Seeley Breezair EXV Installation & Operation Manual

Brand: Seeley

Model: Breezair EXV

Type: Installation & Operation Manual

This manual is also suitable for

EXV Series

(English)(EXV)

EXVEvaporativeCooler

INSTALLATION&OPERATIONMANUAL

INDEX

SAFETY

INSTALLATION INSTRUCTIONS

TROUBLE SHOOTING

APPENDIXA

......................................................................................................... 1

Usingthe RemoteControl................................................. 3

Maintenance.................................................................................................. 9

Pre-Assembly Inspection............................................................................... 10

Installation Details.......................................................................................... 11

Water Installation........................................................................................... 12

Electrical Installation...................................................................................... 13

Installation Checklist...................................................................................... 18

................................................................................. 19

- Wiring Diagrams..................................................................... 21

OPERATINGINSTRUCTIONS

ThermostatRange......................................................................................... 2

Usingthe WallControl......................................................... 7

WallControl........................................................................ 13

RemoteControl................................................................... 14

Testingthecooler........................................................................................... 16

SENSOR

TOUCH

EXVEvaporativeCooler

SAFETY INSTRUCTIONS

ImportantSafetyInstructionsand

Warnings

Readthisentiremanualbefore

proceedingtoinstallthecooler.

Failuretoobservethesewarnings

andinstructionswillvoid

manufacturer'swarrantiesandwill

dischargethemanufacturerofall

liability.

ALWAYSdisconnectthecooler

fromthepowersupplybefore

commencingmaintenance

procedures.

AvoidDangerousSituations:

Protectthecoolerfromall

sourcesofignitionbecause

polymersandcoolingpadswill

burn.

WARNING: Thewarningsandsafety

instructionsinthismanualmustbe

followedtoreducetheriskoffire,

electricshockorinjury,andtoprovide

reasonablesafetyandefficiencyin

usingthisEvaporative AirCooler. The

operatorisresponsibleforfollowingthe

warningsandinstructionsinthis

manualandonthecooler.

Duringmaintenanceprocedures,

NEVERuseanakedflameforany

inspectionorcleaningpurposeas

afirecouldbecausedbyaflame

comingintocontactwiththecooler

materials.

NEVERuseawaterhosetosquirtthe

interiorofthecoolerforcleaningas

residualwatercoulddamageelectrical

componentsandcreatetheriskoffire

and/orelectricshocktotheuserafter

re-assembly.

CAUTION

Thisapplianceisnotintendedfor

usebypersons(includingchildren)

withreducedphysical,sensoryor

mentalcapabilities,orlackof

experienceandknowledge,unless

theyhavebeengivensupervisionor

instructionconcerninguseofthe

appliancebyapersonresponsible

fortheirsafety.

Safety

WATERPUMP

Undernocircumstancesare

"PowerClean"styletimedpumps

tobeusedinanyBreezair

evaporativeaircooler.

Failuretofollowthis

instructionwillVOID ALL

WARRANTY andmaycreatesevere

riskofelectricshockandfire!

FAN MOTOR

Failuretofollowthisinstructionwill

VOID ALL WARRANTY andmay

createsevereriskofelectricshock

andfire!

CIRCUITBREAKERPROTECTION

Thewaterpumpissuppliedwiththis

coolerandisfactoryfittedintoits

correctlocation.

Ensurethatitisproperlysecuredand

uprightasintended.

Thereisnoneedtoadjustthewater

flowsincethecoolerisdesignedto

operatewithmaximumcoolingatlow

airvelocities.

Factoryauthorizedpumpsarefitted

withthermaloverloadprotection.

Waterpumpsmayseizeupand

overheat,creatingafirerisk.Pumps

thathavethermaloverloadprotection

aredesignedtoshutoffthepumpif

themotoroverheats.

Seeley"Tornado"pump(partno.

095851)

Useofthese

devicesoranyothernon-approved

devicewillcauseseriousdamageto

thespecialsafetycircuitsofthis

cooler.

Thiscoolerissuppliedwithafan

motormadebythecooler

manufacturer.USEONLY THE

AUTHORIZEDFANMOTOR

SUPPLIED.

Seeley Variable Speed motors:

550W (3/4HP) motorpart # 095118

750W (1HP) motor part # 095125

Thefanmotorisequippedwithinbuilt

overheatingprotectionthatwillreset

automaticallyoncool-downtoasafe

temperature. Thismaytakeupto45

minutes.

Thiscoolerisfittedwithcircuitbreaker

protectionforthefanmotorandpump.

Waterpumpreplacement

Factory Authorizedwaterpump

“PowerClean"StyleTimedPumps

FactoryAuthorized Fan Motor

INSTALLATION,REPAIR AND

OPERATION

Disconnectelectricalpoweratthefuseor

circuitbreakerboxbeforeinstallation

commences. ALWAYSturnOFFtheisolating

switch(disconnect)locatedontheelectronic

moduleinsidethecoolerBEFORE

commencinganymaintenanceprocedures

Keepchildren,bystandersandanimalsat

asafedistance,aminimumof30ft(10m)

awayfromworkingareas.

Dresssafely.Wearnon-skidshoeswhen

workingathighlevelsandroofs.Donot

wearlooseclothingorpersonalaccessories

whileinstallingorservicingtheaircooleras

theymaybecomecaughtinmovingparts.

Keeploosehair,looseclothing,fingers

andallotherpartsofthebodyawayfrom

openingsandmovingparts.

Checkthecoolerforworn,loose,missing,

ordamagedpartsbeforeoperation.

Ifyouworkwithpowertools,wear

protectiveeyewearandgloves.

Takecarewhenliftingorraisingtheair

coolertoitsfinallocation.Usesafe

equipmentandneverattempttoliftthe

cooleralone. Alwayshaveassistance.

Otherwiseyoumightdamagethecooleror

thebuildingorinjureyourself.

GroundFaultCircuitInterrupter(GFCI)

protectionshouldbeprovidedonthecircuit

supplyingthisaircooler.Receptaclesare

availablewithbuilt-inGFCIprotection.

Aircoolersinstalledonroofsmustnot

havethewastewaterdirectedontotheroof

asstainswilloccur.Connectthecoolerdrain

outlettoagutterordrainpipeusinga

suitablehose.

Alwaysusethecorrecttools.

thepackagingplasticonthis

coolercanbeasafetyhazard.Disposeof

carefully.

Neverdrillholesinthepanorwallsofthe

cooler.

Avoiddangeroussituations.Donotuse

thecoolerinthepresenceofflammable

liquidsorgassestoavoidcreatingfireor

explosion. ThisaircoolerisNOT flame

retardant. A firemayresultfromcontactwith

aflameorfromanelectricalshort.

Useofwrongreplacementpartscreates

riskofsevereelectricshockandfirewhich

mayresultinseriouspropertydamage,

personalinjuryordeath.

Useonlythepowersupplyvoltageshown

onthemotor/cabinetnameplate.

Donotinstallorservicetheaircooler

duringrain,highwindorsevereweather

conditions.

!WARNING

Allinstallationandrepairworkmust

conformtolocalelectrical,watersupply

andenvironmentalcodes,rulesand

regulationsandapplicablenational

standards.

Allinstallation,maintenanceand

repairworkmustbedonebya

licensedandqualifiedelectrician

and/oraqualified,experienced

heating,ventilating,airconditioning

technician. Allsuchworkmustbe

effectedwithfactoryauthorized

sparepartsonly.

