HP D6000 User manual

Brand: HP

Model: D6000

Category: Disk arrays

Type: User manual

HP D6000 Disk Enclosure

User Guide

Abstract

This guide describes identification, operations, setup, configuration and utilities, troubleshooting, regulatory notices, specifications, and technical

support. This guide is for an ex

perienced service technician. HP assumes that you are qualified in the servicing of computer equipment, trained in

recognizing hazards in products and are familiar with weight and stability precautions.

Part Number: 682254-001

September 2012

Edition: 1

The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express

warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall

not be liable for technical or editorial errors or omissions contained herein.

Bluetooth® is a trademark owned by its proprietor and used by Hewlett-Packard Company under license.

Microsoft® and Windows® are U.S. registered trademarks of Microsoft Corporation.

Contents 3

Contents

Component identification ............................................................................................................... 5

Front panel components ............................................................................................................................. 5

Front panel LEDs and buttons ...................................................................................................................... 6

Rear panel components .............................................................................................................................. 7

Rear panel LEDs and buttons ....................................................................................................................... 8

Device bay ID numbers ............................................................................................................................ 10

Hard drive LEDs ...................................................................................................................................... 10

Hard drive LED combinations .................................................................................................................... 11

Operations ................................................................................................................................. 12

Firmware update ..................................................................................................................................... 12

Powering up ........................................................................................................................................... 12

Power down ........................................................................................................................................... 13

Setup ......................................................................................................................................... 14

Space and airflow requirements ................................................................................................................ 14

Temperature requirements ........................................................................................................................ 14

Power requirements ................................................................................................................................. 15

Electrical grounding requirements .............................................................................................................. 15

Rack warnings ........................................................................................................................................ 16

Third-party racks ..................................................................................................................................... 16

Site planning considerations ..................................................................................................................... 16

Installing the enclosure ............................................................................................................................. 16

Installing the hard drives .......................................................................................................................... 18

Installing optional I/O modules ................................................................................................................. 21

Cabling the D6000 ................................................................................................................................. 23

Mini-SAS I/O cables ...................................................................................................................... 23

Power cords .................................................................................................................................. 23

Configuration and utilities ............................................................................................................ 24

Configuration tools .................................................................................................................................. 24

Array Configuration Utility .............................................................................................................. 24

Option ROM Configuration for Arrays ............................................................................................. 24

Smart Components for ROM Flash ................................................................................................... 25

Management tools ................................................................................................................................... 25

HP Systems Insight Manager ........................................................................................................... 25

Management Agents ...................................................................................................................... 25

Diagnostic tools ...................................................................................................................................... 25

Integrated Management Log ........................................................................................................... 25

Array Diagnostic Utility .................................................................................................................. 26

Remote support and analysis tools ............................................................................................................. 26

HP Insight Remote Support software ................................................................................................. 26

Keeping the system current ....................................................................................................................... 27

Change control and proactive notification ........................................................................................ 27

Care Pack .................................................................................................................................... 27

Troubleshooting

.......................................................................................................................... 28

When the D6000 does not power up ........................................................................................................ 28

Contents 4

LED behavior .......................................................................................................................................... 28

7-segment display status codes and actions....................................................................................... 29

Recognizing hard drive failure .................................................................................................................. 30

Effects of a hard drive failure .......................................................................................................... 31

Compromised fault tolerance .......................................................................................................... 31

Recovering from compromised fault tolerance .................................................................................... 31

Factors to consider before replacing hard drives ......................................................................................... 32

Automatic data recovery (rebuild) .............................................................................................................. 32

Time required for a rebuild ............................................................................................................. 33

Failure of another drive during rebuild ............................................................................................. 33

Regulatory compliance notices ..................................................................................................... 34

Regulatory compliance identification numbers ............................................................................................. 34

Federal Communications Commission notice ............................................................................................... 34

FCC rating label ............................................................................................................................ 34

Class A equipment......................................................................................................................... 34

FCC Notice, Class B Equipment ...................................................................................................... 35

Declaration of conformity for products marked with the FCC logo, United States only ....................................... 35

Modifications .......................................................................................................................................... 36

Cables ................................................................................................................................................... 36

Canadian notice (Avis Canadien) .............................................................................................................. 36

European Union regulatory notice ............................................................................................................. 36

Disposal of waste equipment by users in private households in the European Union ......................................... 37

