Vitek VTC-IR4MZ39 User manual

FEATURES:

• 1/2.9” 6.64 MegaPixel Sony STARVIS® CMOS Sensor

• 4 MegaPixel Coax Based Camera (2560x1440px @ 30/25fps)

• Outstanding Low Light Performance with Sony STARVIS® Sensor

• 1500’ HD-Analog Transmission Distance over Coax (Depending on Cable Characteristics

and Integrity)

• Premium 4MP Multi-format Video Output, Digital: EX-SDI 1.0/ 2.0/ 2.1 (4MP/2MP/1.3MP),

HD-SDI (2MP/1.3MP) HD-Analog: TVI Mode (4MP/2MP/1.3MP), AHD Mode (4MP/2MP),

CVBS Test Monitor Out

• F= 3.2~9mm Motorized Zoom Lens with Auto Focus

• Automatically Removable IR Cut Filter by Dual Filter Switch

• True WDR (Wide Dynamic Range) @30/25fps

• 120dB Dynamic Range with DOL(Digital OverLap) WDR @30/25fps

• ROI (Region of Interest) WDR @30/25fps

• Improved Noise Reduction with XD-NR

• DIS (Digital Image Stabilization) Function

• POI Zoom (Point Of Interest), Smart Motion Zoom, Preset Zoom, Home Position

• Privacy Mask, Defog, Sens-up(~x32), D-WDR, BLC/HLC, Mirror/Flip, Flickerless, Brightness,

Smart IR, Lens Initialize, Title Set, Color D/N

• High performance at Low Light Sensitivity (Sens-up On)

• Variety of Resolution : 1440p/1080p/720p Without Loss of FOV (Field of View)

• OSD Menu for Easy Installation and Maintenance

• Circuit Protection Protects Against Faulty Connection in Power Polarity

• Isolated Power Supply Protects Against Ground Loop Problem

• COC Control through HD-TVI (Pelco-C®) or AHD

• IP68 (VTD-VD4MZ39, VTC-IR4MZ39), IK10 (VTD-VD4MZ39)

• 12VDC, 24VAC Operation

VIRTUOSO HI DEFINITION

OVER COAX CAMERAS

Premium 4 Megapixel Indoor/Outdoor

6-in-1 HD/EX-SDI / TVI / AHD / CVI /

CVBS Motorized Varifocal Cameras

COAX

VTC-CB4MZ39

VTC-IR4MZ39

VTD-VD4MZ39

VITEK

Table of Contents

Safety Precautions.............................................. 3-4

Overview: VTC-CB4MX39............................... 5-7

Overview: VTD-VD4MZ39............................... 8-15

Overview: VTC-IR4MZ39................................. 16-20

Connections: VTD-VD4MZ39, VTC-IRMZ39... 21

OPERATING INSTRUCTIONS.................... 22-38

OSD Menu.......................................... 22-24

Zoom / Focus..................................... 24-26

Exposure.............................................. 27-28

WDR.................................................... 29-30

XD-DNR............................................. 31

Day / Night.......................................... 31-33

Picture Adjustment............................ 33-35

Special Functions.............................. 35-37

System.................................................. 37-38

Detailed Speciﬁcations.................................... 39-41

Accessories........................................................ 43

Warranty Information........................................ 44

2 3

Safety Precautions

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

To prevent electric shocks and risk of fire hazards, do NOT use other than with

a specific power source.

The symbol is intended to alert the user to the presence of important

operating and maintenance(servicing) instructions in the literature

accompanying the unit.

The symbol is intended to alert the user to the presence of uninsulated

"dangerous voltage" within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

Warning :

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

his own expense.

Caution :

Any changes or modifications in the construction of this device which are not expressly

approved by the party responsible for compliance could void the user's authority

to operate the equipment.

Mains power quality should be that of a typical commercial environment. If the user

of the model requires continued operation during power mains interruptions, it is

recommended that the model be powered from an uninterruptible power supply

(UPS) or a battery.

3

Safety Precautions

NOTICE

The images used in this instruction manual are processed to help comprehension

and may differ from actual video of the camera.

Avoid installing areas where has shock or vibration which results in the problems.

Pay attention to safety when laying the connection cable and observe that the cable

is not subjected to heavy loads, kinks or damage and no moisture can get in.

The warranty becomes void if repairs are undertaken by unauthorized persons.

Maintenance and repair have to be carried out only by authorized service centers.

Use only a mild detergent to clean the housing.

The camera should never be operated beyond the technical specifications.

This can lead to destruction.

The camera should never be operated in water.