SEELEY INTERNATIONAL – INSTALLATION&OPERATIONMANUAL

ThermostatRange

WallMounted ThermostatControl

(wallcontrol)

Remote ThermostatControl

(remotecontrol)

AUTO COOL

FAN

SPEED

ECONOMY

REMOTECONTROL

ILL239-D

ILL1140-A

thermostatrange

SENSORTOUCH

EXVEvaporativeCooler

SENSORTOUCH RemoteControl

SEELEY INTERNATIONAL – INSTALLATION&OPERATIONMANUAL

SETTINGTHECLOCK

TURNING THECOOLER

Settheclockontheremotecontrolbeforeproceeding

withanyotherprogramming.

Theclockcanonlybesetwiththeremotecontrol

switchedOFF.Holdthebuttondownforover2

seconds,untilthehourflashes.

Usetheandbuttonstochangethehour.

Tochangeminutes,pressthebuttonagain.

Changetheminutesusingtheand

buttons.

Tolockinthetimesetting,andentertheOFFstate,press

thebutton. Thedisplaywillstopflashing.

Theremotecontrolisswitchedonandoffusingthe

button. Thememorywillstore

Theclockcanbesetto

either12or24hours(seepage6).Iftheclockissetto12

hoursmakesurethatthe AM/PMdisplayedonthescreen

iscorrect. AM/PMwillchangewithadjustmentofthehour.

andusethesettingsfrom

whenthecoolerwaslastused.Oncetheremotecontrolis

on,youcanchoosebetweenMANUAL, AUTOand AUTO

TIMERmodesbypressingthebutton.

WiththeremotecontrolON,pressthebuttonuntil

MANUAL isshowninthetopleftcornerofthedisplay.

ThebuttonisusedtoselectVENT (wherefreshair

isbeingdeliveredwithoutbeingcooled)orCOOL.

MANUAL MODE

OnceeitherCOOL orVENT hasbeenselected,the

remotecontrolwillmaintainaconstantfanspeed.

Thisisindicatedbythebargraphinthecentreofthe

display.

Todecreaseorincreasethefanspeedrequired,

presseithertheorbuttons.

ILL1104-A

AUTOMODE

Theremotecontrolcontainsathermostat.In AUTO

modethecooleriscontrolledautomatically,based

onyourpre-selectedcomfortlevel. Thecoolerwill

adjustthefanspeed,switchbetweenCOOL and

VENT andturnitselfoff.However,thesequence

andregularityatwhichthesesettingschangewill

differwitheachoperationofthecooler.

Astheremotecontrolsensesroomconditions,the

comfortcontrolsettingswillbeinfluencedbyheat

fromdirectsunlightorelectricalappliances.

Likewiseplacingtheremotecontrolincupboards

ordrawersorundercoolingventswillaffectthe

cooler’soperation.

Tosetthe AUTOmodepressthebuttonuntil

AUTOisdisplayed.

Tenlevelsofcomfortareavailablewiththeremote

control.Whilein AUTOmodepressingthe

andbuttonswilladjustthelevelofrequired

comfort. Thedisplaywillshowyourselectionby

indicatingalevelbetween1and10.WARMERor

COOLERwillbedisplayedonthescreenas

settingsarechanged.

AUTO TIMERmodecanbeselectedbyusingthe

button.Oncethe AUTO TIMERmodeis

selectedthecoolerwillonlyoperateduringthe

programmedtimeperiod.

AUTOTIMERMODE

MANUAL VENT

FAN

SPEED

ILL1109-A

AUTO

FAN

SPEED

ILL1105-A

Usingthe RemoteControlSENSORTOUCH

EXVEvaporativeCooler

SENSORTOUCH RemoteControl

Usingthe RemoteControlSENSORTOUCH

AUTO

TIMER

OFF

ILL1115-A

AUTOTIMERMODE

Programmingthetimermustbeperformedbefore AUTO

TIMERcanbeactivated. Thiscanbedonewhileinany

mode,evenwhenitisOFF. Thereare7stepsinvolvedin

settingthe AUTO TIMER.

NOTE: Afterpressingthebuttonthedisplaywill

revertbacktotheprevioussettingifnobuttonsare

pressedwithin4seconds.

Toprogramthetimerusethefollowingsequence:

Beginbypressingthebutton. Thehourdisplayed

willstartflashingandthewordONwillappearonthe

screen. Thenusetheandbuttonsto

changethehourvalue.

Pressthebutton. Theminutesdisplayedwillstart

flashingandthewordONwillappearonthescreen. Then

usetheandbuttonstochangetheminute

setting.

Pressthebutton. Thehourdisplayedwillstart

flashingandOFFwillbedisplayed. Thenusethe

andbuttonstochangethehour.

(1)SettingtheONtimehour

(2)SettingtheONtimeminutes

(3)SettingtheOFFtimehour

(4)SettingtheOFFtimeminutes

(5)Settingthecomfortlevel

(6)SettingECONOMY

(7) Activating AUTOTIMER

Pressthebutton. Theminutesdisplayedwillstart

flashingandthewordOFFwillappear. Thenusethe

and buttonstochangetheminute

setting.

Pressthebuttonandthecomfortlevelnumber

(1to10)displayedwillstartflashing. Thenusethe

andbuttonstochangethissetting.

Toselecteconomypressthebuttonsothatitis

displayedonthescreen.

Nowthatyouhaveprogrammedthesettingsfor AUTO

TIMERtheywillbestoredintheremotecontrol’s

memoryuntilyouchangethem.Pressthebutton

until AUTO TIMERisdisplayedonthescreen. Your

coolerwillnowonlyoperateduringtheprogrammed

timeperiod.

NOTE: Tochangeany AUTO TIMERsettingswhenthe

remotecontrolisswitchedoff,thebuttonneeds

tobepressedandreleasedwithin1second. Tochange

settingswhentheremotecontrolisturnedonpressthe

buttonuntilthedesirednumberisflashing.

AUTO

TIMER

ILL1113-A

AUTO

TIMER

ILL1116-A

AUTO

TIMER ON

ILL1112-A

AUTO

TIMER

OFF

ILL1114-A

ECONOMY MODE

DRAINMODE

PRE-COOL MODE

SelectingtheECONOMY modelimitsthemaximum

availablecoolingorventilationandreducesthepower

usedbyupto20%. TheECONOMY functioncanbeused

ineither AUTOorMANUAL modes. Toselectthismode

pressthebuttonsothatECONOMY appearsonthe

display.

Pressingthebuttonopensthedrainvalveinthe

coolerandemptiesthewaterinthetank. Thiswillleave

thetankcleananddryandturnthecooleroff.

Ifthecoolerhasnotbeenusedfor3daysor3hours,

dependingontheDIP switchsetting-seepage6,the

tankwillautomaticallybedrainedtoensurethesystem

remainsclean.

Yourremotecontrolisdesignedtoallowforthesaturation

ofthecooler’scoolingpadsbeforethefanisswitchedon.

Thisfunction,referredtoasPRE-COOL mode,isenabled

atDIP switchD(refertopage6).Onceitisenabledthe

cooler,whenfirstswitchedon,willoperateasfollows:

(1)......Ifthepanisemptythedrainsystemwillbeclosed.

Thepanwillthenbefilled.

(2)...... Thewaterinletsystemallowswatertofillthepan,

untilthewaterlevelreachesthelowerpinsofthewater

probe. Aftera30seconddelay,thepumpwillturnonand

saturatethecoolingpads.

(3)...... Afterthepumphasbeenrunningfor2minutesthe

fanwillstart.

