SIP INDUSTRIAL EP2M is a surface-mounted water pump designed for draining rainwater, domestic wastewater, and flooded rooms in emergencies. It can also transfer clean or moderately dirty water without solids. The pump features a powerful motor, a durable construction, and various safety features, including thermal overload protection and an automatic cut-off switch. With its compact design and easy installation, the SIP INDUSTRIAL EP2M is a versatile and reliable solution for a wide range of water pumping needs.
SIP INDUSTRIAL EP2M is a surface-mounted water pump designed for draining rainwater, domestic wastewater, and flooded rooms in emergencies. It can also transfer clean or moderately dirty water without solids. The pump features a powerful motor, a durable construction, and various safety features, including thermal overload protection and an automatic cut-off switch. With its compact design and easy installation, the SIP INDUSTRIAL EP2M is a versatile and reliable solution for a wide range of water pumping needs.
16
Please dispose of packaging for the product in a responsi-
ble manner. It is suitable for recycling. Help to protect
the environment, take the packaging to the local
amenity tip and place into the appropriate recycling bin.
Never dispose of electrical equipment or batteries in with
your domestic waste. If your supplier offers a disposal facili-
ty please use it or alternatively use a recognised re-cycling
agent. This will allow the recycling of raw materials and help
protect the environment.
Ref: 031017
FOR HELP OR ADVICE ON THIS PRODUCT PLEASE CONTACT YOUR DISTRIBUTOR,
OR SIP DIRECTLY ON:
TEL:01509500400
EMAIL: sales@sip-group.com or technical@sip-group.com
www.sip-group.com
1
EP2M
Surface Mounted
Water Pump
Please read and fully understand the instructions in this manual
before operation. Keep this manual safe for future reference
07614
2
15
Declaration of Conformity
We
SIP (Machinery Europe) Ltd
ASM Chartered Accountants
First Floor Block One
Quayside Business Park
Dundalk
County Louth
Republic of Ireland
As the manufacturer's authorised representative within the EC
declare that the
EP2M Water Pump - SIP Part No. 07614
Conforms to the requirements of the following directive(s), as indicated.
Signed:
Mr P. Ippaso - Director - SIP (Industrial Products) Ltd
Date: 19/08/2021.
EU - DECLARATION OF CONFORMITY
2006/42/EC
2014/30/EU
2011/65/EU & (EU)2015/863
Machinery Directive
EMC Directive
RoHS Directive
And the relevant harmonised standard(s), including
EN 60335-1:2012+A11+A13+A1+A14+A2
EN 60335-2-41:2003+A1+A2
EN 62233:2008
EN 55014-1:2017
EN 55014-2:2015
EN IEC 61000-3-2:2019
EN 61000-3-3:2013+A1
EN ISO 12100:2010
Declaration of Conformity
We
SIP (Industrial Products) Ltd
Gelders Hall Road
Shepshed
Loughborough
Leicestershire
LE12 9NH
England
As the manufacturer within the UK, England, Scotland & Wales, declare that the
EP2M Water Pump - SIP Part. No. 07614
Conforms to the requirements of the following directive(s), as indicated.
Supply of machinery (Safety) Regulations 2008
Electromagnetic Compatibility Regulations 2016
The Restriction of the Use of Certain Hazardous Substances in Electrical
and Electronic Equipment Regulations 2012
Signed: …………………………………...
Mr P. Ippaso - Director - SIP (Industrial Products) Ltd
Date: 19/08/2021
UK - DECLARATION OF CONFORMITY
And the relevant harmonised standard(s), including
BS EN 60335-1:2012+A11+A13++A1+A14+A2
BS EN60335-2-41:2003+A1+A2
BS EN 62233:2008
BS EN 55014-1:2017
BS EN 55014-2:1997+A1+A2 BS EN 55014-2:2015
BS EN 61000-3-2:2014
BS EN IEC 61000-3-2:2019 BS EN 61000-3-3:2013
BS EN 61000-3-3:2013+A1
14
PARTS LIST
Ref. No. Description Sip Part No. Ref. No. Description Sip Part No.
