Reely 2282651 User manual

Brand: Reely

Model: 2282651

Type: User manual

Reely 2282651 is a 3-CH Helicopter 2.4 GHz RtF that features a built-in gyroscope for stability and maneuverability. It has LED side lights and a headlight for flying in low-light conditions. The coaxial rotors provide increased stability and control, making it suitable for both indoor and outdoor use. The helicopter also has rotor blades contact shut-off for safety and a ready-to-fly design for quick and easy setup.

Operating Instructions

3-CH Helicopter 2.4 GHz RtF

Item No. 2282651 Page 2 - 22

Table of contents

Page

1. Introduction ..........................................................................................................................4

2. Explanation of symbols .......................................................................................................4

3. Intended use ........................................................................................................................5

4. Delivery content ...................................................................................................................5

5. Up-to-date operating instructions ........................................................................................5

6. Features and functions ........................................................................................................5

7. Spare parts ..........................................................................................................................6

8. Safety instructions ...............................................................................................................6

a) General information ......................................................................................................7

9. Battery information and safety .............................................................................................8

a) General information ......................................................................................................8

b) LiPo (Rechargeable) batteries ......................................................................................8

c) AA (rechargeable) batteries ..........................................................................................9

d) Charging the helicopter battery ....................................................................................9

10. Operating elements ...........................................................................................................10

a) Helicopter ...................................................................................................................10

b) Transmitter (remote control) .......................................................................................10

11. Gettingreadyforight .......................................................................................................11

a) Charge the helicopter battery ..................................................................................... 11

b) Insert the transmitter batteries ....................................................................................11

c) Insert the helicopter battery ........................................................................................12

d) Preightcheck ............................................................................................................12

12. Flying the helicopter ..........................................................................................................13

a) Controls ......................................................................................................................13

b) Takingoff ....................................................................................................................15

c) Landing.......................................................................................................................15

d) Crash protection .........................................................................................................16

e) Low helicopter battery ...............................................................................................16

f) Adjust trim ..................................................................................................................16

13. Finishedying ...................................................................................................................17

14. Repairs and maintenance .................................................................................................17

a) Replace propeller blade(s) .........................................................................................17

b) Replace tail blade .......................................................................................................18

c) Replace damaged connection rod ..............................................................................18

15. Care and cleaning .............................................................................................................18

16. Troubleshooting .................................................................................................................19

17. Declaration of Conformity (DOC).......................................................................................20

18. Disposal .............................................................................................................................20

a) Product .......................................................................................................................20

b) (Rechargeable) batteries ............................................................................................20

19. Technical data ...................................................................................................................21

1. Introduction

Dear customer,

Thankyouforpurchasingthisproduct.

Important

Keep these operating instructions for reference and provide them together with the

product to any third party.

This product complies with the statutory national and European requirements.

To maintain this status and to ensure safe operation, you as the user must observe these

operating instructions!

If there are any technical questions, please contact: www.conrad.com/contact

2. Explanation of symbols

The symbol with the exclamation mark in the triangle is used to indicate

important information in these operating instructions. Always read this

information carefully.

The arrow symbol indicates special information and advice on operation.

3. Intended use

Theproductisareadytoyremotecontrolledminihelicopter.

The model is intended for indoor use.

It is suitable for persons aged 8 years or older.

Contact with moisture must be avoided under all circumstances.

For safety and approval purposes, you must not rebuild and/or modify this product. If you use

the product for purposes other than those described above, the product may be damaged. In

addition,improperusecanresultinshortcircuits,res,electricshocksorotherhazards.Read

theinstructionscarefullyandstoretheminasafeplace.Makethisproductavailabletothird

parties only together with its operating instructions.

Allcompanynamesandproductnamesaretrademarksoftheir respective owners.Allrights

reserved.

4. Delivery content

• Helicopter

• Transmitter (remote control)

• 1x Spare tail blade

• 2x Main rotor blades (1x A, 1x B)

• 1x Spare connecting rod

• 1x LiPo Battery

• USB charging cable

• Mini screwdriver

• Safety sheet

• Operating instructions (on CDROM)

5. Up-to-date operating instructions

Download the latest operating instructions at www.conrad.com/downloads

or scan the QR code shown. Follow the instructions on the website.

6. Features and functions

• Built-in gyroscope

• LED side lights and headlight

• Coaxial rotors

• Rotor blades contact shut-off

• Readytoy

7. Spare parts

Visit www.conrad.com and search the Item No. for information about any optional accessories,

spares, or replacement parts.

Only use genuine spare parts.

8. Safety instructions

Read the operating instructions carefully and especially observe the safety

information. If you do not follow the safety instructions and information on

proper handling in this manual, we assume no liability for any resulting personal

injury or damage to property. Such cases will invalidate the warranty/guarantee.