Japanese notice ...................................................................................................................................... 38

BSMI notice ............................................................................................................................................ 38

Korean notice ......................................................................................................................................... 38

Chinese notice ........................................................................................................................................ 39

Vietnam compliance marking notice .......................................................................................................... 39

Ukraine notice ........................................................................................................................................ 39

Power cord statement for Japan ................................................................................................................. 39

Electrostatic discharge ................................................................................................................. 40

Preventing electrostatic discharge .............................................................................................................. 40

Grounding methods to prevent electrostatic discharge .................................................................................. 40

Specifications ............................................................................................................................. 41

Environmental specifications ..................................................................................................................... 41

Storage array specifications ..................................................................................................................... 41

Support and other resources ........................................................................................................ 42

Before you contact HP .............................................................................................................................. 42

HP contact information ............................................................................................................................. 42

Customer Self Repair ............................................................................................................................... 42

Acronyms and abbreviations ........................................................................................................ 50

Documentation feedback ............................................................................................................. 51

Index ......................................................................................................................................... 52

Component identification 5

Component identification

Front panel components

Item Description

Drawer 1

Drawer 1 diagnostic cable access (For use by authorized

HP personnel only)

Drawer 2

Drawer 2 diagnostic cable access (For use by authorized

HP personnel only)

Component identification 6

Front panel LEDs and buttons

Item Description Status

Hard drive LEDs

Normal mode

(UID LED is solid)

Green = The drive is online, but is not

currently active.

Flashing irregularly green = The drive is

active and it is operating normally.

Flashing green (1 Hz) = Do not remove

the drive. Removing the drive may

terminate the current operation and

cause data loss. The drive is rebuilding,

or it is part of an array that is undergoing

expansion, logical drive extension, a

stripe size migration, or RAID migration.

Flashing amber/green = Drive is

configured and indicating a predictive

failure. The drive may also be

undergoing a rebuild, expansion,

extension, or migration.

Flashing amber (1 Hz) = A predictive

failure alert has been received for this

drive. Replace the drive as soon as

possible.

Amber = Drive failure, link failure, or

mismatched configuration.

Off = The drive is offline, a spare, or not

configured as part of an array.

Component identification 7

Item Description Status

Hard drive LEDs

Drive locate mode

(UID LED is flashing)

Green = The drive has been selected by

a management application and it is

operating normally.

Flashing amber (1 Hz) = The drive is not

selected and is indicating a predictive

failure.

Flashing amber/green = The drive has

been selected by a management

application and is indicating a

predictive failure.

Amber = The drive might or might not be

selected and is indicating drive failure,

link failure, or mismatched

configuration.

Off = The drive is not selected.

UID button/LED Blue = UID LED is enabled from the UID

button

Blue flashing = Item 1 is in locate mode

Off = UID LED is disabled

Internal Health LED Green = System health is good

Off = System is off

GSI LED Amber = Enclosure requires service

check: I/O, fan and power supply LEDs,

and AC power cables to power supplies.

Off = Enclosure is functioning normally.

Rear panel components

The figure shows a maximum configuration. Your enclosure might appear differently, for example,

containing power supply or I/O module blanks, depending on the configuration that was ordered.

Item Description

Power supply 1

Component identification 8

Item Description

Power On/UID 2 status panel

Fan module 1 (Drawer 2)

Primary I/O module (Drawer 2)

SAS port 1 connector

SAS port 2 connector

Power supply 3

UID 1 status panel

Fan module 1 (Drawer 1)

Primary I/O module (Drawer 1)

SAS port 1 connector

SAS port 2 connector

SAS port 1 connector

SAS port 2 connector

Secondary I/O module (Drawer 1)

Fan module 2 (Drawer 1)

Power supply 4

SAS port 1 connector

SAS port 2 connector

Secondary I/O module (Drawer 2)

Fan module 2 (Drawer 2)

Power supply 2

Rear panel LEDs and buttons

Item Description Status

Power On/Standby button

and system power LED

Green = On

Amber = Standby (auxiliary power

present)

Off = Off

Component identification 9

Item Description Status

Internal Health LED Green = System health is good.

Off = System is off.

GSI LED* Amber = Enclosure requires service

check: I/O, fan and power supply LEDs,

and AC power cables to power supplies.

Off = Enclosure is functioning normally.

UID button/LED (Drawer 2) Blue = UID LED is enabled from the UID

button.

