V I V O STAND-V100D User manual

Brand: V I V O

Model: STAND-V100D

Category: Flat panel desk mounts

Type: User manual

Pneumatic Arm Single Ultrawide Monitor

Desk Mount

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-v100d

SKU: STAND-V100D

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

PACKAGE CONTENTS

WARNING!

A (x1)

Arm

F (x1)

Pad

S-A (x1)

Spacer

T-A (x1)

4mm Allen

Wrench

M-C (x4)

M5 Washer

T-B (x1)

6mm Allen

Wrench

S-B (x1)

M8x25mm

Screw

S-C (x4)

M6x12mm

Screw

M-A (x4)

M4x12mm

Screw

M-B (x4)

M5x12mm

Screw

G (x1)

Grommet

Plate

H (x1)

Support

Plate

B (x1)

Upper Clamp

C (x1)

Lower Clamp

D (x1)

VESA Plate

E (x1)

Clamp Cable Clip

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualified technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product for

any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot

be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate

use.

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR

STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

TOOLS NEEDED

Phillips

Screwdriver

4.4-44 lbs

(2-20 kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

ASSEMBLY STEPS

STEP 1

STEP 2: Option A - Desk Clamp

Cut the shipping tie from Arm (A) while firmly holding the two halves close together. Slowly release

the pressure and allow it to gradually open up to reach full extension.

Assemble Upper Clamp (B) to the underside of Arm

(A) using M6x12mm Screws (S-C) and 4mm Allen

Wrench (T-A). Place Pad (F) to bottom of Upper

Clamp (B).

Loosen bolts on Lower Clamp (C) using 6mm Allen Wrench (T-B). Turn Clamp over and place

Support Plate (H) over bolt ends.

Slightly loosen back side screws on Lower Clamp (C), allowing 6mm to be exposed. Slide Lower

Clamp (C) into the appropriate keyholes of Upper Clamp (B) based on desktop thickness. Use

lower holes for desktops 50-85mm (2” to 3 3/8”) thick, and upper holes for desktops 10-58mm (3/8”

to 2 1/4”).

S-C

T-A

T-B

STEP 2: Option A - Desk Clamp - Continued

STEP 2: Option B - Grommet

Assemble Grommet Plate (G) to under side of Arm (A) using M6x12mm Screws (S-C) and 4mm Allen

Wrench (T-A). Apply Pad (F) to Grommet Plate (G).

Remove Bolts (C1) from Lower Clamp (C) using 6mm Allen Wrench (T-B). Insert one Bolt (C1) into

middle hole of Support Plate (H).

Secure screws on Lower Clamp (C) using 4mm Allen Wrench (T-A). Tighten lower bolts on Lower

Clamp (C) to secure to desktop using 6 mm Allen Wrench (T-B).

T-A

T-B

T-A S-C

Proceed to Step 3 at the bottom of Page 5

STEP 2: Option B - Grommet - Continued

If you are using an existing grommet hole, ensure that it is at least 10mm (3/8”) in diameter and no

more than 60mm (2 3/8”). Desktop should be between 10mm-48mm (3/8” to 1 7/8”) . For desktops

without an existing gromment hole, use a 3/8” (10mm) drill bit to drill through desktop.

EXISTING

GROMMET HOLE

DRILLING A

GROMMET HOLE

Place mount asembly over gromment hole and secure to

desktop using Support Plate (H), Bolt (C1), and 6mm Allen

Wrench (T-B).

STEP 3

Connect VESA Plate (D) to Arm (A) using Spacer (S-A), M8x25mm Screw (S-B), and 6mm Allen Wrench

(T-B). Ensure that hexagon side of space is facing upward towards VESA Plate (D). Remove Thumbscrew

(D1) from back of VESA Plate (D). Separate Front VESA Plate (D2) from Back VESA Plate (D3). Set aside.

T-B

S-A

S-B

T-B

STEP 5

STEP 6

STEP 4

To mount the monitor, begin by lining up the tabs on Front VESA Plate (D2) with the slots on Back VESA

Plate (D3). Insert tabs into slots and re-install Thumbscrew (D1) into Back VESA Plate (D3) to secure.

While holding the arm in the horizontal position, adjust the gas spring tension using 6mm Allen

Wrench (T-B).

Connect Front VESA Plate (D2) to back of

Monitor using appropriate Screws (M-A, M-B),

M5 Washers (M-C), and a Phillips Screwdriver.

M-A

M-B

M-C

ARM DROPS - If the arm drops,

turn the adjustment screw counter

clockwise until it holds the monitor

in a horizontal position.

How to adjust if...

ARM RISES - If the arm raises up,

turn the adjustment screw lockwise

until it holds the monitor in a

horizontal position.

CAUTION - To avoid damage to the monitor and mount, always

keep the arm in a horizontal position while making adjustments.

T-B

STEP 7

STEP 8

Remove Cable Cover (A1) from Arm (A) by sliding it forward. Route cables and replace Cover (A1).

Place Clamp Cable Clip (E) onto backside of assembly for additional cable management. 4mm and

6mm Allen Wrenches (T-A, T-B) can be stored in slots for future adjustments.

To keep mount stable, do not extend arm fully behind desktop edge.

Adjust the tilt using the 6mm Allen Wrench (T-B).

Adjust the monitor position as desired.

T-A

T-B

LAST UPDATED: 11/15/2022

REV1

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303

V I V O STAND-V100D User manual

Brand: V I V O

Model: STAND-V100D

Category: Flat panel desk mounts

Type: User manual

Download PDF

report

V I V O STAND-V100D User manual

V I V O STAND-V100D User manual

Related papers

Other documents