1. Stator PW11-00501 20. Cold compacting PW11-00520
2. Cable holder PW11-00502 21. Washer PW11-00521
3. End plate PW11-00503 22. Mains lead PW11-00522
4. Bolt PW11-00504 23. Filling plug PW11-00523
5. Fan PW11-00505 24. O-ring PW11-00524
6. Fan cover PW11-00506 25. Pump casing PW11-00525
7. Bolt PW11-00507 26. Cable holder PW11-00526
8. Dustproof cover PW11-00508 27. Drain plug PW11-00527
9. Screw PW11-00509 28. Washer PW11-00528
10. Cable holder PW11-00510 29. Mechanical seal PW11-00529
11. Terminal board PW11-00511 30. Bolt PW11-00530
12. Capacitor PW11-00512 31. Bolt PW11-00531
13. Insert spring PW11-00513 32. O-ring PW11-00532
14. Screw PW11-00514 33. Support PW11-00533
15. Mains lead clip PW11-00515 34. Bearing PW11-00534
16. O-ring PW11-00516 35. Shaft key PW11-00535
17. Washer PW11-00517 36. Rotor PW11-00536
18. Screw PW11-00518 37. Wave spring PW11-00537
19. Spring washer PW11-00519 N/A. Male tail piece 1” 27821
3
CONTENTS
Page No. Description
4. Safety Symbols Used Throughout this manual
4. Safety Instructions
7. Guarantee
8. Electrical Connection
9. Technical Specifications
10. Getting To Know Your Water Pump
11. Installation / Operating Instructions
12. Maintenance
13. Exploded Drawing
14. Parts List
2 & 15.
UK & EU -
Declaration of conformity
4
When using your water pump, basic safety precautions should always be followed to
reduce the risk of fire, electric shock, personal injury and / or damage to the water
pump.
Read all of these instructions before operating the water pump and save this user
manual for future reference.
SIP recommends that the water pump should not be modified or used for any appli-
cation other than that for which it was designed.
The water pump can be used to drain rain water, domestic waste water and to re-
move water from flooded rooms in emergency conditions.
The pump can be used to transfer clean or moderately dirty water (no solids).
This pumps is designed to be used in the following applications:
Draining of cisterns, rainwater reservoirs, wells, ponds, storm drains, flooded cellars,
boats and yachts etc.
It is only for use with water and not chemicals or other substances that could damage
the internal seals etc.
The pump cannot be used for flammable, corrosive, explosive or dangerous liquids.
It should not be used where aquatic life is present such as in domestic, or commercial
ponds, or similar.
If you are unsure of its relative applications do not hesitate to contact us and we will
be more than happy to advise you.
The water pump is designed to be powered from a 220 - 240V ~ 50Hz supply, which is
reliably connected to the buildings ground (earth) point.
If an extension lead is required to reach the mains supply, ensure the cross-sectional
SAFETY INSTRUCTIONS
Danger / Caution: Indicates risk of personal injury and/or the possibility of
damage.
Warning: Risk of electrical injury or damage!
SAFETY SYMBOLS USED THROUGHOUT THIS MANUAL
IMPORTANT: Please read the following instructions carefully, failure to do
so could lead to serious personal injury and / or damage to the water
pump.
Note: Supplementary information.
13
EXPLODED DRAWING
12
INSTALLATION / OPERATING INSTRUCTIONS….cont
MAINTENANCE
The pump is mainly maintenance free, you may need, from time to time to clear the
impellor of any unwanted waste / debris (particularly if the pump has been in storage
and un-used for a period of time). Always ensure that the mains lead is removed from
the power supply before all maintenance operations.
Remove the pump house retaining screws (see below).
Remove the main pump housing.
Rinse with clean water to remove debris, clean the impellor and the pump
housing with scouring pad (or similar).
Follow these instructions, in reverse to re-fit the pump housing.
Retaining Screws
Pump Housing
Pump Housing
Impeller
5
SAFETY INSTRUCTIONS….cont
area of the wire in the lead is of a sufficient size for the supply of current over the dis-
tance required.
Do not dismantle the water pump - If repairs are required, they should be performed
by a suitably qualified person; Incorrect reassembly may result in a fire hazard and / or
electric shock.
Always disconnect the water pump from the mains supply prior to cleaning or carrying
out any maintenance.
KNOW YOUR WATER PUMP: Read and understand the owner's manual and labels
affixed to the water pump. Learn its applications and limitations, as well as the po-
tential hazards specific to it.
KEEP YOUNG CHILDREN AND UNTRAINED PERSONNEL AWAY FROM THE WORK AREA:
All visitors should be kept at a safe distance from the work area.
STAY ALERT: Always watch what you are doing and use common sense.
DISCONNECT THE WATER PUMP FROM THE MAINS SUPPLY: When not in use.
DO NOT ABUSE THE MAINS LEAD: Never pull the mains lead it to remove the plug
from the mains socket. Keep the mains lead away from heat, oil and sharp edges.
If the mains lead is damaged, it must be replaced by the manufacturer or its ser-
vice agent or a similarly qualified person in order to avoid unwanted hazards.
