2. Sargent
  3. PEX Clamp Pincer Tools 9253 SCP 9252 SCP

Sargent PEX Clamp Pincer Tools 9253 SCP 9252 SCP Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the Sargent PEX Clamp Pincer Tools 9253 SCP 9252 SCP Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Pincer Tools for Oetiker StepLess
®
Ear Clamps 167 for PEX
Basic instructions
Recommended installation
The products may only be used for the intended purpose and under safe and fault-free conditions.
• Correctusagealsocoversobservanceofthisinstructionmanual.
• Anyusenotinaccordancewiththeprescribedusageshallberegardedasincorrectusage,andmayleadto
product failure.
• ForproperinstallationofOetikerPEXseriesclamps,usecalibratedgenuineOetikerinstallationtools.
• Forratchetpincermaintenance,careandcalibration,referencethecompleteCalibrationProceduressupplied
with Tool or reference sections 3.1, 3.2 and 3.3 of this instruction manual.
1. 3-Handle Ratchet Pincer (Fig. 1)
Sargent Tools #9253 SCP
• IncludesGO/NO-GOgauge
• Canbecalibrated
• Lightweightforeasyhandling
• Heavy-dutyprofessionalgradetool
• Singlehandedinstallation
2. 2-Handle Ratchet Pincer (Fig. 2)
Sargent Tools #9252 SCP
• IncludesGO/NO-GOGauge
• Canbecalibrated
• Lightweightforeasyhandling
• Heavy-dutyprofessionalgradetool
l
Fig. 1: 9253 SCP
Fig. 2: 9252 SCP
Page 1
Pincer Tools for Oetiker StepLess
®
Ear Clamps 167 for PEX
Clamp instal
lation instructions
1. PerASTMF2098,insertttingintotubinguntil
shoulder or tube stop contacts end of tubing.
Positionclampwithin1/8“to1/4“(3.2to6.4mm)
of tube end. (Fig. 3
)
2. Close clamp ear with tool, tool will not release
untilclampisfullyclosed.(Fig.4
)
3. IMPORTANT:ForproperinstallationofOetikerPEX
series clamps, full ear closure is required. Visually
inspect clamp for correct closed ear form. (Fig. 5
)
Fig. 3: Insert itting/position clamp
Fig. 4: Close clamp ear with tool
Fig. 5: Full ear closure required
Page 2
Pincer Tools for Oetiker StepLess
®
Ear Clamps 167 for PEX
Assembly notice
Warning notice: clamp installations
Inte
rnational standards
• ClampsconformtoASTM
1
F2098forusewithASTMF1807andF2159insertttingsand
ASTM F876 PEX
2
tubing. For additional information, please refer to ASTM International Standards Worldwide.
• ComplieswithNSF
3
productlistingcNSFus-PW.Foradditionalinformation,pleaserefertothe
NSForganization.
1
ASTM = American Society for Testing and Materials
2
PEX = Polyethylene cross-linked
3
NSF=NationalSanitationFoundation
NOTICE
For the correct assembly of Oetiker StepLess
®
167 PEX clamps, the clamps must be completely closed.
GenuineOetikerHandInstallationPincerswithratchetmechanismwillreleaseonlywhenclamphasfullyclosed.
WARNING
Inhighchloridewaterconditions,useonlyplasticttings.
Do not install in contact with concrete
UseonlyASTMF1807orF2159insertttingswithOETIKERclamps.
Failure to observe the above warnings may result in property damage.
Page 3
Pincer Tools for Oetiker StepLess
®
Ear Clamps 167 for PEX
1. Using a straight blade screw driver, loosen
adjustment nut (Fig. 11).
2. ClosehandlestostoppointandplaceGO/NO-GO
Gauge into jaw gap.
3. Using a straight blade screwdriver, rotate eccentric
stud (Fig. 12) counter-clockwise until jaws contact
theGO/NO-GOGaugebeforetheNO-GOareaof
the Gauge.
4. Using a straight blade screwdriver, tighten the
adjustment nut (Fig. 13).
5. Checktoolcalibrationdaily.
Tool maintenance
• DonotusetheRatchetToolsforanypurposeotherthantoassembleclamps.Useotherthanintendedmay
damage the tool and void warranty.
• Lubricatethetoolhead,springandratchetmechanismonceperevery30dayswithalightlubricatingoil(iftool
operation becomes sluggish at any time lubricate prior to further use).
• Cleantoolperiodicallytoremoverustanddirt.Rustordirtbuild-upwillinterferewithtooloperationandvoid
warranty coverage. Lubricate all parts after cleaning to provide a light protective coating of oil.
Tool warranty
When properly maintained and used as intended the Ratchet Tools are warranted against materials and manufacturing
defects for a period of one year from date of purchase. This warranty does not cover defects or damage arising from
improperstorageorhandling,ordinarywearandtear,misuse,abuse,accidentorusewithunauthorizedproductor
parts. Liability is limited to repair or replacement of product or component part which is determined defective as covered by
this warranty.
Fig. 11: Adjustment nut
Fig. 12: Eccentric Stud
Fig. 13: Adjustment nut
Re-calibrating tools for: Tools nos. 9253 SCP and 9252 SCP
Re-calibrationinstructionsonthispagearespecificforRatchetPincerTool nos. 9253 SCP and 9252 SCP
11
12
13
Page 4
/