American Standard TownSquare 2555.050 Installation guide

ENGLISH DEUTSCH

ITALIANO

ESPAÑOL

INSTALLATION GUIDE

FRAN

Ç

AIS

AXIS T95A00 Dome Housing

AXIS T95A10 Dome Housing

Page is loading ...

AXIS T95A00/T95A10 Dome Housing Page 3

ENGLISH

AXIS T95A00/T95A10 Dome Housing

The AXIS T95A00/T95A10 Dome Housing can be used in both indoor and outdoor camera

installations. Follow these instructions to complete the installation of the AXIS T95A00/T95A10

Dome Housing and Axis network camera.

Warning! High voltage - the electrical connection must be made by an authorized electrician.

Please observe relevant national and local regulations for the installation.

• “Package Contents” on page 4

• “Installation” on page 5

• “Technical Specifications” on page 15

Safety Rules

Only qualified technical personnel must install this device.

• Disconnect the power supply before any technical work on the appliance.

• Do not use old or worn out power supply cables.

• Never make changes or connections that are not shown in this handbook; improper use of

the appliance may cause serious hazard and may damage the product.

• Use original spare parts. Non-original spare parts could cause fire, electrical discharge, or

other hazards.

• Before installing the device, check the supplied material to make sure it corresponds with

the order specification.

• Please retain this manual for future reference.

Axis Network Cameras

The AXIS T95A00/T95A10 Dome Housing supports the following camera models:

Camera Model:

Note:

• AXIS 213 PTZ Before you begin, make sure that the AXIS

T95A00/T95A10 Dome Housing package contents, power

supply, and the required cables, tools, and documenta-

tion are available. See “Package Contents” on page 4.

• AXIS 214 PTZ

• AXIS 215 PTZ

• AXIS 231D+/232D+

• AXIS 233D

Page 4 AXIS T95A00/T95A10 Dome Housing

Package Contents

Large box:

(1) AXIS T95A00/T95A10 Dome Housing

Small box:

(2) Domes - transparent and smoked

(1) Fastening ring for dome

(1) Rubber gasket for dome

(4) M3x10mm screws for fastening ring

Plastic bag:

(1) Plate for cable glands

(1) Gasket

(3) M16 cable glands

(1) M12 cable gland

(3) Plastic nuts for M16 cable glands

(1) Plastic nut for M12 cable glands

(3) M3x10mm screws

(3) M3x8mm screws

(4) M4x10mm screws

(3) M3 nuts

(4) M4 nuts

(4) Lock washers

(1) 1/4-inch screw for fixed network camera

(1) 3mm Allen key

Plastic bag:

(1) Desiccant salt bag

Additional parts:

(1) Power connector for AXIS 213 PTZ, AXIS 214 PTZ, and AXIS 215 PTZ

(1) Ethernet connector with 90 degree angle for AXIS 231D+/232D+

AXIS T95A00/T95A10 Dome Housing Page 5

ENGLISH

Tools not included

*The RJ45 connector is attached after the cable has been pulled through the cable gland.

Other required parts

Note:

Not all screws provided are required for all camera installations.

Installation

Prepare the following steps indoors before you proceed to do the installation outdoors. This will

save time at the installation site.

Attach Universal Adaptor plate to camera

1. Remove the top cover of the housing (with four screws) from the housing using the 3mm allen

key.

2. For AXIS T95A00 Dome Housing only - remove the two connectors (with black and blue cables)

attached to the power supply on the Universal Adapter plate.

3. Loosen the three screws holding the Universal Adaptor plate. Slightly rotate and remove the

Universal Adaptor plate.

4. Attach the Universal Adaptor plate to the camera. For details see page 13.

Phillips screw driver

RJ45 crimp tool

*

Adjustable wrench

Bracket see www.axis.com for available brackets and accessories

Power cable AWG20, 100-240 VAC cable (AXIS T95A00 Dome Housing)

AWG22, 24 VAC cable (AXIS T95A10 Dome Housing)

Network cable CAT 5 shielded twisted pair (STP) cable recommended

RJ45 connector

Soft cloth Recommended for protecting the dome while installing the housing

Top cover

Black

cable

Blue

cable

Universal

Adaptor plate

Page 6 AXIS T95A00/T95A10 Dome Housing

Note:

Do not install the camera in the housing at this point. Transport it carefully to the place of

installation first.

