ESAB ECD-120/ECI-120 User manual

ECD-15/ECI-15,

ECD-30/ECI-30,

ECD-60/ECI-60,

ECD-90/ECI-90,

ECD-120/ECI-120

Conventional Roller Beds

Instruction manual

0463 740 001 GB 20201125

Valid for: 950-xxx-xxxx

0463 740 001

- 3 -

1 SAFETY

......................................................................................................................................

5

1.1 Meaning of symbols

....................................................................................................

5

1.2 Non-compliant operation

............................................................................................

5

1.3 Safety precautions

......................................................................................................

5

2 INTRODUCTION

.........................................................................................................................

8

2.1 Equipment

....................................................................................................................

8

2.2 Purpose and function of roller beds

..........................................................................

8

2.3 Terminology used in this manual

...............................................................................

8

3 TECHNICAL DATA

.....................................................................................................................

9

3.1 ECD/ECI-15

...................................................................................................................

9

3.1.1 Drive unit, ECD-15

.............................................................................................

9

3.1.2 Idler unit, ECI-15

................................................................................................

10

3.2 ECD/ECI-30

...................................................................................................................

11

3.2.1 Drive unit, ECD-30

.............................................................................................

11

3.2.2 Idler unit, ECI-30

................................................................................................

12

3.3 ECD/ECI-60

...................................................................................................................

13

3.3.1 Drive unit, ECD-60

.............................................................................................

13

3.3.2 Idler unit, ECI-60

................................................................................................

14

3.4 ECD/ECI-90

...................................................................................................................

15

3.4.1 Drive unit, ECD-90

.............................................................................................

15

3.4.2 Idler unit, ECI-90

................................................................................................

16

3.5 ECD/ECI-120

.................................................................................................................

17

3.5.1 Drive unit, ECD-120

...........................................................................................

17

3.5.2 Idler unit, ECI-120

..............................................................................................

18

4 INSTALLATION

...........................................................................................................................

19

4.1 Location

........................................................................................................................

19

4.2 Lifting instructions

......................................................................................................

19

4.3 Adjusting the wheel stands

........................................................................................

20

4.4 Adjusting the included angle

.....................................................................................

21

4.5 Installation procedure

.................................................................................................

21

4.6 PEK setup

....................................................................................................................

22

4.7 Roller bed configurations

...........................................................................................

23

5 OPERATION

...............................................................................................................................

24

5.1 Roller bed details

........................................................................................................

24

5.2 Control panel

...............................................................................................................

24

5.3 Wireless remote - control pendant

............................................................................

25

5.4 Switch the mains power on

........................................................................................

26

5.5 Operating the roller beds

............................................................................................

27

5.6 Operation safety

..........................................................................................................

27

5.7 Welding

.........................................................................................................................

29

5.8 Stopping the roller beds

.............................................................................................

29

6 MAINTENANCE

..........................................................................................................................

30

6.1 General

.........................................................................................................................

30

6.2 Storage

.........................................................................................................................

30

TABLE OF CONTENTS

0463 740 001

- 4 -

6.3 Repair and maintenance

.............................................................................................

30

6.4 Cleaning

.......................................................................................................................

31

6.5 Breakdowns

.................................................................................................................

31

6.6 Gearmotors

..................................................................................................................

31

6.6.1 Gearmotors inspection and maintenance

...........................................................

31

6.6.2 Gearbox lubrication

............................................................................................

31

6.7 Inverters

.......................................................................................................................

32

6.8 Bearings

.......................................................................................................................

32

6.9 PU wheels

....................................................................................................................

32

7 TROUBLESHOOTING

................................................................................................................

33

8 ORDERING SPARE PARTS

.......................................................................................................

34

WIRING DIAGRAM

................................................................................................................................

36

ORDERING NUMBERS

.........................................................................................................................

41

ACCESSORIES

.....................................................................................................................................

42

SPARE PARTS

......................................................................................................................................

43

SPARE PARTS - ECD-15 Mechanical parts list - Drive section

........................................................

44

SPARE PARTS - ECI-15 Mechanical parts list - Idler section

...........................................................

45

SPARE PARTS - ECD-30 Mechanical parts list - Drive section

........................................................

46

SPARE PARTS - ECI-30 Mechanical parts list - Idler section

...........................................................

48

SPARE PARTS - ECD-60 Mechanical parts list - Drive section

........................................................