Blue flashing = System is in hard drive

locate mode or an enclosure firmware

update is in progress.

Off = UID LED is disabled.

Power supply LED Green = Power on and power supply

functioning properly

Off = One or more of the following

conditions exists:

•

System powered off

•

AC power unavailable

•

Power supply failed

•

Power supply exceeded current limit

System fan LED Green = Normal operation

Amber flashing = Fault

Off = Fan unseated from connector or

failed

I/O module LED Green = System activity

Amber = Fault

Off = Enclosure is powered off.

7-segment display* 1 = SES overall warning

2 = Temperature sensor warning

3 = Cooling fan warning

4 = Power supply warning

5 = Host GSI enabled

6 = I/O PIC upgrade needed

7 = Power supply PIC upgrade needed

8 = CPLD upgrade needed

9 = Standby heartbeat failure

10 = Remote I/O module heartbeat

failure

11 = Enclosure thermal shutdown

imminent

12 = Enclosure thermal shutdown

occurred

13 = Enclosure management bus failure,

false fan failures may occur

14 = Signal integrity errors detected

15 = Power supply PIC communications

error

16 = Unsupported backplane detected

UID button/LED (Drawer 1) Blue = UID LED is enabled from the UID

button.

Blue flashing = System is in hard drive

locate mode or an enclosure firmware

update is in progress.

Component identification 10

Item Description Status

Off = UID LED is disabled.

* If the GSI is amber, the system needs service. Activate the associated drawer UID button to view any GSI error codes

on the rear display.

Device bay ID numbers

Hard drive LEDs

Item Description

Fault/UID LED (amber/blue)

Online LED (green)

Component identification 11

Hard drive LED combinations

Online/activity

LED (green)

Fault/UID LED

(amber/blue)

Interpretation

On, off, or flashing

Alternating amber

and blue

The drive has failed, or a predictive failure alert has been received

for this drive; it also has been selected by a management

application.

On, off, or flashing

Steadily blue The drive is operating normally, and it has been selected by a

management application.

Amber, flashing

regularly (1 Hz)

A predictive failure alert has been received for this drive.

Replace the drive as soon as possible.

Off The drive is online, but it is not currently active.

Flashing regularly

(1 Hz)

Amber, flashing

regularly (1 Hz)

Do not remove the drive. Removing a drive may terminate the

current operation and cause data loss.

The drive is part of an array that is undergoing capacity expansion

or a stripe size migration, but a predictive failure alert has been

received for this drive. To minimize the risk of data loss, do not

replace the drive until the expansion or migration is complete.

Flashing regularly

(1 Hz)

Off Do not remove the drive. Removing a drive may terminate the

current operation and cause data loss.

The drive is rebuilding, or it is part of an array that is undergoing

array expansion, logical drive extension, a stripe size migration,

or RAID migration.

Flashing irregularly

Amber, flashing

regularly (1 Hz)

The drive is active, but a predictive failure alert has been received

for this drive. Replace the drive as soon as possible.

Flashing irregularly

Off The drive is active and it is operating normally.

Off

Steadily amber A critical fault condition has been identified for this drive and the

controller has placed it offline. Replace the drive as soon as

possible.

Off

Amber, flashing

regularly (1 Hz)

A predictive failure alert has been received for this drive. Replace

the drive as soon as possible.

Off

Off The drive is offline, a spare, or not configured as part of an array.

Operations 12

Operations

Important Safety Information

Before installing this product, read the Important Safety Information document provided.

Firmware update

Before configuring and using the D6000, be sure that the D6000 and all other devices in the SAS fabric are

running the latest compatible versions of firmware.

The D6000 can be installed in a variety of deployments, each of which uses an updating method specific to

the deployment:

• If the D6000 is directly connected to a Smart Array controller installed in a rack-mounted server, update

the D6000 firmware using a downloaded Smart Component. For more information about Smart

Components, see Smart Components for ROM Flash.

• If the D6000 is connected to a SAS BL Switch as part of a BladeSystem solution, update the D6000

firmware using downloaded firmware image files and the HP 6G Virtual SAS Manager software

embedded in the SAS BL Switch. For more information about updating firmware using the HP 6G Virtual

SAS Manager, see the HP 6G Virtual SAS Manager User Guide, available on the 6Gb SAS BL Switch

website HP website (http://www.hp.com/go/6gbsasbl).