Fix the dome to the housing

Place the fastening ring over the dome. Insert the four

10mm M3 screws, so you hold the ring, the dome, and

the gasket together. Fix the dome (transparent or

smoked) on the bottom of the housing.

AXIS 213 PTZ, AXIS 214 PTZ, and AXIS 215 PTZ power connection

1. Connect the (provided) power connector to the 12 VDC output as shown in the picture.

2. Connect the network camera’s power cable.

AXIS T95A00/T95A10 Dome Housing output 12V DC

Camera power connector Housing

black

red

GND

12 V

fastening ring

Housing

Rubber gasket

Dome

Fastening ring

Network camera power connector

12V DC

AXIS T95A00/T95A10 Dome Housing Page 7

ENGLISH

AXIS 231D+/232D+ and AXIS 233D power connection

1. Unplug the connector from the 12 VDC power supply opposite the bracket opening as shown in

the illustration below.

2. Remove the green connector from the cables.

3. Connect the cables to the camera power input as described below:

AXIS 231D+/232D+

• AXIS T95A00 Dome Housing (24V DC)

• AXIS T95A10 Dome Housing (24V AC)

Connect the brown cable to the 24V AC/DC pins on the

AXIS 231D+/232D+ connection module (see illustration).

Note:

The AXIS 231D+/232D+ connection module contains a

rectifier so the cables can be connected either way.

AXIS 233D

• AXIS T95A00 Dome Housing (24V DC)

Connect the brown cable to the GND/DC- and AC/DC+ pins on

the AXIS 233D connector (See illustration).

Be careful to connect (+) and (-) on the correct pins.

• AXIS T95A10 Dome Housing (24V AC)

Connect the brown cable to the AC and AC/DC+ pins on the

AXIS 233D connector (See illustration).

24V

~

+

~

-

12 VDC

power supply

Brown cable

AXIS 231D+/ 232D+

24V AC/DC

Connection module

AXIS 233D

Connector

AC

AC/DC+

GND/DC-

12V out

GND

Line out

GND

Line/Mic in

Page 8 AXIS T95A00/T95A10 Dome Housing

Prepare the cable gland plate

Fix the four cable glands to the cable gland plate and place the cable gland plugs on them. Insert

the four M3 screws through the gasket and plate.

The preparation for the network camera installation is now complete.

Install the bracket

Note:

Make sure all cables are in place and not powered, before you install the bracket. Keep

cables unpowered until the installation is complete.

1. Install the bracket for the AXIS T95A00/T95A10 Dome Housing on a wall and make sure that

the screws and plugs are appropriate for the wall (wood, metal, concrete, or any other), and

suitable for the weight of the housing. To install the bracket in the correct direction, see figure

below.

2. Pull a sufficient length of the cables through the bracket for the housing and camera

(approximately 50 cm).

Note:

Visit the Axis web site at www.axis.com for a comprehensive list of the available brackets

and accessories.

3170

182

150

81

230

14

140

110

77

9

14

AXIS T95A00/T95A10 Dome Housing Page 9

ENGLISH

Mount the housing to the bracket

Notes:

• Ensure that the bracket is securely fastened, and cables are pulled through it before mounting the

camera housing. Ensure that no power is connected to the cables.

• It is recommended that you place a soft, clean cloth (not included) into the dome to ensure it

remains clean until the time when you need to mount the camera.

1. If the top cover of the housing was attached to facilitate transportation, detach it again at this

point.

2. Position the AXIS T95A00/T95A10 Dome Housing against the bracket, making sure to pull the

cable wires (power, Ethernet, and I/O cables if applicable) into the housing, and tighten the two

25mm M5 allen key screws (included with the bracket).

3. Pull the cable wires through the cable glands, and secure the hole in the bracket with the cable

gland plate. Ensure the cable wires are securely fastened in the cable glands.

