3‐performingarangetest.

Digi XBee-PRO 868 Adapter Quick start guide

Brand: Digi

Model: XBee-PRO 868 Adapter

Type: Quick start guide

This manual is also suitable for

XBee-PRO 868 Module

Download PDF

report

Digi XBee-PRO 868 Adapter Quick start guide

This manual is also suitable for

Digi XBee-PRO 868 Adapter Quick start guide

Related papers

Other documents