Limited Product Warranty

VITEK products carry a three (3) year limited warranty. VITEK warrants to

the purchaser that products manufactured by VITEK are free of any rightful

claim of infringement or the like, and when used in the manner intended,

will be free of defects in materials and workmanship for a period of three

(3) years, or as otherwise stated above, from the date of purchase by the

end user. This warranty is nontransferable and extends only to the original

buyer or end user customer of a VITEK Authorized Reseller.

The product must have been used only for its intended purpose, and not

been subjected to damage by misuse, willful or accidental damage, caused

by excessive voltage or lightning.

The product must not have been tampered with in any way or the

guarantee will be considered null and void.

This guarantee does not affect your statutory rights.

Contact your local VITEK Reseller should servicing become necessary.

VITEK makes no warranty or guarantee whatsoever with respect to

products sold or purchased through unauthorized sales channels. Warranty

support is available only if product is purchased through a VITEK

Authorized Reseller.

4 5

Composition - VTC-CB4MX39

Dimensions

Operating InstructionsCamera

unit : inches (mm)

4.45 (113)

Ø2.13 (54)

4.92 (125)

2.84 (72)

2.99 (76)

5

Part Names - VTC-CB4MX39

REAR VIEW

• Extreme care should be taken NOT to scratch the window in front of the lens.

• Care should be taken so the cable is NOT damaged, kinked or exposed

to hazardous areas.

• Do not expose the camera directly to a strong light source such as the sun

or spotlights.

CAUTION

OSD Control Joy stick

Power input terminal

(AC24V/DC12V)

RS-485 / IR connector

Video format selection Switch

HD-Analog output connector

Power LED

HD-SDI/EX-SDI output connector

EX-SDIHD-SDI

HD-ANALOG

CONTROL

POWER

Front Case

Window

Rear Case

Mount Holes

(Top / Bottom)

6 7

Installation Instructions - VTC-CB4MX39

Power Supply Connections

Using OSD Controller

The Camera can work with either AC24V or DC12V, dual voltage power.

Primary and secondary grounds are completely isolated to avoid a

possible ground-loop problem.

1) SET ( ) : Access to the menu or enter the setting.

To enter the main menu, press the Set Key down.

2) UP/DOWN ( ) : Choose the desired sub-menu and move the

cursor up or down.

3) LEFT/RIGHT (

: Set up the value of the selected menu. Used to

adjust the desired menu selection and to move the cursor left or right.

Description of the OSD control operation

4) ‘denotes pressing straight down for 2 seconds

Setup menu can be accessed and controlled by OSD control joystick

on the rear of the camera unit. Five commands are available

with the joystick.

i

HD-SDI or EX-SDI is selectable by Video format switch only.

TVI mode or AHD mode is selectable in the menu only.

(SYSTEM> ANALOG MODE)

OSD Control Joy Stick

Video format Switch

EX-SDIHD-SDI

HD-ANALOG

CONTROL

POWER

Description of the Auto Focus Zoom, Motorized ZOOM&FOCUS adjustment

1) : Zoom In

2)

3) : Focus Near

4)

(*) Works only when OSD Menu is inactive.

7

Composition - VTD-VD4MZ39

Torque Wrench:

.12” (3mm) (1pc)

Plastic Anchor:

.24 x 1.18” (6 x 30mm) (4pcs)

Mounting Screw:

.16 x 1.18” (4 x 30mm) (4pcs)

Dome Camera

Connector fixing Screw:

.1” x .24” (2.6 x 6mm) (1pc)

Mounting

Template

Operating

Instructions

Video Sub-out

Cable (1pc)

Assembly Screw:

.16 x .55” (4 x 14mm) (3pcs)

Dome Camera

Surface mount

Conduit Spacer &

Conduit hole cap(1set)

8 9

Dimensions - VTD-VD4MZ39

Ø5.51 (140)

Ø3.93 (100)

4.69 (119)

Ø4.02 (102)

Ø5.51 (140)

2.64 (67)

4.69 (119)

1.46 (37)

3.23 (82)

[ Flush mount ] [ Surface mount ]

PCD Ø4.72 (120)

3-Ø.17 (4.2)

unit : inches (mm)

9

SURFACE MOUNT

Part Names - VTD-VD4MZ39

BUBBLE DOME

3-AXIS GIMBAL

DOME COVER

SAFTY WIRE

FLUSH MOUNT

LENS

POWER CABLE

VIDEO OUTPUT

[ BOTTOM VIEW ]

POWER SUPPLY

CONNECTOR

POWER

CABLE

OSD Menu Control board

10 11

Installation Instructions - VTD-VD4MZ39

1. Locate the mounting template at the installation position and drill the ceiling or

wall if needed.