DuringthisoperationthewordPRE-COOL willbe

displayedontheremotecontrol’sscreen.

NOTE:PRE-COOL modewillnotbeactivatedifVENT

isselectedontheremotecontrolorthecoolerisused

againshortlyafterhavingbeenturnedoff.

TheBreezairremotecontrolisfittedwiththe

WaterManager®featurewhichautomaticallymonitors

thequalityofthewaterinthecooler.

TheWaterManager®drainstheexistingwaterinthe

coolertoallowittobereplacedwithfreshwater,only

whenitisneeded. Therefore,youmaynoticeyour

coolerdrainingwateroccasionally.Howoftenthe

WaterManager®performsthisoperationdependsupon

thequalityofthewatersupplyandtherateof

evaporation.

Inareasofpoorwaterquality,theWaterManager®will

operatemoreoftenasittriestomaintaintheoptimum

waterqualityinthecooler. Thismaximizesthecooling

effectandlifeofthecoolingpads.

Theremotecontrolhasauniquefeatureattachedtothe

WaterManager®thatallowsyoutospecifyeitherhigh

orlowsalinitysettings. Thelowsalinitysettingisusedin

specificcircumstancesonly.Werecommendtalkingwith

yourdealerbeforeadjustingthissetting.

WATERMANAGER

MANUAL

COOL

FAN

SPEED

ECONOMY

ILL1125-A

MANUAL

COOL

FAN

SPEED

ECONOMY

ILL1111-A

DRAINTANK

ILL1107-A

MANUAL

COOL

FAN

SPEED

ECONOMY

ILL1142-A

PRE-COOL

SEELEY INTERNATIONAL – INSTALLATION&OPERATIONMANUAL

Usingthe RemoteControlSENSORTOUCH

SENSORTOUCH RemoteControl

Thehighsalinitysettingisdesignedtooperatethe

cooleratamaximumsafesalinityleveltomaintaina

normalworkinglife.Italsoresultsinaminimum

usageofwater.

NOTE:Highsalinityoutletwatershouldnotbeused

onsaltsensitivegrassorplants.Ithasahighsalt

content.

ThecurrentWaterManager®settingisdisplayedby

holdingdownthebuttonandpressingthe

button. Thesettingcanbechangedbyholdingdown

thebuttonandpressingeithertheor

buttonforHIandLOrespectively.

ThefactorydefaultWaterManager®settingisHI.

Forareasoperatingwithborewater,DIP switchF

shouldbeswitchedtooff(seepage6). Thiswill

disablethesalinitymeasuringcircuitandsimply

drainwaterfromthetankevery65minutesof

operation.

Afterapowerdisruptionisrestored,thecoolerwill

automaticallyrestartwithin10minutes,iftheremote

controlhasremained “ON” duringthepowerfailure.

Ifthebatteriesareinstalledwhenthedisplayis

completelyblank,thedisplaywillremainblankfor5

seconds. After5secondsthedisplaywillshow “Id”

for1second,thendisplaytheclock. Theremote

controlisnowreadytouse.

Theremotecontrolrequires3 AAA batteries. The

useofgoodqualityalkalinebatteriesis

recommended.Undernormalconditionsasetof

batterieswilloperatefor18months.

Whenthebatteriesaregettinglowonpower,

BATTERY LOWisdisplayedonthescreen(the

coolermayalsoswitchoffwhilethedisplayremains

ON). Thisindicatesthatthebatterieshaveonlya

smallamountofliferemaining.

POWERFAILURERECOVERY

BATTERIES

Donotuserechargeablebatteriesastheirvoltage

ratingistoolowfortheremotecontrol.

Tochangethebatteriesremovethecoverfromtheback

oftheremotecontrol.Pullouttheoldbatteriesand

replacethemallwiththenewones.Donotmixnew

batterieswitholdbatteries.

Theremotecontrolhas2minutesofback-uppowerto

retainitsmemorywhilethebatteriesarebeingchanged.

Thereare2rowsofDIP switcheslocatedunderthe

batterycoverontheremotecontrol.

DefinitionofDIP switchpositions(first6inbottomrow

only)areasfollows:

(1)...... Reserved for later use.

(2)...... OFF, 24 hour clock.

ON, 12 hour clock.

(3)...... OFF, 1.0, 3/4HP Motor.

ON, 1/2HP Motor

(4)...... OFF, no pre-cool.

ON, pre-cool.

(5)...... OFF, drains 3 days after power off.

ON, drains 3 hours after power off.

(6)...... OFF,drainsevery65minutesof

operation.

ON,activateswatersalinitycircuit

(WaterManager).

DIP SWITCHES

WARNING:DonotalterDIP switches1to8ontop

rowand7&8onbottomrowasthecoolerwill

ceasetowork.

BOTTOM ROW

MANUAL

COOL

FAN

SPEED

ECONOMY

ILL1110-A

ILL217-H

1 2 3 4 5 6 7 8

OFF

EXAMPLEONLY

AUTO COOL

FAN

SPEED

BATTERYLOW

ILL1106-A

EXVEvaporativeCooler

Usingthe RemoteControlSENSORTOUCH

SENSORTOUCH RemoteControl

STARTING YOURCOOLER

AUTOMATICMODE

MANUAL MODE

Thebuttonturnstheaircooleronandoff.

Therearetwomodesofoperationtochoosefrom,

AutomaticmodeorManualmode.Whentheaircooleris

turnedon,itwillstartinthemodeofoperationitwasin

whenlastturnedoff.Ifyouraircoolerhasbeenofffor

morethan(about)10minutes,whenyoustartit,

“PreparingtoStart” mayflashonthedisplayasshown.

Thisshowsthatthewaterpumpwilloperatetosaturate

thecoolingpadsforafewminutes,beforethefanis

turnedon. Thisensuresthatwhenthefanstarts,only

coolairentersthebuilding.

Thebuttonisusedtoselect Automaticmodeor

Manualmode.When “Auto” isdisplayedthecooleris

under Automaticcontrolandwilloperateaccordingtothe

temperaturesensedatthewallcontrol.

Whentheaircooleristurnedon,itwillreadthe

temperatureandsetthecooleroperationaccordingly.If

thetemperatureincreasesatthewallcontrol,thenthefan

speedwillincrease. Asthetemperaturedecreasesthefan

speedwilldecreaseuntilthecoolerturnsoff.

Pressortooveridetheautomaticcooling

levelsettingandadjustyourroomtemperature.

ToswitchtoManualmode,pressuntil “Man”

appearsinthedisplay.

InManualmodethecoolinglevelcanbemanually

adjusted.

InManualmode,presstochoosebetween

circulatingcoolairoruncooledair.When “Cool” is

displayed,freshcoolairwillcirculateintothebuilding.

When “Vent” isdisplayedasshown,freshuncooledair

willcirculatethroughthebuilding.

Presstoincreasethefanspeedandcirculate

moreair.Presstodecreasethefanspeedand

circulatelessair.Pressoncetochangethespeedby

oneincrement.Holdthebuttondowntochangethe

speedmorequickly.

Youcansettheaircoolersothatitwillturnonaftera

setnumberofhours.

1. Tosetthedelayedstarttime,press

withthecoolerturned . “Startingin” willbe

displayedasshownwiththelastmodeofoperation

(Manualor Automatic).

2. Ifyouwanttheaircoolertoturnonin Automatic

modewiththeprevioussettings,thenpressuntil

“Auto” isdisplayed. Alternatively,ifyouwanttheair

coolertoturnoninManualmode,pressuntil

“Man” isdisplayed,thenpressandthen

ortosettherequiredfanspeed.