• If the D6000 is connected to a SAS BL Switch as part of an HP IBRIX X9000 solution, update the D6000

firmware using the solution's Firmware Management Tool. For more information about these

environments, see the user documents on HP website (http://www.hp.com/go/x9000). (The HP IBRIX

X9000 solution family will be rebranded in late 2012. At that time, product and deliverable names will

be updated to include the new branding.)

The new D6000 firmware activates only after the D6000 is reset from a software tool or manually power

cycled.

Powering up

Observe the following guidelines before powering up the D6000:

• Always install all components of the D6000.

• Install hard drives in the D6000 so the connected host controllers can identify and configure them at

power up.

• Always power up the D6000 first, and then the server.

To power up the D6000:

1. Complete server hardware installation and cabling. For more information, see the server

documentation.

2. Connect the SAS cables and power cords to the D6000.

Operations 13

Press and hold the Power On/Standby button.

Wait and observe the system power LED and system fans. When the D6000 powers up, the system

power LED illuminates solid green and the system fans spin to a high speed, and then spin down to a

low speed.

4. Power up the servers. For more information, see the server documentation.

Power down

Be sure that the partner servers are the first units to be powered down and the last to be powered back up.

Taking this precaution ensures that the system and the OS are shut down in an orderly manner.

IMPORTANT: If installing a hot-plug device, it is not necessary to power down the D6000.

To power down the D6000:

1. Power down the partner servers. See the server documentation.

2. Press and hold the Power On/Standby button for approximately 4 seconds. This action powers down

both hard drive drawers.

Setup 14

Setup

Space and airflow requirements

To allow for servicing and adequate airflow, observe the following space and airflow requirements when

deciding where to install a rack:

• Leave a minimum clearance of 63.5 cm (25.0 in) in front of the rack.

• Leave a minimum clearance of 76.2 cm (30.0 in) behind the rack.

• Leave a minimum clearance of 121.9 cm (48.0 in) from the back of the rack to the back of another rack

or row of racks.

The HP D6000 draws in cool air through the front door, and then expels warm air through the rear door.

Therefore, the front and rear rack doors must be ventilated adequately to enable ambient room air to enter

the cabinet, and the rear door must be ventilated adequately to enable the warm air to escape from the

cabinet.

CAUTION: To prevent improper cooling and damage to the equipment, do not block the

ventilation openings.

When a vertical space in the rack is not populated by a server or rack component, the gaps between the

components cause changes in airflow through the rack and across the servers. Cover all gaps with blanking

panels to maintain proper airflow.

CAUTION: Always use blanking panels to fill empty vertical spaces in the rack. This arrangement

ensures proper airflow. Using a rack without blanking panels results in improper cooling that can

lead to thermal damage.

The HP Rack 10000 series rack provides proper server cooling from flow-through perforations in the front

and rear doors that provide a 64-percent open area for ventilation.

CAUTION: HP has not tested or validated the D6000 with third-party racks. If a third-party rack

is used, observe the following additional requirements to ensure adequate airflow and to prevent

damage to the equipment:

• Front and rear doors—If the 42U rack includes closing front and rear doors, you must allow at

least 5,350 sq cm (830 sq in) of holes evenly distributed from top to bottom to permit adequate

airflow (equivalent to the required 64-percent open area for ventilation).

• Side—The clearance between the installed rack component and the side panels of the rack

must be a minimum of 7 cm (2.75 in).

Temperature requirements

To ensure continued safe and reliable equipment operation, install or position the D6000 in a well-ventilated,

climate-controlled environment.

The maximum TMRA for most storage products is 35°C (95°F). The temperature in the cold aisle where the

rack is located must not exceed 35°C (95°F). The D6000 reports an over-temperature condition and

Setup 15

performs an emergency shutdown of the hard drive bays within a drawer if the temperature exceeds this limit

for greater than 3 minutes. To recover the system, AC power cycle the D6000.

CAUTION: To reduce the risk of damage to the equipment when installing third-party options:

• Do not permit optional equipment to impede airflow around the D6000 or to increase the

internal rack temperature beyond the maximum allowable limits.

• Do not exceed the manufacturer’s TMRA.