2. Open the dome cover by loosening screws (.16 x .47” / 4 x 12mm).

Use the torque wrench supplied.

4. Set the camera’s viewing angle and focus.

5. Put the dome cover on the dome base unit and tighten the assembly screws.

- Place the dome base unit on pre-drilled position and attach it through using

mounting screws (16 x 1.18” / 4 x 30mm).

- Route the Power & Ethernet cable to the connecting place.

- Place the surface mount on a pre-drilled position and attach it through using

mounting screws(.16 x 1.18” / 4 x 30mm). Assemble the cable pipe,

otherwise tighten a pipe hole cap with PM screw (

.1 x .24” / 2.6 x 6mm).

- Route the Power & Ethernet cable to the connecting place.

- Affix the dome base unit to the surface mount using the assembly screws

(.16 x .55” / 4 x 14mm). Before securing the dome base make sure the assembly

holes are aligned with the surface mount assembly holes.

A. Flush mount type:

B. Surface

mount type:

Assembly Screw

Torque Wrench

Assembly Screw

Mounting Screw

A

Flush mount type

B

Surface mount type

(.16 x .55” / 4 x 14mm)

(.16 x .47” / 4 x 12mm)

(16 x 1.18” / 4 x 30mm)

11

Installation Instructions - VTD-VD4MZ39

• Pole mount

adaptor

• Tilted mount

• Wall mount

• Tilted junction

mount

• In the case of installation with Flush / Surface / Tilted mount, IP protection

rating is not guaranteed.

• If power or Video connectors are exposed to water or rain, a sunshield is

necessary.

• Extreme care should be taken NOT to scratch the bubble dome surface while

installing or adjusting the camera.

• Care should be taken so the cable is NOT damaged, kinked or exposed in

to hazardous areas.

• Tighten the dome cover fixing screws so that there is NO gap

between the Lens hood and clear bubble to avoid light inflow from IR LEDs.

CAUTION

• Wall mount

Sunshield

12 13

Installation Instructions - VTD-VD4MZ39

Option 2.

Installation with Surface mount / Tilted mount

Option 1.

Installation with Flush mount / Tilted Junction mount

3

1

Cable Holder

Video Output

Cables

2

Cable is unattached to the Dome base.

Connect the power cable to their repective connections.

Cable is unattached to the Dome base.

Tie up the VIDEO OUTPUT cables with cable holder.

Tie up the POWER SUPPLY cable with cable holder as illustrated.

Connect the wiring connector to their repective connections.

Cable Holder

Power Supply

13

Installation Instructions - VTD-VD4MZ39

• Extreme care should be taken NOT to scratch the bubble dome surface while

installing or adjusting the camera.

• Care should be taken so the cable is NOT damaged, kinked or exposed to

to hazardous areas.

• Tighten the dome cover fixing screws so that there is NO gap

between the Lens hood and clear bubble to avoid light inflow from IR LEDs.

CAUTION

Limit of pan & tilt

1) Pan limit:

Pan is limited to +/- 173°.

Do NOT force the gimbal over the limit to prevent internal damage.

2) Tilt limit:

Tilt is limited to 25° min ~ 90° max. with reference to the ceiling when the

rotation of camera module is 0°, that is, the image is aligned horizontally.

3) Rotation limit (Horizontal image alignment):

Rotation is limited to +/-95° max.

25º

90º

ROTATION

+/- 95°

PAN

+/- 173°

TILT

25°~90°

*** POWER SUPPLY INSTALLATION INSTRUCTIONS CONTINUED ON PG 21

14 15

Operating Instructions - VTD-VD4MZ39

Using OSD Control Controller

The setup menu can be accessed and controlled by the OSD control joy stick

inside the camera unit. Five commands are available with the joy stick.

The design of OSD may differ according to the Model.

1) SET (

) : Access to the menu or enter the setting.

To enter the main menu, press the Set Key down.

2) UP/DOWN ( ) : Choose the desired sub-menu and move the

cursor up or down.

3) LEFT/RIGHT ( : Set up the value of the selected menu. Used to

adjust the desired menu selection and to move the cursor left or right.

Description of the OSD control operation

4) ‘denotes pressing straight down for 2 seconds

Description of the Motorized ZOOM&FOCUS* adjustment

1) : Zoom In

2)

3) : Focus Near

4)

(*) Works only when OSD Menu is inactive.