Before use • Choose a suitable location.

• Checkthesurroundingsforpossiblehazardsorobstacles.

• Checkthatpartsareproperlyattachedandnotdamaged.Seesection

“d)Preightcheck”onpage12.

• Checkthetransmitterbatterieshavesufcientchargebeforeying.

• TurnONthetransmitterrst,andthenturnONthemodel.Thiswill

prevent loss of control.

During use • Alwayskeepthetransmitteronwhilethemodelisinoperation.

• Alwayskeepyoureyeonthemodel.

After use • TurnOFFthemodelrst,andthenturnOFFthetransmitter.Thiswill

prevent loss of control.

Caution, safety hazard!

This model has the potential to cause damage to property and/or harm

individuals. Ensure that you are sufciently insured, e.g. by taking out private

liability insurance.

If you already have a policy, check with your insurance company that use of

this model is covered by the policy.

a) General information

• Do not leave packaging material lying around carelessly. This may become

dangerous playing material for children.

• Protect the device from extreme temperatures, direct sunlight, strong jolts, high

humidity,moisture,ammablegases,steamandsolvents.

• Do not place the product under any mechanical stress.

• Ifitisnolongerpossibletooperatetheproductsafely,takeitoutofoperationand

protect it from any accidental use. Safe operation can no longer be guaranteed

if the product:

- is visibly damaged,

- isnolongerworkingproperly,

- has been stored for extended periods in poor ambient conditions or

- has been subjected to any serious transport-related stresses.

• Please handle the product carefully. Jolts, impacts or a fall even from a low height

can damage the product.

• Consult an expert when in doubt about the operation, safety or connection of

the device.

• If you have questions which remain unanswered by these operating instructions,

contact our technical support service or other technical personnel.

9. Battery information and safety

a) General information

• Donot leaveany batteries/rechargeablebatteries lyingaround. There is arisk

of batteries being swallowed by children or pets. If swallowed, consult a doctor

immediately!

• Batteries/rechargeable batteries must never be short-circuited, disassembled or

thrownintore.Thereisadangerofexplosion!

• Batteries/rechargeable batteries must not get damp or wet.

• Always observe the correct polarity (plus/+ and minus/-) when installing/inserting

batteries.

• Leakingordamagedbatteries/rechargeablebatteriescancausechemicalburns

toskin.Wearsuitableprotectivegloveswhenhandlingthem.

• Liquids leaking from batteries/rechargeable batteries are chemically highly

aggressive.Objectsorsurfacesthatcomeintocontactwiththemmaytakesevere

damage.Therefore,keepbatteries/rechargeablebatteriesinasuitablelocation.

b) LiPo (Rechargeable) batteries

• Never damage the rechargeable battery. Damaging the casing of the rechargeable

battery might cause an explosion or a re! Unlike conventional batteries/

rechargeable batteries (e.g. AA or AAA type), the casing of the LiPo rechargeable

batterydoesnotconsistofathinsheetbutratherasensitiveplasticlmonly.

• Never short-circuit the contacts of the rechargeable battery. Do not throw the

batteryortheproductintore.Thereisadangerofreandexplosion!

• Charge the rechargeable battery regularly, even if you do are not using the

product. Due to the rechargeable battery technology being used, you do not need

todischargetherechargeablebatteryrst.

• Never charge the rechargeable battery of the product unattended.

• When charging, place the product on a surface that is not heat-sensitive. It is

normal that a certain amount of heat is generated during charging.

c) AA (rechargeable) batteries

• (Rechargeable) batteries should be removed from the device if it is not used for a

longperiodoftimetoavoiddamagethroughleaking.

• All (rechargeable) batteries should be replaced at the same time. Mixing old and

new (rechargeable) batteries in the device can lead to (rechargeable) battery

leakageanddevicedamage.

• (Rechargeable) batteries must not be dismantled, short-circuited or thrown into

re.Neverrechargenon-rechargeablebatteries.Thereisariskofexplosion!

d) Charging the helicopter battery

• (If provided) only use the provided charger to charge the battery.

• Always remove and completely disconnect the battery from the model before

charging.

• Never leave the battery unattended while charging.

• Never cover the charger and the battery when charging is in progress.

• Disconnect the battery from the charger when the battery is fully charged.

• The charger and the rechargeable battery must not get damp or wet. This may

resultinafatalelectricshockorcauseareorexplosion!

• Do not expose the charger or battery to extremely high/low temperatures or direct

sunlight.

• Never use an excessive charging current. Observe the manufacturer’s

specicationsfortheideal/maximumchargingcurrent.

• Keepasufcientdistancebetweenthechargerandthebatterywhilecharging.