HAVE YOUR WATER PUMP REPAIRED BY A QUALIFIED PERSON: The water pump is in
accordance with the relevant safety requirements. Repairs should only be carried
out by qualified persons using original spare parts, otherwise this may result in con-
siderable danger to the user and void the warranty.
DANGER! Check that the water pump is in sound condition and good working order;
Take immediate action to repair or replace damaged parts.
USE RECOMMENDED PARTS ONLY - Unapproved parts may be dangerous and will
invalidate the warranty.
WARNING! Only operate on a level and stable surface.
DO NOT move or handle the water pump during operation.
DO NOT leave the water pump unattended for long periods when in use. Switch the
pump off and unplug from the mains supply before leaving the work area.
Ensure that the pump is correctly turned off and drained fully when not in use; Store
in a safe, dry and frost free location out of reach of children.
ALWAYS locate the water pump in an area of good air flow to ensure that the motor
does not overheat during operation.
DO NOT dismantle or tamper with the water pump as this may be dangerous and
will invalidate the warranty.
Use only the electrical power (voltage, current and frequency) specified on the
model plate of the water pump, or in this manual. If in doubt contact the manufac-
turer.
DO NOT insert hands or other objects into the inlet or the outlet of the pump whilst it
is connected to the mains supply.
6
SAFETY INSTRUCTIONS….cont
Ensure the pump is installed so that it cannot move or slip during operation.
Always check the pump regularly, and take it out of service if the water is likely to
freeze.
Never allow the pump to run without water flowing through it.
The pump should not be used where aquatic life is present such as in domestic, or
commercial ponds, or similar.
Never use the water pump to pump anything other than water, it should not be used
to pump flammable, corrosive or other potentially damaging or dangerous liquids.
Never immerse the pump in water.
Allow enough room around the pump whilst it is running to ensure that there is
enough air flow to cool the motor.
Ensure that your hands are dry when dealing with mains electricity.
Always rinse the pump with clean water and fully drain after each use.
Use only a three-prong, UK grounded mains supply socket.
Understand the operating environment; Before each use the operator should assess,
understand and where possible reduce the specific risks and dangers associated
with the operating environment. Bystanders should also be made aware of any risks
associated with the operating environment.
Children under the age of 8 should not operate, or play with the water pump.
Cleaning and user maintenance should not be carried out by children, unless di-
rectly supervised.
The water pump can be used by children aged from 8 years and above and per-
sons with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way, and understand the hazards involved.
Never use flammable or corrosive liquids to clean the water pump.
If a problem with the water pump is experienced, or if the mains lead or plug be-
come damaged, contact your distributor for repair.
If the water pump is used in a place of work all rules and laws etc. relating to the use
of portable electrical appliances should be followed.
Every SIP water pump is carefully tested and packed during its assembly, on receiv-
ing the pump, check that the pump has not been damaged during transportation;
If the pump is damaged, immediately inform your distributor, and, do not put the
pump into operation until the damage has been repaired or the item replaced.
WARNING: Risk of Electric Shock!
CAUTION: The warnings and cautions mentioned in this user manual can not cover all possi-
ble conditions and situations that may occur. It must be understood by the operator that
common sense and caution are factors which cannot be built into this product, but must be
applied.
11
INSTALLATION / OPERATING INSTRUCTIONS
Warning: The water pump should be connected to the mains supply via
an RCD (residual current device) with an operating current ≤30MA to
ensure that the power is cut should any problems occur.
When installing, please ensure your SIP water pump is disconnected from electrical
supply to prevent possible injury to people and / or damage due to un-wanted start
up.
Note: The hose can be fitted directly to the pump if the hose has the cor-
rect male 1” BSP thread, alternatively; follow the instructions below to fit
the hose by means of a hose adaptor.
Fit the 1” inlet and outlet adaptors to the pump (see below).
Fit the inlet and outlet hoses over the adaptors and secure with a relevant pipe
clip where necessary.
Sit the end of the suction hose into the area to be cleared and the outlet hose
to where the water is to be pumped to.
Note: Solid wall / super tough hose should be used instead of lay flat to
ensure the pump will work closer to its capacity.
Prior to use the pump will need to be primed:
Remove the priming port bung (see page 10 & 12).
Pour water through the port until it is full.
The amount of water needed will depend on different factors such as length of
hose etc.
Note: The pump may need to be primed after every time the pump is
stopped (depending on different factors). The use of an NRV (non return
valve) on the suction hose will reduce this issue.