4. Mount the RJ45 connector to the Ethernet cable, using an RJ45 crimp tool (not provided).

5. Remove the protective cloth (if you have used one) from the dome, and remove traces of dust.

Install the camera in the housing

1. Make sure power disconnected before the camera is installed.

1. Connect the network cable to the Ethernet port in the camera.

2. Connect the power cable to the camera.

3. If applicable, connect the I/O cables to the connectors as described in the installation guide

supplied with the camera.

4. Lower the Universal Adaptor plate with the attached camera into the AXIS T95A00/T95A10

Dome Housing and tighten the screws.

5. Connect the power cable to the housing as described below.

• “For AXIS T95A00 Dome Housing” on page 10

• “For AXIS T95A10 Dome Housing” on page 11

Page 10 AXIS T95A00/T95A10 Dome Housing

For AXIS T95A00 Dome Housing

Attach the power cable (100-240 volt AC) to the housing.

Earth the housing applying the two supplied cables

to the cover and body using M3 screws and the

toothed washer.

100-240V AC

100-240V AC input

Out 24V DC

Overview of complete installation

N

L

GND

Black

Blue

In 100-240V AC

Out 230V AC

Out 12V DC

Brown

cable

AXIS T95A00/T95A10 Dome Housing Page 11

ENGLISH

For AXIS T95A10 Dome Housing

Attach the power cable (24V AC) to the housing.

The safety wire should remain fastened during service.

Place the desiccant bag on the side of the housing

away from cables and electrical components.

Note:

For AXIS 231D+/232D+:

Place the connection module in a suitable position on

top of the bracket away from cables and electrical

components.

Overview of complete installation

Out 24V AC

N 24V AC

L 24V AC

GND

Out 12V DC

Brown

In 24V AC

Red

Desiccant bag

Page 12 AXIS T95A00/T95A10 Dome Housing

Complete the installation

Note:

Make sure that power remains disconnected while you complete the installation.

1. Check that all cables and wires in the housing are properly connected.

2. Follow the instructions in the Installation Guide to install the camera on the network.

3. Once the installation is complete, close the top cover of housing and tighten the screws to lock

the housing using the supplied Allen key.

4. Connect the AC mains power cable.

The installation is now complete.

The Axis network camera installation guide is shipped with the camera or available from the Axis

website at www.axis.com.

If you want to remove the sunshield

Remove the three screws on the side of the sunshield with a Phillips screw driver; remove the screw

on the top center of the cover plate with the 4 mm Allen key.

It is recommended that this is done after the installation.

AXIS T95A00/T95A10 Dome Housing Page 13

ENGLISH

Mount the Universal Adaptor plate to camera

The Universal Adaptor plate consists of five

plates.

Universal adaptor plate when assembled

Fixed plate

Spacer plate

AXIS 233D plate

Moving plate

Spacer plate

A

B

C

D

E

F

G

H

I

L

M

N

A

B

C

D

E

F

G

H

I

L

M

N

11

22

A

B

C

D

E

F

G

H

I

L

M

N

A

B

C

D

E

F

G

H

I

L

M

N

11

22

PF1

PF3

PF2

PM3

PM7-PM8

PM2-PM5

PM8

PM4

PM3

PM7

PM10

PM6

PM10

PM1-PM10

PM7

PM4

PM7

PM4

PM8

PM9-PM11

PM2-PM5

PM9-PM11

PM1-PM10

PM1-PM3

Fixed plate

Spacer plate Spacer plate

AXIS 233D plate

Moving plate

Page 14 AXIS T95A00/T95A10 Dome Housing

For AXIS 233D

1. Adjust the height of the spacer plates to hole F1 on the spacer plate.

2. Place the camera within the four ears of the Universal Adaptor plate

and screw it onto place.