3. Tosetthetimeuntilthestart,press.

4. Thenpressortoadjustthetime. The

coolercanstartupto24hoursinadvance.

5. Pressagaintoinitiatethetimedautomatic

start. Thetimedstartwillnotrepeat.

OFF

TIMED AUTOMATICSTART

ILL1122-A

ILL1124-A

AUTOMATICMODEDISPLAY

ILL1122-A

MANUAL COOL DISPLAY

MANUAL VENT DISPLAY

ILL1123-A

ILL1117-A

SEELEY INTERNATIONAL – INSTALLATION&OPERATIONMANUAL

Usingthe WallControlSENSORTOUCH

SENSORTOUCH WallControl

TIMED AUTOMATICSTOP

USINGTHECOOLER

AIRTOOCOLD

AIRNOTCOLDENOUGH

Youcanalsosettheaircoolersothatitwillturnoffaftera

setnumberofhours.

1. To set a delayed stop time, press with the cooler

. ”Stopping in” will display.

2. Press or to adjust the number of hours

before the air cooler will stop. The maximum delay

setting is 24 hours.

3. Press again to begin the timed stop.

Nowthatyouhavereadtheseinstructions,pressthe

buttontoturnyouraircooleron.Iftheaircooler

hasnotoperatedforawhile “PreparingtoStart” willflash

onthedisplay(seepage7). Theprecoolcyclewillbegin

andwilltakeonlyafewminutestocomplete. Afterthis

time,thefanwillstartautomatically,andyoucanenjoy

thecomfortofcoolfreshair!

Withthecoolerrunningin Automaticmode,youmayfind

thatyouaretoocoldorthattheaircoolerisblowingtoo

muchair.Presstoreducetheamountofcooling.

IfyouaretoocoldwiththecoolerrunninginManual

mode,thenpresstoreducethefanspeed. You

canalsocirculatefreshuncooledairbypressing

until “Vent” displays.

Youmayfindthatwiththeaircoolerrunningin Automatic

mode,youarenotcoolenough.Simplypressto

increasecooling.

Ifyouarenotcoolenoughwiththeaircoolerrunningin

Manualmode,thenpresstoincreasethefan

speed.Ensurethatcooledairiscirculatingbypressing

until “Cool” displays.

Youcanexperimentwiththesettingsonyourwall

control.Thisisthebestwaytodecidewhatsuitsyour

needs.

RUNNING

DRAINVALVE

Thisaircoolerissuppliedwithanautomaticdrainthat

performstwoprimaryfunctions:

1. Itopensandclosesautomaticallytocontrolsalt

concentrationsinthetank.

2. Itopenstodrainallwaterandkeepyourtankdry

duringprolonged “off” cycles.

Yourcoolerwillautomaticallychangesomeofthewater

duringoperationwhenthewatersalinitybecomestoo

high. Thisensuresthewaterisalwaysfreshandhelps

maintainyourcooleringoodconditiontoensure

optimumcoolingperformance. Thisiscalled “salinity

sensor” method. Alternativelyandifnecessary,theair

coolercanbesettochangesomewaterafterasettime

ofcoolingoperation. Thefrequencyoftheautomatic

drainfunctionmayhavebeenadjustedbyyourinstaller.

Thisiscalled “timeddrain” method.

Youcanselecteithermethodofwaterreplacementwith

thefollowingsteps.

1. Whenthecooleris ,pressandhold.

2. Whilestillpressing,press.

3. A numberwilldisplaywhichcorrespondstothe

selectedsalinitycontrolmethodasshowninthe

tablebelow.

Pressortochangethedisplayednumber

tothedesiredsalinitycontrolmethod.

4.Press to set your selection.

Whentheaircoolerisnotoperatedfor72hours,the

drainvalvewillopenautomaticallytoemptyallwater

fromthecooler.Ifnecessary,youcanadjustthisdelay

timewiththefollowingsteps.

1. Whenthecoolerisoff,pressandhold.

2. Whilestillpressing,press.

3. A numberwilldisplayindicatingthecurrentwater

draindelaytimeaccordingtothetable.

OFF

ILL1119-A

DisplayNumber

SalinityControlMethod

SalinitySensor

TimedDrain

STANDARD

SENSORTOUCH WallControl

EXVEvaporativeCooler

SENSORTOUCH WallControl

Usingthe WallControlSENSORTOUCH

Pressortoselectyourdesireddelay

time.

4. Presstosetyourselection.

AtanytimewhenthewallcontrolisOFF,youcan

manuallydrainthecoolerbypressingandholding

andfor1second. Thedisplaywillshow “dr” to

confirmtheoperationhasactivated.

Notethatsomeregulatingauthoritiesrequireservicingto

beconductedatspecificintervals.

• Turnoffthepowersupplytotheaircooler.

• Turnoffthewatersupplytotheaircooler.

• Removethepadframesasshown.(Fig.B)

DRAINMODE

WARNING!Ifthesupplycordisdamaged,itmustbe

replacedbyaspecialcordavailablefromthe

manufacturerorit’sserviceagent.

ENDOFSEASONSERVICE

MAINTENANCE

WARNING!Maintenancemustbecarriedoutbyan

authorizedserviceagent.Powertothecoolermust

bedisconnectedbeforepadframesareremovedor

youmayriskpersonalinjury.

HEALTH REGULATIONS

• Turnoffpowerswitchinsidethecooler.

(Fig. A)

• Checkandcleanthelidwaterspreaders

(Fig.C)

• Thoroughlycleanthetankandpumpfilter.

• Gentlywashthepadstoremoveanydust.

• Iffreezingconditionscanoccuratanytime,a

draindownfacilitymustbeprovidedatthelowest

pointofthewatersupplypipe.

• Re-fitthepadframes.

• Turn off the main power supply to the air cooler

• Remove the pad frames as shown.

• Ensure the power switch in the cooler is off.

• Gentlywashthepadstoremoveanydustbuildup

duringthewinterperiod.Ifthepadsareinpoor

condition,replacethem.

• Turn on the power switch inside the cooler.

• Turn on the water and then the main power.

• Re-fit the pad frames and run the cooler.

Toremoveapadframe,insertaflatscrewdrivertipinto

theslotasshownandleveruntildisengagementoccurs.

Takeholdofthepadframeandpullittowardsyouuntil

theinternalsideclipsdisengage.Pivotthepadframe

outwardsandliftup. Takecarenottodamagethepad.

Repeatthesestepsfortheremainingpadframes.(Fig.

PRE SEASON SERVICE

IMPORTANT! Do not damage the pads with high

pressure water spray.

REMOVAL OF PAD FRAMES

Thepadssuppliedhavebeenselectedtogivethe

highestpossiblecoolingperformance.WHEN

REPLACINGPADSDONOTUSE ALTERNATIVES.

Themanufacturerisnotresponsibleforthe

performance,damageto,orsafetyoftheaircooler

whenalternativepadsareused.Usingpoorquality

orincorrectpadsmaycausewatercarry-overthat

mightenterelectricalcomponentscreatingan

electricshockorfirehazard.

DrainDelayTime

DisplayNumber

4hours

1Day

2Days

3Days

4Days

STANDARD

ILL187-E

ILL1383-A

SEELEY INTERNATIONAL – INSTALLATION&OPERATIONMANUAL

Usingthe WallControlSENSORTOUCH

SENSORTOUCH WallControl

PRE-ASSEMBLY INSPECTION

! Checkthatthecorrectcoolerhasbeensupplied. Thecoolershouldhavethefollowingparts:-

(Checkthepartsareinsidethecoolerbyremovingacoolingpadframe.)

EXVEvaporativeCooler

Pre-AssemblyInspection

SLIDE UNIT ON ITS LID

TO AVOID DAMAGE TO

CUTOFF PLATE

ILL939-A

UNPACKING THE COOLER

Cutandremovetheshrinkwrapfrom

aroundthecooler.Using2people,

carefullyliftthecoolerupandaway

fromit’sskid(Fig1).

REMOVINGPADFRAMES

Firstlyremovethecornerclips,which

arelocatedabovethetoplouvreand

thirdlouvrefromthebottomonall

cornerjoins. Theclipswillrequirea

screwdrivertoaidremoval.

Eachframeisclippedintothecooler

andisremovedbyuseofamedium

sizedscrewdriver.Insertthe

screwdriverintothesmallslotsatthe

topoftheframeandleverupwardsuntil

theclipsdisengage. Theframeisnow

freetobeliftedoutofthecoolercabinet

(Fig.2).

Alwayslocatethecoolerwherethereisa

plentifulsupplyofcleanfreshair,andnotin

arecessorclosetothegroundwheretheair

maybedustyorpolluted. Keepthecooler

awayfromheaterflues,exhaustvents

(especiallykitchens)andsourcesof

ignition. Avoiddangeroussituations.

Allowforadequate,SAFEaccessaroundthe

coolerformaintenance,especiallyforpad

cleaning,waterconnections,electrical

connections,drainconnections.

Itismandatorythatwatercannotenterthe

buildingasaresultofpoorsealing(caulking

orflashing)ofthevariouspenetrationsinto

thebuilding(ducts,necks,waterpipes,

electricalconduits).

Thecoolermustbemountedatleast10ft

(preferably15ft)awayfromtheclosest

elementofany TVantenna.Makesurethe

coolerisnotbetweentheantennaandthe

transmissiontowerthatisprovidingthe

televisionsignaltothehome.Ensurethatall

antennacablesareatleast10ftfromthe

cooler.

REPLACINGPADFRAMES

COOLERLOCATION

Ensurethepadframeisthecorrect

wayupbycheckingthatthelouvres

faceupwards.Fittheframeinatthe

bottomalongtheedgeofthepanand

rotateitinatthetop. Takecarenotto

damagetheChillcelastheframe

approachestheplasticwaterspreader

underthetoppanel. Thentwosharp

hitsbyhandshouldlocatetheframe

intoitscorrectlocationunderthetop

panel.Replacethepadframeclipsat

thecorners

Checktheproposedcoolerlocation

first,toensureitisstructurallycapable

ofsupportingtheweightofthecooler.

Polymercoolersarelight-weightbut

theyrequireadequatesupport. The

largestcoolerintheEXVrangeisabout

185lbs(84Kgs).

MOUNTINGTHE AIRCOOLER.

Handlingandinstallingthecooleris

alwaysmucheasierifyouremovethe

padframesfirst.

Newinstallation,roofjacks

Replacement installation, roof jacks

Use24Gorstrongermetalroofjack. The

coolermaythenbeattacheddirectlytothe

jack.

RoofJackrecommendedwallthickness

shouldbe24Gsteelorstronger. The

suppliedroofjackadaptormayberequired

toattachthecoolertotheexistingroofjack.

Forassemblyoftheroofjackadaptor,see

Fig.4.

RAISINGCOOLERTOIT’SFINAL

LOCATION

!Takecarewhenmoving

thecoolerthatnothingisallowed

topenetrateintothedischarge

opening(suchastheendofa

ladder),asdamagemayoccurto

theinternalcoolercomponents.Ifa

ladderisusedasaslideforthe

coolertobepulledontoaroofor

platform,westronglyrecommend

thecoolerbeturnedupside-down

first.Protectthelidfrom

scratching.

HANDLEWITHCARE.DONOT

DROP.

Forliftingorpullingthecooler,always

applytheropesaroundthefullcabinet

orthefanhousingandNEVERtie

themtoanyofthefourcornerposts.

Afterplacingthecoolerontheroof

jackcheckthatwaterspreadersand

otherinternalcomponentsareall

securelyinplace.

WARNING

NOTE! Itisrecommendedthatastrip

offoamorsealantisappliedtothe

upperflangeontheroofjackbefore

securingthecoolertoprovidean

airtightseal.

Ensurethatthetopoftheroofjackis

level,thencheckthelipofthepanfor

levelwhenthecoolerisinpositionon

theroofjack.(Fig.5)

SEELEY INTERNATIONAL – INSTALLATION&OPERATIONMANUAL

InstallationDetails

SECURINGLEGSUPPORTS

Afterlevellingandsecuringthecooler

ontotheroofjackyouarereadytofixthe

fourlegsupports. Thetelescopicleg

supports(withfeetattached)slideupand

downinsidethefourcoolercornerposts.

Byremovingthescrewfromthelower

endofthecornerpostyouenabletheleg

supporttoslidedowntorooflevel.Refer

figs9,10&11fortheprocedurefor

adjustingandsecuringthelegsupports.

Installamanualwatershut-offvalvenearthe

pointofentryofthewatersupplytothe

cooler,inthepermanentwatersupply.In

areassubjecttowinterfreezing,installa

draindownfeature. DONOTFITSHUTOFF

VALVESDIRECTLY ONTOTHEFLOAT

VALVENIPPLEORSOLENOIDVALVE.

WARNING!

Flushforeignmatterfromwatersupplypipe

beforefinalconnectiontotheflexiblehose,

toavoiddamagetothewatersolenoidand

floatvalve.

Thesumpofthepanisdesignedtobe

locatedonthelowsideoftheroof(Fig.8)

Thesupportlegsarenotfullweightbearing

andareonlyintendedforadditionalsupport

incaseofhighwinds,etc.

A permanentwatersupplyisrequiredtobe

connectedtothewaterinletsolenoidvalve

assemblythatissuppliedwiththecooler.

Thefloatvalvethencontrolsthewaterlevel

inthepanautomatically.(Fig.12)

Thepermanentwatersupplyconnection

pointislocatedunderneaththepan,andis

attatchedtotheflexiblehoseandtube

assembly.(Fig14,item “F”)

WATERINSTALLATION

INSTALLINGTHEINLETSOLENOID

VALVE

Fittheinletsolenoidvalveunderthe

panasshown(Fig14).

Insertthesolenoidvalvecable

throughthehole(behindthedrain

valve)andconnecttheplugstothe

solenoidvalve.(Fig.13)Makesure

thecableisfittedtothegroove

underneaththepan. Theelectrical

cableleadsmaybeconnectedtothe

solenoidvalveeitherwayaround.

Usethreadsealtapebetween

solenoidhoseassemblyandbrass

½” BSP to1/4” compression

adaptoror1/2” BSP Nut.

Iffreezingconditionscanoccurat

anytime,adraindownfacilitymust

beprovidedatthelowestpointof

thewatersupplypipe.

A =Solenoid.

B=Nut&Gland

C=Nut

D= Tube Assy

E=Nut

F=Flexiblehoseassy

G=Solenoidcover

H=Solenoidpowerleads .