49

SPARE PARTS - ECI-60 Mechanical parts list - Idler section

...........................................................

51

SPARE PARTS - ECD-90 Mechanical parts list - Drive section

........................................................

52

SPARE PARTS - ECI-90 Mechanical parts list - Idler section

...........................................................

54

SPARE PARTS - ECD-120 Mechanical parts list - Drive section

......................................................

55

SPARE PARTS - ECI-120 Mechanical parts list - Idler section

.........................................................

57

SPARE PARTS - Control cabinet

.........................................................................................................

58

SPARE PARTS - Electrical parts - Control cabinet

............................................................................

60

SPARE PARTS - Wireless control system

..........................................................................................

61

1  SAFETY

0463 740 001

- 5 -

1 SAFETY

1.1 Meaning of symbols

As used throughout this manual: Means Attention! Be Alert!

DANGER!

Means immediate hazards which, if not avoided, will result in immediate, serious

personal injury or loss of life.

WARNING!

Means potential hazards which could result in personal injury or loss of life.

CAUTION!

Means hazards which could result in minor personal injury.

WARNING!

Before use, read and understand the instruction manual and

follow all labels, employer´s safety practices and Safety Data

Sheets (SDSs).

1.2 Non-compliant operation

CAUTION!

These roller beds are not suitable for the following:

• Any vessel which is heavier than the maximum weight limit of the roller beds.

• Any vessel that is larger/smaller than the maximum/minimum diameter that can

be supported.

• If the roller beds have polyurethane or rubber tires Do not use on preheated

vessels above 60 °C.

1.3 Safety precautions

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or

near the equipment observes all the relevant safety precautions. Safety precautions must meet the

requirements that apply to this type of equipment. The following recommendations should be observed

in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the equipment.

Incorrect operation of the equipment may lead to hazardous situations which can result in injury to the

operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:

• its operation

• location of emergency stops

• its function

• relevant safety precautions

• welding and cutting or other applicable operation of the equipment

2. The operator must ensure that:

• no unauthorised person is stationed within the working area of the

equipment when it is started up

• no-one is unprotected when the arc is struck or work is started with the

equipment

1   SAFETY

0463 740 001

- 6 -

3. The workplace must:

• be suitable for the purpose

• be free from drafts

4. Personal safety equipment:

• Always wear recommended personal safety equipment, such as safety

glasses, flame-proof clothing, safety gloves

• Do not wear loose-fitting items, such as scarves, bracelets, rings, etc.,

which could become trapped or cause burns

5. General precautions:

• Make sure the return cable is connected securely

• Work on high voltage equipment may only be carried out by a qualified

electrician

• Appropriate fire extinguishing equipment must be clearly marked and close

at hand

• Lubrication and maintenance must not be carried out on the equipment

during operation

WARNING!

Arc welding and cutting can be injurious to yourself and others. Take precautions when

welding and cutting.

ELECTRIC SHOCK - Can kill

• Do not touch live electrical parts or electrodes with bare skin, wet gloves or

wet clothing

• Insulate yourself from work and ground.

• Ensure your working position is safe

ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health

• Welders having pacemakers should consult their physician before welding.

EMF may interfere with some pacemakers.

• Exposure to EMF may have other health effects which are unknown.

• Welders should use the following procedures to minimize exposure to EMF:

○ Route the electrode and work cables together on the same side of

your body. Secure them with tape when possible. Do not place your

body between the torch and work cables. Never coil the torch or

work cable around your body. Keep welding power source and

cables as far away from your body as possible.

○ Connect the work cable to the workpiece as close as possible to the

area being welded.

FUMES AND GASES - Can be dangerous to health

• Keep your head out of the fumes

• Use ventilation, extraction at the arc, or both, to take fumes and gases away

from your breathing zone and the general area

ARC RAYS - Can injure eyes and burn skin

• Protect your eyes and body. Use the correct welding screen and filter lens

and wear protective clothing

• Protect bystanders with suitable screens or curtains

NOISE - Excessive noise can damage hearing

Protect your ears. Use earmuffs or other hearing protection.

1  SAFETY

0463 740 001

- 7 -

MOVING PARTS - Can cause injuries

• Keep all doors, panels and covers closed and securely in place. Have only

qualified people remove covers for maintenance and troubleshooting as

necessary. Reinstall panels or covers and close doors when service is

finished and before starting the roller beds.