For AXIS 213 PTZ

1. Detach the AXIS 233D plate by removing the three nuts.

2. Adjust the height of the spacer plates to hole B2 on the spacer plate.

3. Place the AXIS 213 PTZ on the Moving plate.

4. Fasten the AXIS 213 PTZ to the two PM 11 holes with two screws.

For AXIS 214 PTZ

1. Detach the AXIS 233D plate by removing the three nuts.

2. Adjust the height of the spacer plates to hole E1 on the spacer plate.

3. Place the AXIS 214 PTZ on the Moving plate.

4. Fasten the AXIS 214 PTZ to the three PM5 holes with three screws.

For AXIS 215 PTZ

1. Detach the AXIS 233D plate by removing the three nuts.

2. Adjust the height of the spacer plates to hole E2 on the spacer plate.

3. Place the AXIS 215 PTZ on the Moving plate.

4. Fasten the AXIS 215 PTZ to the four PM 10 holes with four screws and nuts.

For AXIS 231D+/232D+

1. Detach the AXIS 233D plate by removing the three nuts.

2. Detach the Moving plate, and the Spacer plates.

3. Attach the provided 90° angle Ethernet connector to the network camera.

4. Place the AXIS 231D+/232D+ on the fixed plate.

5. Fasten the network camera, and the camera holder to the three PF2 holes on the fixed plate

with three screws.

6. Attach the network camera to the holder.

AXIS T95A00/T95A10 Dome Housing Page 15

ENGLISH

Technical Specifications

General

Built in die-cast aluminium

Epoxypolyester powder painting

RAL9002 color

Lower dome in polycarbonate Smoked or transparent

Sunshield in ABS for outdoor RAL9002 color

Mechanical

External dimensions with sunshield Ø 351x335mm (13.8x13.2in)

External dimensions without sunshield Ø 314x322mm (12.4x12.7in)

4 cable-glands 3xM16 with Ø cable 3,5-7mm (0.1-0.3in),1xM12

with Ø cable 5-10mm (0.2-0.4in)

Other User’s manual, cable glands and protective gasket

Electrical

Fan assisted heater, Ton 15°C +/-3°C (59°F +/-5°F)

Toff 22°C +/-3°C (71°F +/-5°F)

• AXIS T95A00 Dome Housing:

IN 230Vac, consumption 44W max

• AXIS T95A10 Dome Housing:

IN 24Vac, consumption 24W max

Camera power supply included with internal

adapter

• AXIS T95A00 Dome Housing

• IN 100/240Vac, 50/60Hz, OUT 12Vdc, 3A max

• IN 100/240Vac, 50-60Hz, OUT 24Vdc, 1.5A max

• AXIS T95A10 Dome Housing

• IN 24Vac, 50/60Hz, OUT 12VDC, 2A max

Blower in continuous duty for heater assistance Ton: 15°C +/-3°C (59°F +/-5°F) Toff 22°C +/-3°C (71°F

+/-5°F)

Related products

AXIS T95A61 Wall bracket

AXIS T95A64 Pole adapter

AXIS T95A67 Corner adapter

Environment

Page 16 AXIS T95A00/T95A10 Dome Housing

Indoor / Outdoor Operating temperature: -30°C / +50°C (-4°F /

+122°F)

Compliance to

• CE according to EN61000-6-3, EN 60950, EN50130-4

• IP66 according to EN 60529

Package

Unit weight AXIS T95A00 Dome Housing / AXIS T95A10 Dome

Housing - 3.8kg / 8.3lb

Package weight 4.2kg / 9.3lb

Package dimensions (BxHxL) 38.5x38.5x47cm / 15.1x15.1x18.5in

General

Page is loading ...

Boîtier du dôme AXIS T95A00/T95A10 Page 25

FRANÇAIS

FRAN

Ç

AIS

Pour la Boîtier du dôme AXIS T95A10

Fixez le câble d'alimentation (24 Vca) au boîtier.

Le fil de sécurité doit rester fixé pendant toutes ces opérations.

Placez le sachet anti-condensation sur le côté du boîtier

en prenant soin de l'éloigner des câbles et composants

électriques.

Attention :

For AXIS 231D+/232D+:

Place the connection module in a suitable position on

top of the bracket away from cables and electrical

components.

Vue générale de l'installation

Sortie 24Vca

Sortie 24Vcc

Entrèe 24Vca

Rouge

N 24Vca

L 24Vca

GND

Brun

sachet

anti-condensation

Page is loading ...

