Page is loading ...
344163
TiPolyxMemoryDisplay
User guide
09/10-01 PC
2
TiPolyxMemoryDisplay
User guide
3
Contents
1. Hardware and Software requirements 4
1.1 Hardware requirements 4
1.2 Software requirements 4
2. Installation 4
3. Fundamental concepts 4
3.1 Start screen and pushbuttons/menu for the selection of the functions 5
3.2 Connecting the device to a PC 7
3.3 Download 8
3.4 Upload 9
3.5 Update firmware 10
3.6 Request device info 10
4. Main screen 11
4.1 Project items area 12
4.2 Display area 12
4.3 Property/Project Area 13
5. Project configuration 14
5.1 Home Page 14
5.2 Communication - Available functions and their configuration 16
5.3 Home automation - Available functions and their configuration 18
5.4 Advanced - Available functions and their configuration 22
6. System configuration 24
7. Ringtone configuration 25
7.1 Description of the functions 25
7.2 Creating a ringtone 26
7.3 Linking a ringtone to an event 30
8. Project creation procedure 31
4
1.1 Hardware requirements
• Personal Computer with > 300 MHz Pentium processor minimum.
• 1 GB RAM memory.
• SVGA graphic card with 800x600 resolution.
• CD-ROM reader.
• Mouse.
1.2 Software requirements
• Windows XP 32BIT, Windows Vista 32BIT, or Windows 7.
• Microsoft™ framework.NET 3.5 SP1.
The updated requirements can be found on the www.bticino.com website
1. Hardware
and Software
requirements
To install the TiPolyxMemoryDisplay software proceed as follows:
1. Insert the CD-Rom in the CD drive;
2. Select “Install TiPolyxMemoryDisplay” from the main web screen that will appear;
3. The installation program will start copying the system files needed for the installation of the
TiPolyxMemoryDisplay software.
2. Installation
Warning: The
TiPolyxMemoryDisplay
software is the
fundamental tool for the
configuration of the Polyx
Memory Display 344163,
which, for convenience,
will be referred to as
device in this manual. The
content of this software
is protected by exclusive
rights owned by the
company BTicino SpA.
3. Fundamental
concepts
Warning: For correct
TiPolyxMemoryDisplay
software operation,
the device must be
installed following the
instructions contained
in the instruction leaflet
supplied with the product.
The TiPolyxMemoryDisplay software lets you confi gure the device.
Depending on the installer and user’s needs you can start with a new design or edit an existing one.
In this manual all the examples refer to a “new design”.
To create a new design
• Run TiPolyxMemoryDisplay.
• Make a new design.
• Send the data to the device
To edit an existing design
• Receive the current confi guration data from the device.
• Make any modifi cations.
• Send the data of the design made to the device
With TiPolyxMemoryDisplay you can update the device firmware version (Add fi rmware) with new
revisions issued by Bticino.
TiPolyxMemoryDisplay
User guide
5
3.1 Start screen and pushbuttons/menu for the selection of the functions
After initialising the program the start screen will be displayed. From here the user can:
• Create a new project
• Open an existing project
• Acquire the configuration from the device
• Display the information on the device
• Update the firmware
• Select the language
When creating or opening a project, the main screen appears, from where the user can perform all
the functions explained below.
All the functions that can be performed using TiPolyxMemoryDisplay can be selected by clicking the
icons on the toolbar, or by selecting the appropriate items from the drop down menus.
The toolbar includes the following functions:
Creation, Open and Save configuration file
Upload, Download the configuration
Update device firmware
Request of device information
Selection of the application language
Connection to the www.bticino.com site
6
The pull-down menu has the following options:
• New
Creates a new project
• Open
Opens an existing configuration file
• Save
Saves the current project
• Save as...
Saves the current project asking for a name for the file
• Exit
Exits the program
“File” menu
• Upload
It acquires and displays the current device configuration
• Download
Downloads the configuration to the device
• Update firmware
Updates the device firmware
• Request device info
Enables to display technical information
“Tools” menu
• Language
Can select the application language
“Language” menu
TiPolyxMemoryDisplay
User guide
7
“?” menu
• About...
It displays some TiPolyxMemoryDisplay program information
• Supported version
It displays the list of device firmware versions supported by the program in a table format
3.2 Connecting the device to a PC
To perform the Download configuration, Upload configuration, Firmware Update and Request
device info functions, the user must first connect the device to a PC, and ensure that the correct
port has been selected.
This operation must be performed as follows:
Connect a USB cable to the miniUSB connector of the device and a PC USB port.
To ensure that the communication is successful, the Polyx Memory Display must be connected to
the BUS, and must be powered.
No connection to the Polyx Memory Display is necessary when creating and saving a project.
USB-miniUSB
8
3.3 Download
It allows the user to send the project created to the device.
Procedure:
• Connect the device to a PC as shown in the corresponding section.
• From the Tools pull-down menu select Download.
The following window appears:
• Select Next.
• Select the Serial connection mode and click Next.
• Select the COM port to which the device is connected.
TiPolyxMemoryDisplay
User guide
9
3.4 Upload
It allows the user to receive the configuration from the device; once the configuration has been
acquired, this can be changed and saved, or it can be resent to the device.
Procedure:
• Connect the device to a PC as shown in the corresponding section.
• From the Tools pull-down menu select Upload.
This action will open a mask for the selection of the mode of connection to the device (for the con-
nection procedures see the Download section).