• Stop the roller beds before installing or connecting unit.

• Keep hands, hair, loose clothing and tools away from moving parts.

FIRE HAZARD

• Sparks (spatter) can cause fire. Make sure therefore that there are no

inflammable materials nearby

HOT SURFACE - Parts can burn

• Do not touch parts bare handed.

• Allow cooling period before working on equipment.

• To handle hot parts, use proper tools and/or insulated welding gloves to

prevent burns.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION!

Class A equipment is not intended for use in residential

locations where the electrical power is provided by the public

low-voltage supply system. There may be potential difficulties in

ensuring electromagnetic compatibility of class A equipment in

those locations, due to conducted as well as radiated

disturbances.

NOTE!

Dispose of electronic equipment at the recycling facility!

In observance of European Directive 2012/19/EC on Waste

Electrical and Electronic Equipment and its implementation in

accordance with national law, electrical and/or electronic

equipment that has reached the end of its life must be disposed

of at a recycling facility.

As the person responsible for the equipment, it is your

responsibility to obtain information on approved collection

stations.

For further information contact the nearest ESAB dealer.

ESAB has an assortment of welding accessories and personal protection equipment for

purchase. For ordering information contact your local ESAB dealer or visit us on our website.

2   INTRODUCTION

0463 740 001

- 8 -

2 INTRODUCTION

This Instruction manual describes the use and maintenance of the conventional roller beds, referred to

as roller beds in this document. Actions that must be carried out by the manufacturer are not included

in this manual.

This manual is part of the roller beds. Keep a copy of the manual with the roller beds and the original

in a safe place. If the roller beds are sold, supply the manual with it.

The pictures and diagrams used in this manual are for illustrative purposes only to help explain

instructions in the text. The equipment supplied may differ slightly.

2.1 Equipment

The roller bed drive is supplied with:

• Drive units

• Mounted control cabinet

• Wireless remote - control pendant

• Base frame

• Instruction manual

The roller bed idler is supplied with:

• Idler units

• Base frame

2.2 Purpose and function of roller beds

The roller beds are designed to aid the welding of cylindrical vessels.

By using the independent drive and idler units, vessels of varying lengths can be placed on the roller

beds supported on the roller bed wheels. The wheels can be adjusted on the base frame to

accommodate different vessel diameters.

2.3 Terminology used in this manual

Drive unit Roller bed section with powered wheels.

Idler unit Roller bed section with freewheeling wheels.

Roller bed set A set consists of one drive unit and one or more idler units.

Base frame The frame the drive or idler wheels are mounted on. These are pre-drilled

so that the wheel stands can be positioned for different vessel diameters.

Wheel stand The stand which houses the roller bed wheels. This is bolted down to the

baseframe.

Control panel Electrical control box mounted on the drive unit.

Wireless remote -

control pendant

A wireless operator hand control pendant.

Receiver The receiver that communicates with the wireless remote-control pendant.

Vessel Any component or device that is handled on the roller bed set.

3  TECHNICAL DATA

0463 740 001

- 9 -

3 TECHNICAL DATA

3.1 ECD/ECI-15

3.1.1 DRIVE UNIT, ECD-15

ECD-15

Max loading capacity 7500 kg (16535lb)

Turning capacity 22500kg (49604 lb)

Turning drive motor 2×0.18kW

Turning speed 200-2000mm/min (5.51-78.74in./min)

Workpiece diameter minimum Ø480mm (18.90in.) at 60° included angle

Workpiece diameter maximum Ø5700mm (224.41 in.) at 45° included angle

Mains supply 380-440V, 3phase, 50Hz

Mains fuse 16A

Roller type Polyurethane (90 °C / 92°A Shore)

Roller width / diameter 90 mm (3.54in.) / 400mm (15.74in.)

Dimensions (L × W × H) 3647 × 774 × 700 mm (143.58 × 30.47 ×27.55in.)

C-C

440, 630, 820, 1200, 1580, 1960, 2340 mm

(17.32, 24.80, 32.28, 47.24, 62.20, 77.16, 92.12in.)