Power requirements

Installation of this equipment must comply with local and regional electrical regulations governing the

installation of IT equipment by licensed electricians. This equipment is designed to operate in installations

covered by NFPA 70, 1999 Edition (National Electric Code) and NFPA-75, 1992 (code for Protection of

Electronic Computer/Data Processing Equipment). For electrical power ratings on options, refer to the

product rating label or the user documentation supplied with that option.

WARNING: To reduce the risk of personal injury, fire, or damage to the equipment, do not

overload the AC supply branch circuit that provides power to the rack. Consult the electrical

authority having jurisdiction over wiring and installation requirements of your facility.

CAUTION: Protect the D6000 from power fluctuations and temporary interruptions with a

regulating UPS. This device protects the hardware from damage caused by power surges and

voltage spikes and keeps the D6000 in operation during a power failure.

When installing more than one D6000, you may need to use additional power distribution devices to safely

provide power to all devices. Observe the following guidelines:

• Balance the D6000 power load between available AC supply branch circuits.

• Do not allow the overall system AC current load to exceed 80 percent of the branch circuit AC current

rating.

• Do not use common power outlet strips for this equipment.

• Provide a separate electrical circuit for each power supply in the D6000.

Electrical grounding requirements

The D6000 must be grounded properly for proper operation and safety. In the United States, you must install

the equipment in accordance with NFPA 70, 1999 Edition (National Electric Code), Article 250, as well as

any local and regional building codes. In Canada, you must install the equipment in accordance with

Canadian Standards Association, CSA C22.1, Canadian Electrical Code. In all other countries, you must

install the equipment in accordance with any regional or national electrical wiring codes, such as the

International Electrotechnical Commission (IEC) Code 364, parts 1 through 7. Furthermore, you must be sure

that all power distribution devices used in the installation, such as branch wiring and receptacles, are listed

or certified grounding-type devices.

Because of the high ground-leakage currents associated with multiple D6000 connected to the same power

source, HP recommends the use of a power distribution unit (PDU) that is either permanently wired to the

building’s branch circuit or includes a nondetachable cord that is wired to an industrial-style plug. NEMA

locking-style plugs or those complying with IEC 60309 are considered suitable for this purpose. Using

common power outlet strips for the D6000 is not recommended.

Setup 16

Rack warnings

WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that:

• The leveling jacks are extended to the floor.

• The full weight of the rack rests on the leveling jacks.

• The stabilizing feet are attached to the rack if it is a single-rack installation.

• The racks are coupled together in multiple-rack installations.

• Only one component is extended at a time. A rack may become unstable if more than one

component is extended for any reason.

WARNING: To reduce the risk of personal injury or equipment damage when unloading a rack:

• At least two people are needed to safely unload the rack from the pallet. An empty 42U rack

can weigh as much as 115 kg (253 lb), can stand more than 2.1 m (7 ft) tall, and might

become unstable when being moved on its casters.

• Never stand in front of the rack when it is rolling down the ramp from the pallet. Always handle

the rack from both sides.

Third-party racks

HP has not tested or validated the D6000 with any third-party racks. Before installing the D6000 in a

third-party rack, be sure to properly scope the limitations of the rack.

Site planning considerations

Customer facility managers and system administrators must discuss site planning, preparation, and system

installation before system delivery. A common understanding of environmental requirements and how the

systems will be delivered, configured, installed, and maintained helps to create a suitable data center and

aids the successful installation of the servers and related equipment.

It is important to plan the facility as a whole, not design based on calculations of individual system or rack

level requirements. Too many interdependencies in a modern data center make such simple calculations

unreliable. Designs and plans must be made for the data center as a whole, including all of its equipment,

with the realization that making one change in the data center environment can affect many other physical,

mechanical, and environmental aspects of the facility.

Take into account the requirements of third-party equipment and support equipment in the room. Dense

computing locations might have high power and cooling demands that could affect power and

environmental constraints. Be aware of rack positioning and airflow patterns. Ensure that the raised floor

space, cooling equipment, power supply equipment and generators, and other support equipment meet the

demands of all the servers and other mission-critical equipment.

Installing the enclosure

WARNING: The D6000 with no drives installed weighs 72.58 kg (160.00 lb). With all drives

and components installed, the enclosure can weigh up to 145.15 kg (320 lb). Before configuring

your rack solution, be sure to check the manufacturer weight limits and specifications. Failure to

do so can result in physical injury or damage to the equipment and the facility.