• Do not wear any metal or conductive materials, such as jewellery (necklaces,

bracelets,rings, etc.)while youare workingwith thecharger orbattery.Short-

circuit poses a danger of burns and explosion.

• Whencharging,placethebatteryonaheat-insensitivesurface.Itisnormalthata

certain amount of heat is generated during charging.

10. Operating elements

a) Helicopter

1 Blade grip-tension screw

2 Toprotorblade“A”

3 Blade grip-tension screw

4 Bottomrotorblade“B”

5 Headlight

6 Battery cage

7 Landing gear

8 Connecting rod

9 Side lights

10 Batterysocket

11 Battery plug

12 Tail blade

b) Transmitter (remote control)

1 2 3

4 5 6 7 8

1 Throttle lever

2 ON/OFF switch

3 Direction/rotate lever

4 Trim: Left

5 LED status indicator

6 Headlight ON/OFF

7 Trim: Right

8 Battery compartment (rear)

11. Getting ready for ight

a) Charge the helicopter battery

Important

• Onlyusetheincludedchargertochargethebatterypack.Disconnectthebatteryand

remove it from the helicopter before charging.

• USB power source:Beforeconnecting,makesurethattheUSBpowersourcecan

deliversufcientcurrent,otherwiseyoumaydamagethesource.DonotuseaUSB

portof acomputer,keyboard orUSB hubwithout apower adapteras thecurrent

suppliedbytheseportsisinsufcient.

Connect one end of the charger to the battery charging connector and the other end to a suitable

power supply capable of delivering 5 V/DC 1000 mA via USB A.

Charger LED Description

On Fully charged

Off Charging

b) Insert the transmitter batteries

1. Use a plus head screwdriver to open the

battery compartment.

2. Insert 3x AAA batteries, match polarities

as shown inside the compartment.

3. Replace the cover.

 UsenewbatteriesiftheLEDblinks

slowly after switching it on.

c) Insert the helicopter battery

• Slidethebatteryintothebatterycageandcheckthatitissecure.

• Do not connect the battery plug to the helicopter battery socket until you are ready for

takeoff.

d) Preight check

Loose, damaged, or missing parts can result in loss of control and further damage. To prevent

thisperformapreightcheck:

1. Batterypackisproperlyinserted.

2. Propeller blades are not damaged.

3. Blade grip tension is correct.

4. Connecting rods are not damaged or missing.

5. Tail blade is not damaged or missing.

 Seechapter“14.Repairsandmaintenance”onpage17.

12. Flying the helicopter

Important

• Pleasecompletethestepsoutlinedin“11.Gettingreadyforight”onpage11.

• Any time you disconnect the helicopter battery, switch the transmitter power off then

repeatthepairingprocessdescribedin“b)Takingoff”onpage15.

• Standatleast2mawayduringtakeoff.

• Thereshouldbe≥2mclearancefromobstaclesinalldirectionsbeforetakingight.

a) Controls

The helicopter will not automatically hover, use the throttle lever to control the height.

Transmitter Flight Description

Ascend:

Throttle lever up.

Descend:

Throttle lever down.

Rotate left:

Direction lever left.

Transmitter Flight Description

Rotate right:

Direction lever right.

Forward:

Direction lever up.

Reverse:

Direction lever down.

Emergency stop

Throttle lever

maximum down until

the helicopter lands

and the propellers

stop spinning.

b) Taking off

1. Pull the throttle lever all the way down and leave it there.

2. Switch the transmitter ON.

- TheLEDwillblinkslowlywhilewaitingtoconnecttothehelicopter.

- A beep will sound and the LED will be solid on when successfully paired.

3. Switch the helicopter ON.

- InsertthebatteryplugintothesocketonthehelicoptertoswitchitON.

- Theheadlightwillblinkslowly

4. Placethehelicopteronahorizontalsurface,facingawayfromyou,andthenstepbackat

least 5 meters.

5. Unlockthehelicopter.

- Push thethrottleleverallthe way up(theLEDwillash

quicklythenlightsolid).

- Pull the throttle lever all the way down (a long beep will

sound).

6. Thehelicopterisnowreadyforight.

7. Pushthethrottleleverupslowlytotakeight.

c) Landing

1. Make sure the landing area is clear, then slowly pull the throttle lever down until the

helicopter touches ground.

2. Pull the throttle lever down all the way to stop the blades from spinning.

3. Disconnect the helicopter battery.

d) Crash protection

Ifthehelicopterbladescollidewithanobjectduringight,thepropellerswillstopspinningand

the helicopter will automatically power off to avoid damage or injury.

Toresumeight:

1. Disconnect the helicopter battery.

2. Switch the transmitter OFF.

3. Performpreightchecks.See“d)Preightcheck”onpage12.

4. Takeoffagain.See“11.Gettingreadyforight”onpage11.

e) Low helicopter battery

• ChargethehelicopterbatteryifyouhearabeepingsoundandthehelicopterLEDblinks.

• If the battery runs out during use, the helicopter will slowly descend to the ground.

f) Adjust trim

Adjust the trim if the helicopter spins left or right on its own.

• Press once for small adjustments, press and hold for rapid adjustments.

• If there are no beeps it means you have reached the maximum number of adjustments.

• The default trim setting is indicated by a long beep. E.g. Pressing the left trim button 5x, then

pressingtherighttrimbutton5xwilltakeyoubacktothedefaultsetting.

• Settings will reset each time the helicopter and transmitter are powered off.

Flight Problem Trim adjustment

Helicopter

spins right

Press the left trim button until the

helicopter stops spinning right.

Helicopter

spins left

Press the right trim button until the

helicopter stops spinning left.

13. Finished ying

1. Land the helicopter.

2. Disconnect the helicopter battery.

3. Turn the transmitter power OFF.

14. Repairs and maintenance

Important

• Always replace damaged blades. Attach new blades in the correct position

(see below). Top blades = A, Bottom blades = B.

• Be careful not to damage parts when removing the tail blade or connection rod.

Blade tension screw

Blade tension screw connection rod

a) Replace propeller blade(s)

1. Release the blade tension screw for the affected blade(s).

2. Eachbladeismarkedwithaletter“A”or“B”.Replacethedamagedbladewiththecorrect

letter.

3. Replacethebladetensionscrew,makingsurethebladetensioniscorrect.

Blade tension: Slowly tighten the screw stopping at the point where the blades do not

“hangdown”whenthehelicopteristiltedonitsside.Thenslowlyreleasethescrew

tension until the blades hangs down freely without friction.

b) Replace tail blade

1. Pinch the tail blade and carefully pull straight up and

off as shown.

Important

Grip the base of the tail with your other

hand and do not use excessive force.

2. Push the new tail blade in all the way.

c) Replace damaged connection rod

1. Pinchthedamagedconnectionrodatthesockets,andpopitofftheballjoints.

2. Popthenewconnectorrodsocketsintotheballjoints

15. Care and cleaning

Important

Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions as

they can cause damage to the housing and malfunctioning e.g. damage to electronics

and discolouration of body.

• Before cleaning or servicing, remove the battery. Let all parts cool down completely.

• Remove all dust and dirt e.g. with a long-haired clean brush or compressed air.

• A soft cloth, slightly dampened, can be used to wipe the body.

16. Troubleshooting

Problem Cause Suggestion

Helicopter does

not respond.

Helicopter is

locked.

Unlockthehelicopter.Seesection:“b)Takingoff”

on page 15.

No battery. Recharge the battery.

Propellerskeep

spinning after

landing.

Throttle lever not

held in max. down

position.

Hold the throttle lever at the maximum down

position until the propellers stop spinning.

Cannot lift off. Propellers not

installed correctly

Seesection:“14.Repairsandmaintenance”on

page 17.

Helicopter cannot

yaftercrashing

Loose tail blade. Checkthatitisinsertedalltheway.Pushitinif

needed.

Damaged tail

blade(s).

Seesection:“14.Repairsandmaintenance”on

page 17.

Crash protection

has been

activated.

Seesection“d)Crashprotection”onpage16.

17. Declaration of Conformity (DOC)

Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau hereby declares that this

product conforms to the 2014/53/EU directive.

 ClickonthefollowinglinktoreadthefulltextoftheEUdeclarationofconformity:

www.conrad.com/downloads

 Selectalanguagebyclickingonaagsymbolandentertheproductordernumberinthe

search box. You can then download the EU declaration of conformity in PDF format.

18. Disposal

a) Product

Electronic devices are recyclable waste and must not be disposed of in the household

waste. At the end of its service life, dispose of the product in accordance with

applicable regulatory guidelines.

Remove any inserted (rechargeable) batteries and dispose of them separately from

the product.

b) (Rechargeable) batteries

You as the end user are required by law (Battery Ordinance) to return all used

(rechargeable) batteries. Disposing of them in the household waste is prohibited.

Contaminated (rechargeable) batteries are labeled with this symbol to indicate that

disposal in the domestic waste is forbidden. The designations for the heavy metals

involved are: Cd = Cadmium, Hg = Mercury, Pb = Lead (name on (rechargeable)

batteries, e.g. below the trash icon on the left).

Used (rechargeable) batteries can be returned to collection points in your municipality, our

stores or wherever (rechargeable) batteries are sold.

Youthusfulllyourstatutoryobligationsandcontributetotheprotectionoftheenvironment.

Page is loading ...

Reely 2282651 User manual

Reely 2282651 User manual

Related papers

Other documents