SDX230DX

Brother SDX230DX Reference guide

  • Hello! I am an AI chatbot trained to assist you with the Brother SDX230DX Reference guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
EN
Quick Reference Guide
Be sure to rst read the “Important Safety Instructions” in the Product Safety Guide.
This Quick Reference Guide contains basic instructions and information for your Brother machine.
Store this Quick Reference Guide in a safe place, where it can be easily accessed for future reference.
Refer to the Operation Manual for detailed instructions.
The Operation Manual as well as other instructions can be downloaded
from the Brother Solutions Center (http://s.brother/cmoae/).
'/<
Mat (for ScanNCut DX)
* When cutting paper with
a smooth surface
Sheet for fabric cutting Auto blade holder
Standard Tack
Adhesive Mat
Low Tack
Adhesive Mat
Iron-on Fabric
Appliqué Contact
Sheet
(White Backing)
High Tack
Adhesive Fabric
Support Sheet
Auto Blade
(Black)
Thin Fabric Auto
Blade (Beige)
Material Thichkness
Paper
Printer paper 80 g/m² (0.1 mm)
X
Scrapbook paper (thin) 120 g/m² (0.15 mm)
Scrapbook paper (medium-thick)
200 g/m² (0.25 mm)
*
Cardstock 280 g/m² (0.35 mm)
*
Vellum, tracing paper 0.07 mm
Poster board 400 g/m² (0.5 mm)
Fabric
Thin cotton fabric (for quilt piece) 0.25 mm
*1
*1
Thin cotton fabric (except for quilt piece) 0.25 mm
Flannel (for quilt piece) 0.5 mm
*1
*1
Flannel (except for quilt piece) 0.5 mm
Felt 3 mm
Denim 14 oz 0.75 mm
Others
Plastic sheet (PP) 0.2 mm
Vinyl 0.2 mm
*2
Magnet 0.3 mm
Sticker or seal 0.2 mm
Foam sheet 3 mm
Attach the Material to the Mat
Install the Holder
Select the Pattern
Note
Craft paper or fabric covered with decorative layer (that can easily separate) such as lamé or foil is not recommended for use. If such media is used or tested
it is recommended to clean the scanner glass inside the machine after every use.
Make sure that the arrow
is facing the machine
feeder (top side up).
Remove the
protective cap.
Select “Pattern”.
Peel off the protective
sheet.
*Keep the protective sheet for
storage use.
Turn on the machine.Connect the power
cord to the machine,
and then open the
front tray cover.
Pull out the rear tray.
Select your choice of
pattern category.
Before attaching your choice
of material onto the mat, check
if the strength of the adhesive
is suitable by test attaching the
material onto the edge of the
adhesive side of the mat.
Select your choice of
pattern.
If the adhesive is ok,
attach the material onto
the mat’s adhesive.
Hold the blade holder
and then install it in the
carriage with the Brother
Logo facing you.
Check the pattern size and
number of pattern(s), and
then touch the “Set” key.
Apply some pressure to
rmly attach the material
onto the mat.
Press down the
holder lock lever.
Check the pattern(s)
placement, and then
touch the “OK” key.
STEP 2
STEP 3
STEP 4
Mat and Blade Selection
STEP 1
3
3
1
3
1
2
21
2
4
4
4
5
5
5
Prepare the material to be cut. Referring to the following table,
select a mat and blade appropriate
for the material.
1 2
Memo
An auto blade holder is included with this machine. Using the auto blade
holder, the thickness of the material is detected, and the blade extension
automatically adjusts based on the material’s thickness.
Use the mat designed specically for ScanNCut DX.
Depending on your machine model, some accessories may not be
included. Additional purchase may be required.
Load the Mat and Start Cutting
Load the mat (arrow
facing up).
Touch the “Start” key to
start cutting.
When cutting is nished,
touch the “OK” key on
the screen.
Press the “Feed” button
in the operation panel to
release the mat.
Touch “Please select” key then select “Cut” in the
preview screen.
Peel off the material. Use the spatula to peel off
the cutout pattern.
*After using a mat, cover it with the protective sheet.
STEP 5
421
5 76 8
Note
We recommend performing “Test/Trial Cut” before cutting your project. Please refer to “Test/Trial Cut (For Desired Cutting Results)” on the next page.
IMPORTANT
3
For smooth feeding, align the
top of the mat with the guides
on the right and left sides
of the feed slot and insert it
under the feed rollers.
Lightly place your hand on
the center of the mat and
gently push it forward while
pressing the “Feed” button
on the operation panel.
*1: Fabric Mat (CADXMATF12) can be used instead of the Standard Tack Adhesive Mat and the High Tack Adhesive Fabric Support Sheet.
*2: Vinyl Auto Blade Holder included in Vinyl Auto Blade Kit (CADXVBKIT1) and Disney Vinyl Auto Blade Kit (CADXVBDSNKIT1) is also recommended.