Weight 645kg (1422lb)

Wireless remote - control

pendant

Wireless

Control voltage 24V

Operation temperature -15 to +40 °C

PEK settings, ECD-15

Gear 1 N1:N2 100:1

3   TECHNICAL DATA

0463 740 001

- 10 -

Gear 2 N1:N2 10:1

Gear 3 N1:N2 1:1

Wheel diameter 400mm

High manual speed 200cm/min

Frequency ratio N1 50 Hz

Frequency ratio N2 50Hz

Max motor rpm 1592

3.1.2 Idler unit, ECI-15

ECI-15

Max loading capacity 7500 kg (16535lb)

Roller type Polyurethane (90 °C / 92°A Shore)

Roller width / diameter 90 mm (3.54in.) / 400mm (15.74in.)

Dimensions (L × W × H) 2790 × 600 × 700 mm (109.84 × 23.62 × 27.55in.)

C - C

440, 630, 820, 1200, 1580, 1960, 2340 mm

(17.32, 24.80, 32.28, 47.24, 62.20, 77.16, 92.12in.)

Weight 475kg (1047lb)

3  TECHNICAL DATA

0463 740 001

- 11 -

3.2 ECD/ECI-30

3.2.1 DRIVE UNIT, ECD-30

ECD-30

Max loading capacity 15000 kg (33069lb)

Turning capacity 45000kg (99208 lb)

Turning drive motor 2×0.37kW

Turning speed 200-2000mm/min (5.51-78.74in./min)

Workpiece diameter minimum Ø480mm (18.90in.) at 60° included angle

Workpiece diameter maximum Ø5700mm (224.41 in.) at 45° included angle

Mains supply 380-440V, 3phase, 50Hz

Mains fuse 16A

Roller type Polyurethane (90 °C / 92°A Shore)

Roller width / diameter 2×90 mm (2×3.54in.) / 400mm (15.74in.)

Dimensions (L × W × H) 3874 × 810 × 700 mm (152.52 × 31.88 ×27.55in.)

C-C

440, 630, 820, 1200, 1580, 1960, 2340mm

(17.32, 24.80, 32.28, 47.24, 62.20, 77.16, 92.12in.)

Weight 865 kg (1907lb)

Wireless remote - control

pendant

Wireless

Control voltage 24V

Operation temperature -15 to +40 °C

PEK settings, ECD-30

Gear 1 N1:N2 100:1

Gear 2 N1:N2 10:1

Gear 3 N1:N2 1:1

3   TECHNICAL DATA

0463 740 001

- 12 -

Wheel diameter 400mm

High manual speed 200cm/min

Frequency ratio N1 50 Hz

Frequency ratio N2 50Hz

Max motor rpm 1592

3.2.2 Idler unit, ECI-30

ECI-30

Max loading capacity 15000 kg (33069 lb)

Roller type Polyurethane (90 °C / 92°A Shore)

Roller width / diameter 2×90 mm (2×3.54in.) / 400mm (15.74in.)

Dimensions (L × W × H) 2790 × 700 × 700 mm (109.84 × 27.55 × 27.55in.)

C-C

440, 630, 820, 1200, 1580, 1960, 2340mm

(17.32, 24.80, 32.28, 47.24, 62.20, 77.16, 92.12in.)

Weight 625kg (1378lb)

3  TECHNICAL DATA

0463 740 001

- 13 -

3.3 ECD/ECI-60

3.3.1 DRIVE UNIT, ECD-60

ECD-60

Max loading capacity 30000 kg (66139lb)

Turning capacity 90000kg (198416 lb)

Turning drive motor 2×0.75kW

Turning speed 200-2000mm/min (5.51-78.74in./min)

Workpiece diameter minimum Ø700mm (27.56in.) at 60° included angle

Workpiece diameter maximum Ø7600mm (299.21 in.) at 45° included angle

Mains supply 380-440V, 3 phase, 50Hz

Mains fuse 16A

Roller type Polyurethane (90 °C / 92°A Shore)

Roller width / diameter 2×90 mm (2×3.54in.) / 400mm (15.74in.)

Dimensions (L × W × H) 4920 × 896 × 900 mm (193.70 × 35.28 × 35.43in.)

C-C

640, 850, 1060, 1480, 1900, 2320, 2740, 3160mm

(25.19, 33.46, 41.73, 58.26, 74.80, 91.33, 107.87, 124.40in.)