I=FloatValveNipple½”BSP

J=½”BSP to1/4” CompressionFitting

1/2” BSP Nut&Olive

ILL1228-ESIA2008

(connectstofloatvalve)

(connectsflexiblehosetoSolenoid)

(solenoidtofloatvalve)

(connectsSolenoidtotubeassy)

(InUnit)

Attachthecoolertotheroofjackfrom

insidethecooler(Fig.7),using1¼"long

self-tappingscrews.Useaminimumof

six(6)screws.Inhighwindareasor

whennotusinglegsupportsusea

minimumofeight(8)screws,3perside

and2atthefront.

EXVEvaporativeCooler

InstallationDetails

SENSORTOUCH

INSTALLINGTHEDRAINKIT

Thedrainadaptorallowsthe

attachmentofa¾"drainhosetorun

watertoawastepoint. Attachittothe

drainvalvefittingunderneaththepan

byusingthedrainnut.(Fig.16)

ItisarequirementofSeeley

International-Neverdrainthewater

directlyontotheroof (Thisapplies

toalltypesofcontrol/drain

systems).

Assembledrainvalveasshown(Fig

15).

Makesurethattheo-ringisfitted

beforeplacingthedrainvalveintothe

hole.Screwthenutuptightlybyhand

underneaththecooler.

.Nowconnectthecable(Fig15,

itemB)totheelectronicmodule.

Donotover-

tighten

ELECTRICAL INSTALLATION

Theelectronicmoduleisfactorysealed;

donotattempttoopenit;thereareno

fieldserviceablepartsinside

DONOTTAKERISKS!

The cooler requires a 115V, 60Hz power

supply.

Theelectronicmodulecontainsplug

receptaclesforfanmotor,waterpump,and

otheroptionalfeaturesifused.

Sub-circuitwiringmustberatedatcooler

ratedamperesorhigher,andmustbe

protectedbyasuitablefuseorcircuit

breaker.Sub-circuitcablesaretobedouble

insulatedallthewayintothemainpower

terminationbox.

Whenretro-fittingthecoolerto

anexistinginstallationalwaysturnoffthe

electricalpoweratthesourceofthewiring.

Turnoffandtape

overthecircuitbreakerorremovethefuses

andkeepthemwithyouuntilthejobis

complete.Setcooler,isolatorswitch,wall

switch,motorandpumpto"off".Besureto

tellotheroccupantsofthebuildingwhatyou

aredoing.

Checktobesurethatthe

voltageratingofthecoolermatchesyour

electricalsystemvoltage.

Theelectricalinstallationmustbecarriedout

byalicensedandqualifiedelectrician.

WARNING

INSTALLINGTHEMAINPOWERCABLES

Thepointofentryintothecabinetofthe

coolerisbyknockoutsinthepan.

Sealthegapbetweentheconduitand

knock-outholewithsiliconesealantafter

makingconnectionsandclampingthe

conduitcable.

Ensurethatallelectricalconnections

aretight.Looseconnectionswill

causeoverheatingthatmayleadto

machinedamageorfire.Replaceall

coversoncompletionofthework,

usingonlythescrewssupplied.

Donottamperwithfactorywiring.

Beforeleavingthejob,atrained,

licensedtechnicianmustcheckthat

thecoolerisoperatingcorrectly.

Thiscoolercontainsanelectronic

modulewithmainpowersupply

terminationboxseparatedand

connectedviaacableandplug

assembly.

Themainpowerterminationboxis

providedtofacilitateeasywiring

connections.Cableglandsare

providedfor½"IDconduit.(Fig.19)

RunningtheWallControlCable

PlugtheWallControlcabletopoint

Fig22 “Receiver” ontheelectronic

controller.Runthecabletotheroof

spaceandthentothecontrollervia

themainspowercableentrypointand

plugtotherearoftheWallControl.

OPERATING ADJUSTMENTS

Waterlevel

NEVER ADJUSTTHEWATERLEVEL

WITHTHECOOLERRUNNING

Thewaterlevelinthecooleris

important. Adjustthelevelatthefloat

valveinsidethecooler.Rotatethelarge

plasticfloatCCWorCWtochangethe

level.CWwilllowerthelevel;CCWwill

raisethelevel.(Fig.17)

becausetheresidualwaterinthepads

andpipeswillcausethewatertoover

flowwhenitrunsbackintothepan.

Waterlevelshouldbeabout¼"above

thefloatvalvesupportshelf.(Fig.18)

WallMounted ThermostatControl

(wallcontrol)

WallControl

SENSORTOUCH

65’

InstallationDetails

SEELEY INTERNATIONAL – INSTALLATION&OPERATIONMANUAL

CONNECTOR

ORIENTATION

(sideview)

NOTE:SPLASHCOVERNOTSHOWNFORCLARITY.

Nota:Paramayorclaridadnosemuestralatapaprotectora.

WATERPROBE

Sonda

delagua

MINIMUMSPEED

ADJUST

Ajuste delavelocidad

PUMP

DRAIN

Valvula

dedrenaje

INLET

ntrada

delagua

RECEIVER

Receptor

DIAGNOSTIC

LED’S

LED’

s dediagnóstico

Bomba

ILL1392-A

rientacióndel

conectador

(vistalateral)

MOTORPOWER(AMPS)

Important:Installallthepadframes

excepttheoneonthemotorside.

Bewareofrotatingfan,belt

andpulleyswhilstmakingadjustments

tomotorspeed,pulleyorbelttension

settings.Ensurethecoolerisswitched

OFFviatheelectronicmodule

isolationswitchwhilstworkinginside

thecooler.

Motorloadmustbe

checked thepumprunning.

This

shouldbedonebyatrainedlicensed

electrician.

Ensurethatallintendeddoors,windows

orothermeansofexhaustareopeninthe

building,andthatalloutletgrillesare

openfully.

Setthecoolerrunningatthehighest

speedforabout10minutes,oruntilthe

motorhasreacheditsnormaloperating

temperature(hot!).

Clipyourammeterontothefreecablein

themainterminationbox.(Fig.23)

WARNING:

without

Forconvenience,theratedmotor

current,inamps,isprintedonasmall

labelattachednearthecablefork(in

additiontothenormalmotor

nameplatelabellocatedatthebackof

themotor).

Checkthemeasuredampsagainstthe

.motornameplateamps Ifthemeasured

ampsarelessthanthenameplateampsthe

adjustablemotorpulleysheavemustbe

alteredtoincreasethefanspeed,thereby

deliveringthefullcapabilityofthecoolerto

yourinstallation.

Ifthemeasuredampsaregreaterthanthe

motornameplateampsthefanMUST be

sloweddownbyadjustingthemotorpulley

sheaveintheoppositemanner.

Replaceallcoverswhenadjustmentsare

completedusingthescrewsprovided

Themeasuredampsmust

beequalorcloseto,butnevermorethan

thenameplateamps.(seeheading

"Pulley(Sheave) Adjustment")

Failureto

dothiswillcauseoverheatinginthe

motorandmaycausethemotor’sthermal

protectortotrip.

PULLEY (SHEAVE) ADJUSTMENT

DONOTUSETHEPULLEY ADJUSTMENT

TOSETBELTTENSION.

Themotorpulleyisadjustableinordertoset

themotoramperesatthecorrect

(nameplate)level,andthusprovidethe

ownerwithfullmachinecoolingcapacity.

Theadjustmentismadewiththecooler

switchedOFF.Neverattemptthisprocedure

withthecooleroperating.

Removethedrivebelt.

Toincreasethefanspeed(andthereforethe

motoramps),thetwohalvesofthepulley

mustbeclosertogether,ie:turnthe

adjustablehalfclockwise.(Fig.24)

Todecreasethefanspeed(andtherefore

themotoramps),thetwohalvesofthepulley

mustbefurtherapart,ie:turntheadjustable

halfcounter-clockwise.(Fig.24)

A =FixedSheave

B=GrubScrew

C= AdjustableSheave

D=LockingCap

E=LockingCapScrew

Theouterhalfofthepulleyisona

threadandcanbemovedinoroutby

removingthelockingcapandthen

turningtheouterhalfbyhandinthe

desireddirection.

Whenanadjustmentismade,replace

thelockingcap,aligningthescrew

holewiththenearestholeinthe

adjustablehalf.Lockitintoplacewith

thesecuringscrew.Refitthebelt,

resetthebelttension,thenrunthe

coolerandchecktheamps.Repeat

theprocessuntiltheamplevelisset.

Youcanstartandstopthecoolerfor

thisprocedurebyusingtheisolating

switchinsidethecooler.

Ifitistoo

tighttherewillbeexcessivebeltand

bearingwear.Ifitistooloosethere

willbebeltslip,excessivebeltwear

andlossofcoolerperformance.

Therearetwoadjusterboltswith

lockingnutsattachedtothemotor

mounting.

Thetensionshouldbeadjustedso

thatthedeflectionononesideofthe

beltis5/8"to13/16". Tomakethe

adjustment,loosenthelockingnuts

andscrewtheboltsinoroutas

requiredtochangethebelttension.

Re-tightenthelockingnuts.

Itisimportanttorecheckthemotor

ampsagainafterre-settingthebelt

tension.

Correctbelttensionensuresthebelt

willnotslip.Checkthetemperatureof

thebeltbyhandaftereach

adjustment,byturningoffthecooler

andholdingonesideofthebeltin

yourhand.Ifthebeltiswarmtotouch,

itisslipping!Continuetotightenuntil

itrunscool.(Fig.25)

BELTTENSION

Belttensionisimportant.

EXVEvaporativeCooler

InstallationDetails

Remote ThermostatControl

(remotecontrol)

AUTO COOL

FAN

SPEED

ECONOMY

REMOTECONTROL

ILL239-D

SENSORTOUCH

LOCATINGTHEREMOTECONTROL

INSTALLINGTHERECEIVER

Thefollowingsection

describesinstallationofthereceiver,

whichrequirespositioningofthe

receiverexternaltothecooler,inside

theatticorbelowtheceiling.The

suppliedreceiverleadis16’ (5.0m)

long,sufficienttoreachintotheattic

orbelowtheceiling,fromthecooler

electronicmodule.

Theremotecontrolshouldbeplaced

approximately5feet(1.5meters)

abovethefloor,inthemostusedroom

inthehome. Thiswillgivetheoptimum

temperaturesensingandoperating

positionfortheuser.

• Avoiddirectsunlightexposure.

• Avoidmountingonexternalwalls.

• Avoidmountingtheremotecontrol

nearheatsourcessuchasstoves

andtelevisions.

• Donotlocateinthedirectairflowof

theductoutlets.

• Donotlocateinstrongdraftsorin

deadspotssuchascupboards/

drawers.

Placementiscriticalforcorrect

functioningofthethermostat

(incorporatedintheremotecontrol).

Thefollowingpointsmustbetakeninto

consideration

Note:

RunningtheReceiverCable

Aimtosecurethereceiverawayfrom

theductwork,butasnearaspossibleto

thelocationoftheremotecontrol.

OtherOptionsforMountingReceiver

SignalProblems

FlatRoofInstallation

PlugthereceivercabletopointFig22

“Receiver” ontheelectroniccontroller.Run

thecabletotheatticspaceorbelowthe

ceilingtothereceiverlocationandplugthe6

pinend(withsticker)tothereceiver.(Fig30)

Forinstallationswheretheroofisframedin

steel,positionthereceiverbetweenthe

metaljoistskeepingtheantennaasfaraway

frommetaljoistsaspossibleanddirecting

theantennaperpendicular(rightangle)to

thejoistswillgivethebestresults.

Formostinstallations,mountingthereceiver

totheroofrafterasshown(Fig29)will

providesatisfactoryperformance.

Thestandardinstallationarrangementwill

satisfythemajorityofapplications.

Howeveryoumayfinddifficultcasesas

follows:

Forsignalproblemsinhouseswithametal

roof,positionthereceiverascloseas

possibletothemetalroofwiththeantenna

pointingdirectlyawayfromtheroof(Fig29).

Wheretheinstallationisonabuildingwitha

flatroofandtheatticspaceislessthan4’

(1.2meters)deep,alternativemounting

locationsmayneedtobefoundforthe

receiver.

Forexample,installthereceiverbelowthe

ceilinginthetopofanearbycupboard.

Donotwrapanyexcessreceivercable

aroundthereceiver.Donotextendthe

receivercable.

16’

SENSORTOUCH RemoteControl

ILL665-D

AUTO COOL

FAN

SPEED

ECONOMY

REMOTECONTROL

A =MetalRoofing.

B=WoodorMetalBeam.

C=Receiver(Mountascloseas

possibletothemetalroof).

A = The6pinplug(theendwiththe

"RECEIVER"stickerattached)

connectsintothesocketonthe

undersideofthereceiver.

Important:

Theorientationandpositionofthe

receivermayaffectthereceiver's

performance.Otherfactorsthatmay

alsoinfluenceperformanceare:

(1)..Shieldingfrommetalintheattic

lyingbetweenthereceiverand

RemoteControl. Thismayinclude

Sisalation/sarking(foilsheets),

andductwork.

(2)..Reflectionsfrommetalaroundthe

receiver.

(3)..Interferencefromnearby

transmitters(e.g.mobilephone, AM

radio, Television,RFsecurity

systems).

SETTINGTHE ADDRESSCODE

within4minutesafterturningon

themainpowerattheelectronics

module.

TheBreezairelectronicsmodulewill

automaticallyrecognizetheremote

controlconnection,providedthe

addresscodehasbeencorrectlyset.

Thisissimplyachievedbyfittingthe

batteriesintotheremotecontrol

Thescreenwillstayblankfor

5secondsthendisplay “Id” for1

second. Thecommunicationaddress

codewilltakeafewsecondstoset,

thentheremotecontrolcanbeturned

on.(Fig.31)

Ifcommunicationcannotbeachieved,

thepowertothecoolerwillneedtobe

turnedoff,andthebatteriesneedto

beremovedfromtheremotecontrol.

Waituntilthescreengoescompletely

blank,thenrepeattheabove

procedure.

SEELEY INTERNATIONAL – INSTALLATION&OPERATIONMANUAL

SENSORTOUCH RemoteControl

1.Fixthetopscrew

tothewall,

without

tightening

completely.

2.Fixthesecond

screwthrough

theloweroval

hole,without

tightening

completely.

3.Straightenand

alignthe

mounting

bracket,tighten

screwstohold

thebracketinit’s

correctposition.

LOCATION ANDTESTING

!Important Oneofthemostcriticalparts

oftheinstallationisthelocationofthe

remotecontrolandreceiver.Ifthis

combinationofcomponentsarenotset

up/locatedcorrectly,itcanresultin

chargeableservicecalls.

Afterthecoolerhasbeeninstalled,place

theremotecontrolintheselectedwall

positionandoperatethecooler.

Switchthecoolertohighspeedand

switchonandoff20timesat

approximately3secondintervals.1

missedtransmissionin20isacceptable,

2missedtransmissionsisnot. This

procedureisdonetocheckthatthe

locationyouhavechosenisnotproneto

interferenceorblockstheradio

transmission.Iftheoperationis

intermittent,tryanotherlocation.