Setup 17

CAUTION: Always plan the rack installation so that the heaviest item is on the bottom of the rack.

Install the heaviest item first, and continue to populate the rack from the bottom to the top.

CAUTION: HP has not tested or validated the D6000 with any third-party racks. Before installing

the D6000 in a third-party rack, be sure to properly scope the limitations of the rack and consider

the following:

• You must fully understand the static and dynamic load carrying capacity of the rack and be

sure that it can accommodate the weight of the D6000.

• You must install a 1U tray beneath the D6000 to ensure proper support.

• Be sure sufficient clearance exists for cabling, installation and removal of the enclosure,

actuation of the rack doors, and full articulation of the drive drawers.

IMPORTANT: Some racks other than the HP Rack 10000 Series rack do not allow full access to

hard drive bays 29–35 in hard drive drawer 2.

The rack rails are marked for easy identification. The left rack rail is marked "L" and the right rack rail is

marked "R."

To install the rack rails:

1. Begin with the left rack rail. Align the end of the rail with the rear rack column.

2. Slide the rack rail closed until the end of the rail is locked in place, wrapping behind the rear rack

column.

3. Slide the front end of the rail to the rack front column. When fully seated, the rack rail will lock into

place.

4. Repeat the procedure for the right rack rail.

Setup 18

WARNING: The D6000 is very heavy. To reduce the risk of personal injury or damage to the

equipment:

• Observe local occupational health and safety requirements and guidelines for manual

material handling.

• Remove all installed D6000 components from their D6000s before installing or moving the

D6000s.

• Use caution and get help to lift and stabilize D6000s during installation or removal, especially

when the D6000 is not fastened to the rack.

WARNING: Always use at least two people to lift an enclosure into the rack. If the enclosure is

being loaded into the rack above chest level, a third person must assist with aligning the enclosure

with the rails while the other two people support the weight of the enclosure.

5. Install the D6000, making sure to tighten the thumbscrews to secure the D6000 to the rack.

The installation is complete.

Installing the hard drives

A D6000 supports up to 35 hard drives per storage drawer. For weight-distribution purposes and

best-possible cooling, populate hard drive bays from the rear to the front, starting with the highest device bay

ID number ("Device bay ID numbers" on page 10). To properly distribute air flow and cool the installed

drives, make sure that all drive bays are populated with a drive or a drive blank.

Before installing the drives, confirm that they are supported for use in the D6000. For more information, see

the QuickSpecs on the HP website (http://www.hp.com/go/d6000/quickspecs).

When adding hard drives to the hard drive drawer, observe the following general guidelines:

• Verify that the drives are fully seated before closing the drawer.

• The drawer is fully closed when the fans slow down to their normal speed.

• The drawer should be closed with the handle in the released position.

• Hard drives are sensitive to excess vibration. Use care when opening and closing the drawer.

Setup 19

• A RAID 1 mirror requires an even number of hard drives.

• Drives that will be configured within an array should be the same capacity to provide the greatest

storage space efficiency.

NOTE: ACU does not support mixing SAS and SATA drives in the same logical volume.

To install the drives:

1. Be sure all I/O bays contain either an I/O module or an I/O blank. The hard drive drawer does not

open if I/O bays are empty.

2. Be sure the I/O modules or I/O blanks are fully seated and their handles are in the locked position. The

hard drive drawer does not open if I/O modules or I/O blanks are not fully seated with their handles

in the locked position.

WARNING: TIP HAZARD! To reduce the risk of personal injury or damage to the equipment, do

not extend the hard drive drawers beyond the supporting surface when the unit is not installed in

a rack.

WARNING: To reduce the risk of personal injury or damage to the equipment, ensure that only

one hard drive drawer is extended at a time.

3. Extend the hard drive drawer.

WARNING: Pinch hazard—Keep hands out of front and rear of chassis when closing hard drive

drawers.

CAUTION: To prevent improper cooling and thermal damage, do not operate the D6000 for an

extended period of time with the drawer open.

CAUTION: To prevent improper cooling and thermal damage, do not operate the D6000 unless

all bays are populated with either a component or a blank.

Setup 20

Remove the hard drive blank.

5. Prepare the hard drive.

Page is loading ...

HP D6000 User manual

Brand: HP

Model: D6000

Category: Disk arrays

Type: User manual

Download PDF

report

HP D6000 User manual

HP D6000 User manual

Related papers

Other documents