Weight 1390 kg (3064lb)

Wireless remote - control

pendant

Wireless

Control voltage 24V

Operation temperature -15 to +40 °C

PEK settings, ECD-60

Gear 1 N1:N2 100:1

Gear 2 N1:N2 10:1

Gear 3 N1:N2 1:1

3   TECHNICAL DATA

0463 740 001

- 14 -

Wheel diameter 580mm

High manual speed 200cm/min

Frequency ratio N1 50 Hz

Frequency ratio N2 50Hz

Max motor rpm 1098

3.3.2 Idler unit, ECI-60

ECI-60

Max loading capacity 30000 kg (66139lb)

Roller type Polyurethane (90 °C / 92°A Shore)

Roller width / diameter 180 mm (7.08in.) / 580 mm (22.83in.)

Dimensions (L × W × H) 3740 × 700 × 900 mm (147.24 × 27.55 × 35.43in.)

C-C

640, 850, 1060, 1480, 1900, 2320, 2740, 3160mm

(25.19, 33.46, 41.73, 58.26, 74.80, 91.33, 107.87, 124.40in.)

Weight 1055kg (2326lb)

3  TECHNICAL DATA

0463 740 001

- 15 -

3.4 ECD/ECI-90

3.4.1 DRIVE UNIT, ECD-90

ECD-90

Max loading capacity 45000 kg (66139lb)

Turning capacity 135000kg (297624 lb)

Turning drive motor 2×1.0kW

Turning speed 200-2000mm/min (5.51-78.74in./min)

Workpiece diameter minimum Ø700mm (27.56in.) at 60° included angle

Workpiece diameter maximum Ø7600mm (299.21 in.) at 45° included angle

Mains supply 380-440V, 3 phase, 50Hz

Mains fuse 16A

Roller type Polyurethane (90 °C / 92°A Shore)

Roller width / diameter 250 mm (9.84in.) / 580 mm (22.83in.)

Dimensions (L × W × H) 5054× 1028 × 900 mm (198.98 × 40.47 × 35.43in.)

C-C

640, 850, 1060, 1480, 1900, 2320, 2740, 3160mm

(25.19, 33.46,41.73, 58.26, 74.80, 91.33, 107.87, 124.40in.)

Weight 1895kg (4178 lb)

Wireless remote - control

pendant

Wireless

Control voltage 24V

Operation temperature -15 to +40 °C

PEK settings, ECD-90

Gear 1 N1:N2 100:1

Gear 2 N1:N2 10:1

Gear 3 N1:N2 1:1

3   TECHNICAL DATA

0463 740 001

- 16 -

Wheel diameter 580mm

High manual speed 200cm/min

Frequency ratio N1 50 Hz

Frequency ratio N2 50Hz

Max motor rpm 1098

3.4.2 Idler unit, ECI-90

ECI-90

Max loading capacity 45000 kg (99208lb)

Roller type Polyurethane (90 °C / 92°A Shore)

Roller width / diameter 250 mm (9.84in.) / 580 mm (22.83in.)

Dimensions (L × W × H) 3740 × 800 × 900 mm (147.24 × 31.49 × 35.43in.)

C-C

640, 850, 1060, 1480, 1900, 2320, 2740, 3160mm

(25.19, 33.46, 41.73, 58.26, 74.80, 91.33, 107.87, 124.40in.)

Weight 1430kg (3153 lb)

3  TECHNICAL DATA

0463 740 001

- 17 -

3.5 ECD/ECI-120

3.5.1 DRIVE UNIT, ECD-120

ECD-120

Max loading capacity 60000 kg (132277 lb)

Turning capacity 180000kg (396832 lb)

Turning drive motor 2×1.5kW

Turning speed 200-2000mm/min (7.87-78.74in./min)

Workpiece diameter minimum Ø700mm (27.56in.) at 60° included angle

Workpiece diameter maximum Ø7600mm (299-21 in.) at 45° included angle

Mains supply 380-440V, 3 phase, 50Hz

Mains fuse 16A

Roller type Polyurethane (90 °C / 92°A Shore)

Roller width / diameter 2×180 mm (2×7.08in.) / 580 mm (22.83in.)

Dimensions (L × W × H) 5300 × 1230 × 900 mm (208.66 × 48.42 × 35.43in.)

C-C

640, 850, 1060, 1480, 1900, 2320, 2740, 3160 mm

(25.19, 33.46,41.73, 58.26, 74.80, 91.33, 107.87, 124.40in.)