10
GETTING TO KNOW YOUR WATER PUMP
A
B
C
D
E
F
G
H
Ref. Description Ref. Description
A. Pump Mounting Holes E. Pump Specifications
B. Pump Inlet F. Electrical Terminal Box
C. Priming Port G. Fan Cover
D. Pump Outlet H. Mains Lead
7
GUARANTEE
Note: Proof of purchase will be required before any warranty can be hon-
oured.
This SIP water pump is covered by a 12 month parts and labour warranty covering fail-
ure due to manufacturers defects. This does not cover failure due to misuse or operat-
ing the water pump outside the scope of this manual - any claims deemed to be out-
side the scope of the warranty may be subject to charges Including, but not limited to
parts, labour and carriage costs.
This guarantee does not cover consumables such as hose adaptors & fuses etc.
In the unlikely event of warranty claims, contact your distributor as soon as possible.
8
ELECTRICAL CONNECTION
WARNING! It is the responsibility of the owner and the operator to read, understand
and comply with the following:
You must check all electrical products, before each use, to ensure that they are safe.
You must inspect power cables, plugs, sockets and any other connectors for wear or
damage.
You must ensure that the risk of electric shock is minimised by the installation of appro-
priate safety devices; A residual current circuit Breaker (RCCB) should be incorporated
in the main distribution board. A residual current device (RCD) with an operating cur-
rent ≤30mA should be used. It is particularly important to use an RCD with portable
products that are plugged into a supply which is not protected by an RCCB. If in any
doubt consult a qualified electrician.
Connecting to the power supply:
The EP2M surface mounted water pump is supplied with standard 13A UK type plug
fitted. Consult the technical specification table (page 9) for the required rating, if in
doubt contact a qualified electrician. Before using the water pump, inspect the mains
lead and plug to ensure that none are damaged. If any damage is visible have the
water pump inspected / repaired by a suitably qualified person.
The wires for the plug are coloured in the following way:
Yellow / green Earth
Blue Neutral
Brown Live
As the colours of the wires may not correspond with the markings in your plug, pro-
ceed as follows:
The wire which is coloured brown, must be connected to the terminal, which is
marked L or coloured red (or brown).
The wire which is coloured blue, must be connected to the terminal marked with N or
coloured black (or blue).
The wire which is coloured yellow / green should be connected to the terminal which
is coloured the same or marked with this symbol
Always secure the wires in the plug terminal carefully and tightly.
Secure the cable in the cord grip carefully and securely.
9
TECHNICAL SPECIFICATIONS
Warning: Never connect live or neutral wires to the earth terminal of
the plug. Only fit an approved plug with the correct rated fuse. If in
doubt consult a qualified electrician.
Note: Always make sure the mains supply is of the correct voltage and the
correct fuse, type and rating, is used.
Note: If an extension lead is necessary in order to reach the mains supply; The
cross section should be checked so that it is of sufficient size so as to reduce
the chances of voltage drops; Always fully unwind the lead during use.
ELECTRICAL CONNECTION...cont
Warning: The water pump should be connected to the mains supply via
an RCD (residual current device ) with an operating current ≤30mA to
ensure that the power is cut should any problems occur.
Note: The EP2M surface mounted water pump is supplied with standard
13A UK type plug and mains lead fitted. It is intended for sale and use in this
configuration for the UK market only.
Model No. 07614
Model Name EP2M Surface Mounted Water Pump
Input Voltage 220 - 240V ~
Input Frequency 50 Hz
Input Power 550 Watts
Max. Pumping Head 40 Metres
Max. Flow Rate 40 L/Min
Max. Water Temperature 35ºC
Outlet 1” bsp
Mains Lead Length 0.5 Metres
Protection IPX4
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
SIP INDUSTRIAL EP2M is a surface-mounted water pump designed for draining rainwater, domestic wastewater, and flooded rooms in emergencies. It can also transfer clean or moderately dirty water without solids. The pump features a powerful motor, a durable construction, and various safety features, including thermal overload protection and an automatic cut-off switch. With its compact design and easy installation, the SIP INDUSTRIAL EP2M is a versatile and reliable solution for a wide range of water pumping needs.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
SIP INDUSTRIAL 04917 User manual
-
SIP INDUSTRIAL 06817 User manual
-
SIP INDUSTRIAL 036333 User manual
-
SIP INDUSTRIAL 09586 User guide
-
SIP INDUSTRIAL 05647 4-in-1 Air Conditioner User manual
-
SIP INDUSTRIAL 09220 User manual
-
SIP INDUSTRIAL 03683 User manual
-
SIP INDUSTRIAL 01946 User manual
-
SIP INDUSTRIAL 03642 Owner's manual