COMMISSIONINGUSINGTHE

REMOTECONTROL

Thefollowinginformationallowsquick

diagnosisatstartup-

actsasa

generaldiagnosticindicator,andwill

functionasfollows:

Taketheremotecontroltotheroofand

controltheCoolerfromthere. Thiswill

saveyoualotoftime.

Powerupthecoolerusingtheon/off

switchontheElectronicsModule. Test

motorandpumpoperation.Lookatthe

frontoftheModulewhere2lightemitting

diodes(LEDs)aresituated(Fig.32). The

leftLEDis “tricolour” andcanglowgreen,

redoramber. TherightLEDisredonly.If

theleftLEDisdoubleflashinggreen,

everythingisOK,thisisnormaloperation.

•

indicatesthecontrolisrunningnormally.

Ifitdoesnotglowatall,thenthereis

eithernopowertotheElectronicsModule

(checkisolatingswitch,circuitbreaker,

plugandsocketconnections),orafailure

hasoccurred.

• (remotecontrols

only)indicatesthattheElectronics

Modulehasreceivedacommandatan

incorrectIDaddress.(Seetheremote

control-settingaddresscodesection

above,toreestablishthecode)

indicatesoneormoreof

thefollowingfaults:

The"Tricolour(left)LED"

Greendoubleflashevery2seconds

Amberfor1second

Redflashing•

1RedFlash

2RedFlashes

4RedFlashes

7RedFlashes

indicatesthe

statusoftheWaterManager

measurementcircuitandwillfunctionas

follows:

1Flash

2Flashes

3Flashes

4Flashes

ContinuouslyOn

MOTORLOWSPEEDSETTING

indicates

....FaultCode#1 – CommunicationFailure.

indicates

....FaultCode#2 – FailuretoDetectWaterat

Probes.

indicates

...FaultCode#4 – FailuretoClearProbes

duringdrain.

indicates

....FaultCode#7-IncorrectMainPower

SupplyFrequency.

indicates

....WaterManager isoperatingandthe

measuredsalinityisbelowthesetpoint.

indicates

....WaterManager isoperatingandthe

measuredsalinityisabovethesetpoint.

indicates

....TheSalinityControlMethod=Drainevery

65minutes.

indicates

....IncorrectSalinityControlMethodselected.

indicates:

Theprobesareopencircuit,ormeasured

salinityislessthan20us/cm(thewateris

verypure,iehasverylittlesaltcontent).

EXVcoolerswillfunctionacrossawide

speedrange. Theminimumspeedhasbeen

factoryset,andshouldnotrequire

adjustmentundernormalcircumstances.

However,someadjustmentmaybe

necessarytosuitspecificinstallations.

The"Red(bottom)LED"

Afteryouhavesetthemotoramps

andbelttensioncorrectly,checkthe

speedvariationofthecooler.When

thecontrolischangedfrommaximum

tominimumsettings,thereshouldbe

aneasilyrecognizabledifferencein

fanspeed.

Ifthereisnot,checkthefollowing:

Thatwindowsanddoorsareopen.

Ruleofthumbistohave2timesthe

areaoftheoutletgrilleopenfor

exhaustineachroom.

Iftheaboveiscorrectthenproceedas

follows:

Setthefanspeedtominimum

usingtheremotecontrol,sothatonly

twobarsaredisplayedontheremote

control.

Turntheminimumspeed

adjustmentknob(Fig33)clockwise

oranti-clockwise,untilthebeltis

runningatapproximatelyone

revolutionpersecond(thisequates

toafanspeedofapproximately600

rpm).

EXVEvaporativeCooler

TestingtheCooler

SPEED

ADJUSTMENT

TESTING THE COOLER

Onceyouaresatisfiedthatthecooleris

installedandcommissionedcorrectly,it

isimportanttorunthecoolerand

ensurethateverythingisworkingasit

should.

Tryturningthecooleronandoffwith

theremotecontrolinalloftheroomsin

thehouse. Thiswillmakesurethatthe

receiverislocatedcorrectly.

Checkthatthecoolerrunsquietlyand

withabalanceddistributionofairtoall

outlets.

Makesuretherearenowaterleaks.

Initiateadrainofthepanbypressing

thedrainbuttonontheremote

controlor&button

togetheronWallControl.

Checkthedrainfittingsandpipes,

makingsuretherearenoleaks.

DIP SWITCHES

WARNING:DonotalterDIP

switches1to8ontoprowand7&8

onbottomrowasthecoolerwill

ceasetowork.

There are 2 rows of DIP switches

located under the battery cover on the

remote control.

1 2 3 4 5 6 7 8

OFF

ILL217-H

EXAMPLEONLY

Definition of DIP switch positions (first 6

in bottom row only) are as follows:

(1) Reservedforlateruse.

(2) OFF,24hourclock.

ON,12hourclock.

(3) OFF,1.0,3/4HP Motor.

ON, Not Used

(4) OFF,nopre-cool.

ON,pre-cool.

(5) OFF,drains3daysafter

poweroff.

ON,drains3hoursafter

poweroff.

(6) OFF,drainsevery65minutes

ofoperation.

ON,activateswatersalinity

circuit(WaterManager).

SEELEY INTERNATIONAL – INSTALLATION&OPERATIONMANUAL

TestingtheCooler

REMOTECONTROL DIP SWITCHES

WARNING:DonotalterDIP switches1

to8ontoprowand7&8onbottomrow

asthecoolerwillceasetowork.

Record the dip switch settings for this cooler

below (if applicable)

Definition of DIP switch positions (first 6 in

bottom row only) are as follows:

(1) Reservedforlateruse.

(2) OFF,24hourclock.

ON,12hourclock.

(3) OFF,1.0,3/4HP Motor.

ON,NotUsed

(4) OFF,nopre-cool.

ON,pre-cool.

(5) OFF,drains3daysafterpower

off.

ON,drains3hoursafterpower

off.

(6) OFF,drainsevery65minutesof

operation.

ON,activateswatersalinitycircuit

(WaterManager).

ILL217-H

1 2 3 4 5 6 7 8

OFF

EXAMPLEONLY

Cooler level and secure.

All roof work properly sealed.

Ductwork and air distribution checked and outlets correctly set.

Signed by Installer: …………………………………………………

Dated: ………………………………………………………………

All wiring complete.

Control switch correctly installed.

Motor and pump correctly plugged into sockets.

Drain/overflow fitting correctly installed.

Water level and float adjustment checked.

Pump runs and water evenly distributed to all cooling pads.

All control functions checked.

Owner instructed on correct operating procedure and supplied with

operating instructions.

SERVICEENQUIRIES:

ContactyourlocalDealerorInstallerfor

assistance.

OwnersName:______________________

__________________________________

Telephone:_________________________

Address:___________________________

__________________________________

Dealer:____________________________

__________________________________

Installer:___________________________

__________________________________

DateInstalled:_______________________

ModelNo.:__________________________

SerialNo.:__________________________

Motor Type:_________________________

MotorPower:_________________________

InstallationChecklist

EXVEvaporativeCooler

Page is loading ...

Seeley Breezair EXV Installation & Operation Manual

Brand: Seeley

Model: Breezair EXV

Type: Installation & Operation Manual

This manual is also suitable for

EXV Series

Download PDF

report

Seeley Breezair EXV Installation & Operation Manual

This manual is also suitable for

Seeley Breezair EXV Installation & Operation Manual

Related papers

Other documents