Boîtier du dôme AXIS T95A00/T95A10 Page 27

FRANÇAIS

FRAN

Ç

AIS

Fixer la plaque de l'adaptateur universel à la caméra

La plaque de l'adaptateur universel comprend

cinq plaques.

Plaque de l'adaptateur

universel après montage

Plaque rectangulaire

Plaque fixe

Plaque mobile

Plaque AXIS 233D

A

B

C

D

E

F

G

H

I

L

M

N

A

B

C

D

E

F

G

H

I

L

M

N

11

22

A

B

C

D

E

F

G

H

I

L

M

N

A

B

C

D

E

F

G

H

I

L

M

N

11

22

PF1

PF3

PF2

PM3

PM7-PM8

PM2-PM5

PM8

PM4

PM3

PM7

PM10

PM6

PM10

PM1-PM10

PM7

PM4

PM7

PM4

PM8

PM9-PM11

PM2-PM5

PM9-PM11

PM1-PM10

PM1-PM3

Plaque fixe

Plaque rectangulaire Plaque rectangulaire

Plaque mobile

Plaque AXIS 233D

Page is loading ...

AXIS T95A00 / T95A10 Kuppelgehäuse Seite 41

DEUTSCH

Universal-Adapterplatte an der Kamera befestigen

Die Universal-Adapterplatte besteht

aus fünf Platten.

Zusammengebaute

Universal-Adapterplatte

Abstandsplatte

Feststehende

Bewegliche

AXIS 233D-Platte

Platte

A

B

C

D

E

F

G

H

I

L

M

N

A

B

C

D

E

F

G

H

I

L

M

N

11

22

A

B

C

D

E

F

G

H

I

L

M

N

A

B

C

D

E

F

G

H

I

L

M

N

11

22

PF1

PF3

PF2

PM3

PM7-PM8

PM2-PM5

PM8

PM4

PM3

PM7

PM10

PM6

PM10

PM1-PM10

PM7

PM4

PM7

PM4

PM8

PM9-PM11

PM2-PM5

PM9-PM11

PM1-PM10

PM1-PM3

Feststehende Platte

Abstandsplatte Abstandsplatte

Bewegliche Platte

AXIS 233D-Platte

Page is loading ...

AXIS T95A00 / T95A10 Dome Housing Pagina 55

ITALIANO

Montaggio della piastra dell'adattatore universale alla videocamera

La piastra dell'adattatore universale è

costituita da cinque piastre distinte.

Piastra dell'adattatore

universale montata

Piastra distanziatrice

Piastra fissa

Piastra mobile

Piastra AXIS 233D

Piastra

distanziatrice

A

B

C

D

E

F

G

H

I

L

M

N

A

B

C

D

E

F

G

H

I

L

M

N

11

22

A

B

C

D

E

F

G

H

I

L

M

N

A

B

C

D

E

F

G

H

I

L

M

N

11

22

PF1

PF3

PF2

PM3

PM7-PM8

PM2-PM5

PM8

PM4

PM3

PM7

PM10

PM6

PM10

PM1-PM10

PM7

PM4

PM7

PM4

PM8

PM9-PM11

PM2-PM5

PM9-PM11

PM1-PM10

PM1-PM3

Piastra fissa

Piastra distanziatrice Piastra distanziatrice

Piastra mobile

Piastra AXIS 233D

Page is loading ...

Pagina 58 AXIS T95A00 / T95A10 Dome Housing

AXIS T95A67 Adattatore ad angolo

Ambiente

Per esterni/interni Temperatura di funzionamento: -30°C / +50°C (-4°F

/ +122°F)

Conformità

• CE conforme agli standard EN61000-6-3, EN 60950, EN50130-4

• IP66 conforme allo standard EN 60529

Confezione

Peso dell'unità AXIS T95A00 Dome Housing / AXIS T95A10 Dome

Housing - 3,8 kg / 8,3 libre

Peso della confezione 4,2 kg / 9,3 libre

Dimensioni della confezione (BxHxL) 38,5x38,5x47 cm / 15,1x15,1x18,5 pollici

Generale

Page is loading ...

American Standard TownSquare 2555.050 Installation guide

American Standard TownSquare 2555.050 Installation guide

in other languages

Other documents