Fabric Cutting Basics
Iron-On Fabric Appliqué Contact Sheet
Reinforces the fabric so that various patterns can be cut out.
Original texture may change because it remains attached to the back of the fabric.
*
Use the standard mat. Do not place fabric with an iron-on fabric appliqué contact sheet
attached to the back directly onto a mat with a high tack adhesive fabric support sheet
attached.
High Tack Adhesive Fabric Support Sheet
By attaching this adhesive sheet to the standard mat, the adhesive strength of the mat will
increase.
Cut results may vary depending on the shape of the selected pattern.
Fabric Mat
With this mat, High Tack Adhesive Fabric Support Sheet is not required.
Refer to the “Mat and Blade Selection” table, and
use an iron-on fabric appliqué contact sheet, a
high tack adhesive fabric support sheet or fabric
mat to cut fabric. Refer to the instructions included
with the iron-on fabric appliqué contact sheet, high
tack adhesive fabric support sheet or fabric mat
for details. If these accessories are not included
with your machine, purchase the optional iron-on
fabric appliqué contact sheet (CASTBL1), high tack
adhesive fabric support sheet (CASTBL2) or fabric
mat (CADXMATF12). Some optional accessories
may not be available in other countries.
Direct Cut (Scan and Cut Material’s Pattern(s))
Select “Scan”.
Touch “Please select” key then select “Cut” in the preview
screen.
Peel off the material.
Select “Direct Cut”. Select the destination for
the cutting data.
Use the spatula to peel
off the cutout pattern.
Touch
key to specify
the scan settings.
Touch the “Start” key to
start cutting.
When cutting is nished,
touch the “OK” key.
Touch
to move the test
pattern in a different location.
Touch the “Start” key to start
test/trial cutting.
Touch to adjust the cutting
pressure.
Referring to the “Test/Trial Cut”
Result table below, adjust the
cutting pressure according to
the cutting results, and then
touch the “OK” key.
Attach the original
(stamped paper, printed
paper/sticker, etc.) to the
mat.
After selecting the area to be
cut out, touch the “Preview”
key and then “OK” key.
Press the “Feed” button
in the operation panel to
release the mat.
Touch the “OK” key.
4
9
13
1
1
1211
15
2
2 3
87
3
5
10
14
6
Direct Cut
An original illustration can be scanned and its outline can be cut out.
Scan to Cutting Data
An original illustration can be scanned,
converted to cutting lines for cutting/
drawing with this machine, then saved
as data.
*
Refer to the Operation Manual for
detailed instructions.
Scanning Functions
Scan an illustration, photo or your own drawing to create personalized cut designs. The design can then be cut out or saved as data.
Before working on your actual project, using your choice of material we recommend that you test cut or test the pen/ink (for draw function) to make sure
that you’ll get the desired results. If you achieved your desired results, continue with your project using the same materials you tested.
Getting More Out of ScanNCut
The following website provides methods for getting more out of your ScanNCut using CanvasWorkspace
application, procedures for customizing pattern data, and much more.
After selecting “Cut” in the
preview screen, touch the “Test”
key.
The test pattern will appear at
the bottom right.
Make sure that the test pattern
does not overlap the pattern
for your project. To change
the test pattern location,
touch .
After making the desired
changes, touch the “OK” key.
Touch the “Start” key to start
test/trial cutting.
5
6
8
7
“Test/Trial Cut” Result Adjustment Operation
Part of the material is
not cut.
Pressure too light: Touch
in the
settings screen once to increase the
pressure.
The entire pattern is
not cut.
Pressure too light: Touch in the
settings screen once to increase the
pressure.
There are cutting lines
completely through
the mat.
Pressure too strong: Touch
in the
settings screen once to decrease the
pressure.
Touch the “Test again” key.When “Test/Trial Cut” is done,
without feeding out the mat,
peel off the cutout and check
the “Test/Trial Cut” results.
If the result of the “Test/Trial Cut” is
good (clean and no-fray) continue
cutting your project by touching the
“Start” key on the screen.
If the result of the “Test/Trial
Cut” is good (clean and no-fray)
continue cutting your project by
touching the “Start” key on the
screen.
If you are not satised with the “Test/
Trial Cut” result, follow the pressure
settings procedure from
5
, and
perform “Test/Trial Cut(s)” until you
have the best result.
If the material could not be cut
cleanly, return to step
5
and
perform “Test/Trial Cut” again.
Test/Trial Cut (For Desired Cutting Results)
4
http://CanvasWorkspace.Brother.com
Touch the “Start” key to start
scanning.
Touch the “OK” key.For smooth feeding, align the
top of the mat with the guides
on the right and left sides of the
feed slot and insert it under the
feed rollers.
Lightly place your hand on the
center of the mat and gently
push it forward while pressing
the “Feed” button on the
operation panel.
1/2