After selecting the connection mode, click “Next” to load the project currently installed on the de-
vice.
• After clicking Next the project is transferred to the device.
Display the
details of the
current download
It exports
the log file
Hide the details
of the current
download
Repeat the operation if unsuccessful
10
3.6 Request device info
It displays some information on the device connected to the PC.
Procedure:
• Connect the device to a PC as shown in the corresponding section.
• From the Tools pull-down menu select Request device info.
This action will open a mask for the selection of the mode of connection to the device (for the con-
nection procedures see the Download section).
After selecting the connection mode, click “Next” to open a screen showing the device hardware
and software features.
3.5 Update firmware
It allows the user to update the device firmware.
Procedure:
• Connect the device to a PC as shown in the corresponding section.
• From the Tools pull-down menu select Update firmware.
The following screen appears, prompting the user to search for the folder containing the firmware
file with extension .fwz (compressed file).
• Select the file and click Open to continue.
This action will open a mask for the selection of the mode of connection to the device (for the con-
nection procedures see the Download section).
TiPolyxMemoryDisplay
User guide
11
Pull-down menus Display
Save file
Remove object
Pushbutton menu
Navigation bar
Project items
Property/Project
4. Main screen
When the application is started, the main screen is displayed. This consists of 3 separate areas:
Project items, Display, and Property/Project.
The top section of the screen shows the menus and pushbuttons used for the management of the
project; The centre section, split into three areas, is where the configuration of the device Home Page is
performed.
Navigation bar
Navigation through the sub-pagesHome
Go to the
previous page
Go to the
next page
Copy
object
Cut object
12
4.1 Project items area
In this area the user can select the objects that will be included in the pages and sub-pages of the
device.
The objects are split into the following categories, based on their functions:
• Communication
• Home automation
• Advanced.
Click the corresponding label to make the category objects available.
4.2 Display area
The Display area shows the future setup of the device Home Page.
This page consists of 6 icons. The f t 5 can be customised. The last one is the Settings icon (which
cannot be customised or removed).
The full list of the available objects and their configurations can be found in the relevant sections,
while the modes of use are described in the Home Page section.
MANI LIBERE
TiPolyxMemoryDisplay
User guide
13
4.3 Property/Project Area
This area is split into two sections, which can be selected by clicking the labels in the bottom area.
The Property section shows the configuration fields for the object currently selected in the Display
area.
The Project section displays the objects by page in a tree menu format. In addition to selecting the
objects, the user can also navigate through the project, selecting any available sub-pages.
Page parameters
Page description
Selected object
parameters
Parameters description
Property/project
selection label
Home Page
Sub-page
14
5. Project
configuration
The configuration of a project may be completed in different ways, for example by creating a totally
new project, and uploading it on the device, or, after acquiring, and if necessary modifying, the
configuration of the device, by saving the project in the PC and exporting it to the device at a later
stage. It is also possible to export a project in .csv format, and then import it in Microsoft Excel ®.
5.1 Home Page
Using the Home Page it is possible to create the device Menu. To do so, drag the objects from the
Project Items area into the Display area, and configure them in the Property/Project Area.
Sub-pages
Some objects are used for connection to other pages, where correlated objects are grouped to-
gether (e.g. Scenarios).
TiPolyxMemoryDisplay
User guide
15
When one of these objects is included in the Home Page, the arrow will be highlighted, to indicate
that a sub-page has been added. Click this arrow to access the new page, where further objects could
also be inserted.
In the tree structure, these objects are marked with the
icon.
Sub-page
object
Sub-page
Go to the sub-page
16
5.2 Communication - Available functions and their configuration
This group includes the objects of the basic door entry system functions.
Object description
Configuration
Camera activation
Camera
Staircase light switching on
Staircase lights
Conversation with other system
handsets
Intercom
Cyclical activation of the system
cameras
Camera cycling
Connection to a page where the
user can include communication
specific objects
Communication
Opening of a door lock
Open door
Enter the
description
TiPolyxMemoryDisplay
User guide
17
Configuration
Enter the address:
• Camera
• Camera from which cycling should start
• Handset with which to communicate
• Lock to open
Enter the description
18
5.3 Home automation - Available functions and their configuration
This group includes the objects of the home automation functions.
Object description
Configuration
Alarms
Information on the status of the
burglar alarm system
Alarms
Temperature control system man-
agement (up to 99 zones)
Temp. control 99 zones
Temperature control system man-
agement (up to 4 zones)
Temp. control 4 zones
Activation of the scenario saved in a
scenario module
Scenario module
Sound system management
Sound system
Execution of a scenario saved in a
scenario programmer
Start scheduled scen.
Activation of the scenarios saved in
a scenario central unit
Scenario central unit
Multichannel sound system man-
agement
Multichannel sound system
Interruption of a scenario saved in a
scenario programmer
Stop scheduled scen.
Connection to a page where to in-
sert scenario objects
Scenarios
Enter the zone
description
Enter the auxiliary
channel description
Zone
presence
Type of
auxiliary
channel
Auxiliary channel
presence
TiPolyxMemoryDisplay
User guide
19
Sound system
Add amplifier
Add source
Enter the
description
Enter the
amplifier
address
Enter the source address
Enter the source
description
20
Enter the address of
the module or the
scenario central unit
Enter the CEN
control address
Enter the description
Enter the description
Scenario no.
Scenario no.
Scenarios
Scheduled scenarios
/