OSD Control

Joy Stick

Video sub-out Connector

Video Format

DIP Switch

EX-SDI HD-SDI: The default setting is HD-SDI mode.

Using Video format DIP switch

15

Composition - VTC-IR4MZ39

Dimensions

unit : inches (mm)

Video Sub-out

Cable (1pc)

Mounting

Template

Operating

Instruction

Camera

Easy

Bracket

Plastic Anchor:

.24 x 1.18” (6 x 30mm) (4pcs)

L

4.35 (110.5)

3.53 (89.60)

4.37 (111)

3.94 (100)

3.31 (84)

3.39 (86)

3.15 (80)

10.11 (256.70)

Torque Wrench:

.12” (3mm) (1pc)

Mounting Screw:

.16 x 1.18” (4 x 30mm) (4pcs)

Assembly Screw:

.16 x .55” (4 x 14mm) (3pcs)

16 17

Part Names - VTC-IR4MZ39

Adjustment of viewing angle with a bracket

• Extreme care should be taken NOT to

scratch the window in front of lens.

• Care should be taken so the cable is NOT

damaged, kinked or exposed to

hazardous areas.

• Do not expose the camera directly to

a strong light source such as the sun

or spotlights.

CAUTION

Power & video cable

through the rear mount

and connect to the

proper source

Sunshield

Sunshield Bolt

Easy

Bracket

OSD Setup

Control Cover

Bracket

Lock/Unlock

Screw

Torque

wrench

Lock/Unlock

Screw

17

Installation Instructions - VTC-IR4MZ39

1. Locate the mounting template at the installation position and drill the ceiling or

wall if needed. ( *The easy bracket can not be installed on the ceiling)

2. Place the easy bracket on pre-drilled position and attach it through using mounting

screws (

.16 x 1.18” / 4 x 30mm) . Skip this step when an easy bracket is not installed.

3. Route the Power cable to the connecting place.

Hook up the camera bracket with the easy bracket as illustrated below.

4. Attach the camera bracket through using assembly screws (.16 x .59” / 4x15mm).

5. Set the camera’s viewing angle.

6. Put the sunshield on the camera unit and tighten the sunshield-bolts.

Mounting Screw

:

.16 x 1.18” (4 x 30mm)

Plastic Anchor

:

.24 x 1.18” (6 x 30mm)

1

2

Torque Wrench

REAR VIEW

3

Cable exit

4

Assembly Screw

:

.16 x .55” (4 x 14mm)

18 19

Installation Instructions - VTC-IR4MZ39

Pan & Tilt adjustments

1) Pan limit:

Pan is limited to +/- 90°.

3) Inclination limit

(Horizontal image alignment):

Inclination limited to +/-90° max.

2) Tilt limit:

Tilt is limited to 0°(2°) min ~ 90° max.

for wall(ceiling) installation respectively

with reference to the wall(ceiling) when

the inclination of camera module is 0°,

that is, the image is aligned horizontally.

90° 90°

• Unlock the screw on the camera bracket using the torque wrench supplied

• Set the camera’s viewing angle then lock the screw on the bracket.

88°90°

±90°

• on the ceiling • on the wall

19

Operating Instructions - VTC-IR4MZ39

Setup menu can be accessed and controlled by OSD control joystick on

the side of camera unit. Five commands are available with the joystick.

The design of OSD could differ depending on the model.

Description of joystick operation

2) UP/DOWN ( ) : Choose the desired sub-menu and move the cursor up or down.

3) LEFT/RIGHT ( : Set up the value of the selected menu.

Used to adjust the desired menu selection and to move the cursor left or right.

Using OSD controller

4) ‘denotes pressing straight down for 2 seconds

Video Sub-out

Connector

OSD Control Joy Stick

SUB-OUT

ZOOM

Cover Open

Description of the Motorized ZOOM&FOCUS* adjustment

1)

: Zoom In

2)

3) : Focus Near

4)

(*) Works only when OSD Menu is inactive.

ANALOG OUT should be set to TVI MODE, AHD MODE or CVI MODE

to get CVBS video in sub-out. If it is set to CVBS, there is no CVBS video

in sub-out port. (SYSTEM> OUTPUT> ANALOG OUTPUT)

If CVBS video is enabled through ANALOG OUT or Sub-out port, WDR

and 3D-NR functions are disabled in all video outputs.

This should be considered when installer adjusts the video with installation

monitor via CVBS video signal.

20 21

Page is loading ...

Vitek VTC-IR4MZ39 User manual

This manual is also suitable for

Vitek VTC-IR4MZ39 User manual

Related papers

Other documents