Weight 2600 kg (5732 lb)

Wireless remote - control

pendant

Wireless

Control voltage 24V

Operation temperature -15 to +40 °C

PEK settings, ECD-120

Gear 1 N1:N2 100:1

Gear 2 N1:N2 10:1

Gear 3 N1:N2 1:1

3   TECHNICAL DATA

0463 740 001

- 18 -

Wheel diameter 580mm

High manual speed 200cm/min

Frequency ratio N1 50 Hz

Frequency ratio N2 50Hz

Max motor rpm 1098

3.5.2 Idler unit, ECI-120

ECI-120

Max loading capacity 60000 kg (132277 lb)

Roller type Polyurethane (90 °C / 92°A Shore)

Roller width / diameter 2×180 mm (2×7.08in.) / 580 mm (22.83in.)

Dimensions (L × W × H) 3740 × 900 × 900 mm (147.24 × 35.43 × 35.43in.)

C-C

640, 850, 1060, 1480, 1900, 2320, 2740, 3160mm

(25.19, 33.46, 41.73, 58.26, 74.80, 91.33, 107.87, 124.40in.)

Weight 1895 kg (4178 lb)

4  INSTALLATION

0463 740 001

- 19 -

4 INSTALLATION

4.1 Location

WARNING!

Always ensure that there is sufficient space around the roller beds.

Make sure to have suitable access and enough space around the roller beds, including the vessel

when loaded. Position it to allow unhindered loading and unloading of vessels onto the roller beds by

overhead crane or other lifting devices

4.2 Lifting instructions

Use correctly rated overhead cranes or forklift trucks to move the roller beds.

Lifting by crane

The roller beds can be lifted by using the lifting points on the roller bed wheel stands. Use one lifting

point on each side of the wheel stand, 4 lifting points in all. The recommended angle between the

chain and the lifting points on the roller beds is 60°.

Place the roller beds on a smooth, level, hard floor that is capable of taking the weight of the roller bed

and vessel, over the contact area of the roller bed with the floor.

The distances between the base frames should match the vessel dimensions. If the vessel is perfectly

symmetrical and one drive with one idler is used, place the drive unit and the idler unit on one-third of

the way along the vessel's length to ensure that each section carries an equal load.

If one end of the vessel is heavier, move the drive or idler section closer to this end to balance the

loading on each section.

CAUTION!

Balance the loading equally between the drive and idler sections. Failure to do so can

result in overloading one of the sections, which will cause the wheels slipping when trying

to rotate the vessel. It can also result in back-driving, where the vessel can continue to

rotate after stopping the roller beds. This must be rectified by correctly positioning the drive

and idler section, failure to do so will cause damage to the equipment.

WARNING!

When a direction button (forward or reverse) is pressed, the roller beds begin to turn the

vessel.

4   INSTALLATION

0463 740 001

- 20 -

4.3 Adjusting the wheel stands

The positions of the two wheel stands on the base frame must be adjusted to load vessels of different

diameters.

1. Unbolt the wheel stand from the base frame.

2. Use an overhead crane to lift the wheel stand using the lifting points.

3. Move the wheel stand to the required position for the diameter of the vessel.

4. Bolt the wheel stands back onto the base frame using all the bolts, and tighten to the

correct torque i.e. M12 (8.8) 81 Nm and M16 (8.8) 197 Nm.

5. See tables and the picture below for correct distances between the two wheels

stands.

Suitable centre to centre distance (C -C) in relation to workpiece diameter

ECD-15, ECI-15, ECD-30, ECI-30

Wheelstandposition C- C (mm) Min object Ø (mm) Max object Ø (mm)

A 440 480 750

B 630 750 1240

C 820 1240 1740

D 1200 1740 2730

E 1580 2730 3700

F 1960 3600 4700

G 2340 4300 5700

ECD-60, ECI-60, ECD-90, ECI-90, ECI-120, ECI-120

Wheelstandposition C- C (mm) Min object Ø (mm) Max object Ø (mm)

A 640 700 1090

B 850 1090 1640

C 1060 1540 2180

D 1480 2180 3280

E 1900 3220 4300

F 2320 4100 5400

G 2740 4900 6500

H 3160 5800 7600

Page is loading ...

ESAB ECD-120/ECI-120 User manual

This manual is also suitable for

ESAB ECD-120/ECI-120 User manual

Related papers

Other documents