abetap B0CH8D52M6 User guide

B0CH8D52M6
Brand
abetap
Model
B0CH8D52M6
Type
User guide

abetap B0CH8D52M6 is a smart battery camera with a built-in infrared sensor for night vision, a microphone for audio recording, and a speaker for two-way communication. It also features a motion detection sensor that triggers recording when movement is detected. The camera can be controlled and accessed remotely via a mobile app, allowing you to view live footage, receive alerts, and adjust settings. It supports Wi-Fi connectivity and can be easily set up using a QR code. The camera comes with a rechargeable battery that lasts up to six months in standby mode.

abetap B0CH8D52M6 is a smart battery camera with a built-in infrared sensor for night vision, a microphone for audio recording, and a speaker for two-way communication. It also features a motion detection sensor that triggers recording when movement is detected. The camera can be controlled and accessed remotely via a mobile app, allowing you to view live footage, receive alerts, and adjust settings. It supports Wi-Fi connectivity and can be easily set up using a QR code. The camera comes with a rechargeable battery that lasts up to six months in standby mode.

Smart
Battery Camera
QUICK START GUIDE (X83)FCC ID: 2AXEK-X83
NOTE: The battery of your camera may drain faster below
32°F (0°C). When you receive low-battery alert on your app, it
is suggested to take the camera down and fully recharge
it indoor, or you can connect it to the power cable all the time.
Warranty Service
Thanks for your shopping and trust.
We have been optimizing our products and improve our
lifetime customer service to offer you a better shopping
experience. If you have any problems, please feel free to
send us an E-mail. We will solve your problems within
24 hours. In addition, your advice or suggestions will be
much appreciated and welcomed.
Product Service
Information: [email protected]
Service: [email protected]
More About Us
Website: www.abetap.com
User Guide
Charging Cable
Screws Set
Mounting Bracket
Camera
Infrared light
Lens
Indicator light
Human body
infrared sensor
Microphone
White light
Product Appearance
Android
Download
Download
App Store
Sign in to the app， connect to Wi-Fi and add the device according to the
prompts (please bring the device close to the router when configuring).
1. Download and install the app
Double click the power button to enter the network configuration
mode after the prompt tone.
Long press the power button for 3s to power on/off the device.
When connecting the camera for the first time, use the app
and follow the instruction to configure the camera network.
H
2) Click "Invite", and a QR code will be generated for sharing.
3) For the members you need to share, find "Add Friend's Camera" in
the "User" page to enter the scanning page.
4) Scan the QR code on your mobile phone, and you will receive the
confirmation notification after success. The sharing will be completed
after you agree.
The app will remind you to charge your camera when the battery is low.
* Up to six months in the standby mode
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC's RF Exposure guidelines, this
NOTE
equipment should be installed and operated with a minimum distance
of 20 cm between the radiator and your body.
A: Open the app and select your camera on the home page. Click the
share button on the home page or the "Share" in the camera settings to
enter the sharing page, and then click "Invite" to generate a QR code.
Your friends can now get some of the access rights by scanning the QR
code in your phone.
A: On Apple devices with iOS13 and above, you need to turn on the
"location permission" for the app in the system settings and change
it to "allow when using".
A: The built-in infrared lamp beads make the camera only show some
dim red lights when night vision is activated, but the image quality is
still clear under no light environment.
1. Q: Camera permission management: How to invite
family and friends to use my camera together?
2. Q: Why doesn't the Wi-Fi name appear when I connect
to Wi-Fi?
3. Q: Will the camera show red lights when the night vision
is activated?
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21

abetap B0CH8D52M6 User guide

B0CH8D52M6
Brand
abetap
Model
B0CH8D52M6
Type
User guide

abetap B0CH8D52M6 is a smart battery camera with a built-in infrared sensor for night vision, a microphone for audio recording, and a speaker for two-way communication. It also features a motion detection sensor that triggers recording when movement is detected. The camera can be controlled and accessed remotely via a mobile app, allowing you to view live footage, receive alerts, and adjust settings. It supports Wi-Fi connectivity and can be easily set up using a QR code. The camera comes with a rechargeable battery that lasts up to six months in standby mode.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents