DFI CP330-NRM User manual

CP330-NRM

System Board

User’s Manual

A12760221

Copyright

This publication contains information that is protected by copyright. No part of it

may be reproduced in any form or by any means or used to make any transfor-

mation/adaptation without the prior written permission from the copyright hold-

ers.

This publication is provided for informational purposes only. The manufacturer

makes no representations or warranties with respect to the contents or use

of this manual and specifically disclaims any express or implied warranties of

merchantability or fitness for any particular purpose. The user will assume the

entire risk of the use or the results of the use of this document. Further, the

manufacturer reserves the right to revise this publication and make changes to

its contents at any time, without obligation to notify any person or entity of such

revisions or changes.

Trademarks

Product names or trademarks appearing in this manual are for identification pur-

pose only and are the properties of the respective owners.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment

is operated in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorientorrelocatethereceivingantenna.

• Increasetheseparationbetweentheequipmentandthereceiver.

• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhich

the receiver is connected.

• ConsultthedealeroranexperiencedradioTVtechnicianforhelp.

Notice:

1. The changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission

limits.

1

4

Introduction

Table of Contents

Copyright ........................................................................................... 2

Trademarks ........................................................................................ 2

FCC and DOC Statement on Class B .............................................. 3

About this Manual ............................................................................. 7

Warranty .......................................................................................... 7

Static Electricity Precautions ............................................................. 8

Safety Measures ................................................................................. 8

About the Package ............................................................................ 9

Before Using the System Board ........................................................ 9

Chapter 1 - Introduction ................................................................ 10

Specifications ................................................................................ 10

Features ...................................................................................... 12

Chapter 2 - Hardware Installation .................................................. 16

System Board Layout .................................................................... 16

System Memory ........................................................................... 17

Installing the DIM Module ......................................................... 18

CPU ............................................................................................ 20

Installing the CPU .................................................................... 20

Installing the Fan and Heat Sink ................................................ 22

Jumper Settings ............................................................................. 24

Clear CMOS Data ..................................................................... 24

PS/2 Power Select .................................................................... 25

USB Power Select ..................................................................... 26

Panel Power Select ................................................................... 27

COM 3 RS232/RS422/RS485 Select ............................................ 28

COM 2 RS232/Power Select ....................................................... 29

Power-on Select ....................................................................... 30

CompactFlash Card Setting ....................................................... 31

Rear Panel I/O Ports ..................................................................... 32

PS/2 Mouse and PS/2 Keyboard Ports ......................................... 33

COM (Serial) Ports ................................................................... 34

VGAPort ................................................................................. 36

DVI-IPort ............................................................................... 37

RJ45 LAN Port ......................................................................... 38

1

5

Introduction

USB Ports................................................................................ 39

Audio ..................................................................................... 41

I/O Connectors ............................................................................ 43

CD-in Internal Audio Connector ................................................. 43

S/PDIF Connector ..................................................................... 44

LVDS LCD Panel and LCD/Inverter Power Connector ..................... 45

Digital I/O Connector ................................................................ 47

SATA (Serial ATA) Connectors .................................................... 48

IDE Connector ......................................................................... 49

FDD Connector ........................................................................ 51

Cooling Fan Connectors ............................................................. 52

Chassis Instrusion Connector .................................................... 53

Power Connector ...................................................................... 54

Standby Power LED .................................................................. 55

Front Panel Connectors ............................................................. 56

Expansion Slots ....................................................................... 57

Battery ................................................................................... 58

CompactFlash Socket ................................................................ 59

Chapter 3 - BIOS Setup .................................................................. 60

Overview .................................................................................... 60

Default Configuration .................................................................. 60

Entering the BIOS Setup Utility .................................................... 60

Legends ...................................................................................... 61

Main ........................................................................................... 62

Advanced ..............................................................................................................63

Chipset .................................................................................................................. 80

Boot .......................................................................................................................86

Security .................................................................................................................87

Save & Exit ........................................................................................................... 88

Updating the BIOS ........................................................................ 89

Chapter 4 - Supported Software ................................................... 90

Drivers, Utilities and Software Applications.................................................90

Microsoft .NET Framework 3.5 ................................................... 91

Microfoft DirectX 9.0C ............................................................... 93

Intel Chipset Software Installation Utility .................................... 94

Intel Graphics Drivers ............................................................... 96

Intel Management Engine Drivers .............................................. 98

Intel Rapid Storage Drivers ..................................................... 100

Audio Drivers ......................................................................... 102

Intel LAN Drivers ................................................................... 103

Realtek LAN Drivers ............................................................... 105

F6 Floppy .............................................................................. 106

MyGuard Hardware Monitor ..................................................... 107

DFI Utility ............................................................................. 109

Intel Turbo Boost Monitor ........................................................ 112

Adobe Acrobat Reader 9.3 ....................................................... 114

1

6

Introduction

Chapter 5 - RAID ........................................................................ 116

RAID Levels .......................................................................................................116

Settings ................................................................................................................117

Chapter 6 - Intel AMT Settings ................................................... 121

Overview ............................................................................................................121

Enable Intel® AMT in the AMI BIOS ...........................................................122

Enable Intel® AMT in the Intel® Management Engine BIOS

Extension (MEBX) Screen ..............................................................................

125

Appendix A - Watchdog Sample Code ......................................... 156

Appendix B - System Error Message ............................................ 157

Appendix C - Troubleshooting ...................................................... 159

1

7

Introduction

About this Manual

An electronic file of this manual is included in the CD. To view the user’s manual

in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board

Utility CD) will appear. Click “User’s Manual” on the main menu.

Warranty

1. Warranty does not cover damages or failures that arised from misuse of the

product, inability to use the product, unauthorized replacement or alteration

of components and product specifications.

2. The warranty is void if the product has been subjected to physical abuse,

improper installation, modification, accidents or unauthorized repair of the

product.

3. Unless otherwise instructed in this user’s manual, the user may not, under

any circumstances, attempt to perform service, adjustments or repairs on the

product, whether in or out of warranty. It must be returned to the purchase

point, factory or authorized service agency for all such work.

4. We will not be liable for any indirect, special, incidental or consequencial

damages to the product that has been modified or altered.

1

8

Introduction

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board, components

or devices even before installing them in your system unit. Static electrical dis-

charge can damage computer components without causing any signs of physical

damage. You must take extra care in handling them to ensure against electro-

static build-up.

1. To prevent electrostatic build-up, leave the system board in its anti-static bag

until you are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of the compo-

nents, contacts or connections.

5. Avoid touching the pins or contacts on all modules and connectors. Hold

modules or connectors by their ends.

Important:

Electrostatic discharge (ESD) can damage your processor, disk drive and

other components. Perform the upgrade instruction procedures described

at an ESD workstation only. If such a station is not available, you can

provide some ESD protection by wearing an antistatic wrist strap and

attaching it to a metal part of the system chassis. If a wrist strap is

unavailable, establish and maintain contact with the system chassis

throughout any procedures requiring ESD protection.

Safety Measures

To avoid damage to the system:

• UsethecorrectACinputvoltagerange.

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis cover for instal-

lation or servicing. After installation or servicing, cover the system chassis

before plugging the power cord.

Battery:

• Dangerofexplosionifbatteryincorrectlyreplaced.

• Replace only with the same or equivalent type recommend by the manufac-

turer.

• Disposeofusedbatteriesaccordingtolocalordinance.

1

9

Introduction

About the Package

The system board package contains the following items. If any of these items are

missing or damaged, please contact your dealer or sales representative for as-

sistance.

 One system board

 One IDE cable

 Two USB cables

 Two Serial ATA data cables

 Two Serial ATA power cables

 One bracket mounted with a COM port

 One I/O shield

 One CD

 One QR (Quick Reference)

The system board and accessories in the package may not come similar to the

information listed above. This may differ in accordance to the sales region or

models in which it was sold. For more information about the standard package in

your region, please contact your dealer or sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will need at least the

following internal components.

• ACPU

• Memorymodule

• Storagedevicessuchasharddiskdrive,CD-ROM,etc.

You will also need external system peripherals you intend to use which will nor-

mally include at least a keyboard, a mouse and a video display monitor.

1

10

Introduction

Processor

Chipset

System Memory

Expansion Slots

Graphics

Audio

LAN

Serial ATA

IDE

AMT

Chapter 1 - Introduction

•SocketGrPGA988Afor:

- Intel

®

Core

TM

i7-620M (SV)

- Intel

®

Core

TM

i5-520M (SV)

- Intel

®

Celeron

®

P4500 (SV)

•SupportsIMVP6.5upto35WCPU

•Intel

®

QM57PCH(PlatformControllerHub)

•Two204-pinSODIMMsockets

•SupportsDDR3800/1066MHz(PC3-6400/PC3-8500)

•Supportsdualchannelmemoryinterface

•Supportsupto8GBsystemmemory

•DRAMdevicetechnologies:1Gb and 2Gb DDR3 DRAMtech-

nologies are suported for x8 and x16 devices, unbuffered,

non-ECC

•1PCIExpressx16slot

•1PCIExpressx4slot

•2PCIslots

•1CompactFlashsocket

•Intel

®

HD Graphics

•Displayports:DVI-I(CH7318),LVDSandVGA

•LVDS:SingleChannel-18/24-bit;DualChannel-36/48-bit

•Intel

®

ClearVideotechnology

•Intel

®

DynamicVideoMemoryTechnology(Intel

®

DVMT)

•Intel

®

Smart2DDisplayTechnology(Intel

®

S2DDT)

•RealtekALC2622-channelHighDefinitionAudio

•HighperformanceDACswith100dBSNR

•ADCswith90dBSNR

•Two stereo DACs support 24-bit PCM format for stereo au-

dioplayback

•Three stereo ADCs support 20-bit PCM format for multiple

inputstreaming

•S/PDIFaudiointerface

•Intel82577LMwithiAMT6.0GigabitEthernetPhy

•RealtekRTL8111CPCIExpressGigabitEthernetcontroller

•Integrated10/100/1000transceiver

•FullycompliantwithIEEE802.3,IEEE802.3u,IEEE802.3ab

•Supportswiremanagement

•6SerialATAportscompliantwithSATA1.0aspecification

•SATAspeedupto3Gb/s(SATA2.0)

•Integrated Advanced Host Controller Interface (AHCI) control-

ler

•SupportsRAID0/1/5/10

•JMicronJMB368PCIExpresstoPATAhostcontroller

•DMAmode:UltraATAupto100MB/s

•PIOmode:upto16MB/s

•SupportsiAMT6.0

•Out-of-bandsystemaccess

•Remotetroubleshootingandrecovery

Specifications

1

11

Introduction

TPM (optional)

RearPanelI/O

Ports

I/OConnector

BIOS

Energy Efficient

Design

Damage F r e e

Intelligence

Temperature

Humidity

PCB

•Hardware-basedagentpresencechecking

•Proactivealerting

•Remotehardwareandsoftwareassettracking

•ProvidesaTrustedPCforsecuretransactions

•Providessoftwarelicenseprotection,enforcementandpass-

 wordprotection

•1mini-DIN-6PS/2mouseport

•1mini-DIN-6PS/2keyboardport

•2DB-9RS232serialports

-Pins1and9ofCOM2functionsasRS232signalorpower

(selectableviajumper)

•1DB-15VGAport

•1DVI-Iport(DVI-Dsignalonly)

•2RJ45LANports

•4USB2.0/1.1ports

•Mic-in,line-inandlineoutjacks

•4connectorsfor8externalUSB2.0/1.1ports

•2connectorsfor2externalserialports

-COM3supportsRS232/422/485

•1LVDSLCDpanelconnector

•1LCD/inverterpowerconnector

•18-bitDigitalI/Oconnector

•1frontaudioconnectorforline-outandmic-injacks

•1CD-inconnector

•1S/PDIFconnector

•6SerialATAconnectors

•134-pinFDDconnector

•140-pinIDEconnector

•124-pinATXpowerconnector

•1frontpanelconnectorand3fanconnectors

•AMIBIOS

•64MbitSPIBIOS

•ACPIv2.0specification

•SystemPowerManagement

•Wake-On-Eventsinclude:

 - Wake-On-PS/2KB/Mouse

- Wake-On-USBKB/Mouse

 - Wake-On-LAN

- Wake-On-Ring

 - RTCtimertopower-onthesystem

•CPUstoppedclockcontrol

•ACpowerfailurerecovery

•MonitorsCPU/systemtemperatureandoverheatalarm

•Monitors Vcore/12V/1.5V/1.05V/5V/3VSB voltages and fail-

ure alarm

•MonitorsCPU/chassis/2ndfanspeedandfailurealarm

•Readback capabilitythatdisplays temperature,voltage and

fanspeed

•Watchdogtimerfunction

•0

o

C to 60

o

C

•10%to90%

•MicroATXformfactor

•244mm(9.6”)x224mm(8.82”)

1

12

Introduction

Features

Watchdog Timer

The Watchdog Timer function allows your application to regularly “clear” the sys-

tem at the set time interval. If the system hangs or fails to function, it will reset

at the set time interval so that your system will continue to operate.

DDR3

DDR3 delivers increased system bandwidth and improved performance. It offers

peak data transfer rate of up to 21 Gb/s bandwidth. The advantages of DDR3

are its higher bandwidth and its increase in performance at a lower power than

DDR2.

Graphics

The integrated Intel Gen5.75 graphics engine delivers an excellent blend of

graphics performance and features to meet business needs. With support for In-

tel Clear Video technology, Intel DVMT and Intel S2DDT, Intel Gen5.75 provides

excellent video and 3D graphics with outstanding graphics responsiveness. These

enhancements deliver the performance and compatibility needed for today’s and

tomorrow’s business applications.

DVI

DVI (Digital Visual Interface) is a form of video interface technology made to

maximize the quality of flat panel LCD monitors and modern video graphics

cards. Data is transmitted using the TMDS (Transition Minimized Differential Sig-

naling) protocol, providing a digital signal from the PC’s graphics subsystem to

the display.

LVDS

The Low-Voltage Differential Signaling (LVDS) interface allows the Intel Graphics

Media Adapter to communicate directly to the flat-panel display. The LVDSinter-

face supports pixel color depths of 18 and 24 bits.

PCI Express

PCI Express is a high bandwidth I/O infrastructure that possesses the ability to

scale speeds by forming multiple lanes. The x4 PCI Express lane supports trans-

fer rate of 1 Gigabyte per second. The PCI Express architecture also provides a

high performance graphics infrastructure by enhancing the capability of a x16 PCI

Express lane to provide 4 Gigabytes per second transfer rate.

1

13

Introduction

Intel Active Management Technology (AMT)

Intel Active Management Technology (Intel

®

AMT) allows remote access and man-

agement of networked systems even while PCs are powered off, remotely repair

systems after OS failures and has the capability to remotely update all systems

with the latest security software.

S/PDIF

S/PDIF is a standard audio file transfer format that transfers digital audio sig-

nals to a device without having to be converted first to an analog format. This

prevents the quality of the audio signal from degrading whenever it is converted

to analog. S/PDIF is usually found on digital audio equipment such as a DAT

machine or audio processing device. The S/PDIF connector on the system board

sends surround sound and 3D audio signal outputs to amplifiers and speakers

and to digital recording devices like CD recorders.

Serial ATA

Serial ATA is a storage interface that is compliant with SATA 1.0a specification.

With speed of up to 3Gbps, it improves hard drive performance faster than the

standard parallel ATA whose data transfer rate is 100MB/s. The system board

supports RAID 0, RAID 1, RAID 5 and RAID 10.

Gigabit LAN

The Intel 82577LM Gigabit LAN Phy supports iAMT6.0 while the Realtek RTL8111C

PCI Express Gigabit controller supports up to 1Gbps data transmission.

USB

The system board supports USB 2.0 and USB 1.1 ports. USB 1.1 supports 12Mb/

second bandwidth while USB 2.0 supports 480Mb/second bandwidth providing a

marked improvement in device transfer speeds between your computer and a

wide range of simultaneously accessible external Plug and Play peripherals.

CompactFlash

The system board is equipped with the CompactFlash

TM

socket for inserting a

CompactFlash

TM

card. CompactFlash

TM

card is a small removable mass storage

device designed with flash technology - a non-volatile storage solution that does

not require a battery to retain data indefinitely. The CompactFlash

TM

technology

is widely used in products such as portable and desktop computers, digital cam-

eras, handheld data collection scanners, PDAs, Pocket PCs, handy terminals and

personal communicators.

1

14

Introduction

Wake-On-Ring

This feature allows the system that is in the Suspend mode or Soft Power Off

mode to wake-up/power-on to respond to calls coming from an external modem

or respond to calls from a modem PCI card that uses the PCI PME (Power Man-

agement Event) signal to remotely wake up the PC.

Important:

The 5V_standby power source of your power supply must support

≥720mA.

Wake-On-LAN

This feature allows the network to remotely wake up a Soft Power Down (Soft-

Off) PC. It is supported via the onboard LAN port or via a PCI LAN card that uses

the PCI PME (Power Management Event) signal. However, if your system is in the

Suspend mode, you can power-on the system only through an IRQ or DMA inter-

rupt.

Important:

The 5V_standby power source of your power supply must support

≥720mA.

Wake-On-PS/2

This function allows you to use the PS/2 keyboard or PS/2 mouse to power-on

the system.

Important:

The 5V_standby power source of your power supply must support

≥720mA.

Wake-On-USB

This function allows you to use a USB keyboard or USB mouse to wake up a sys-

tem from the S3 (STR - Suspend To RAM) state.

Important:

If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB

ports, the 5V_standby power source of your power supply must support

≥1.5A. For 3 or more USB ports, the 5V_standby power source of your

powersupplymustsupport≥2A.

RTC Timer

The RTC installed on the system board allows your system to automatically pow-

er-on on the set date and time.

1

15

Introduction

ACPI STR

The system board is designed to meet the ACPI (Advanced Configuration and

Power Interface) specification. ACPI has energy saving features that enables PCs

to implement Power Management and Plug-and-Play with operating systems that

support OS Direct Power Management. ACPI when enabled in the Power Manage-

ment Setup will allow you to use the Suspend to RAM function.

With the Suspend to RAM function enabled, you can power-off the system at

once by pressing the power button or selecting “Standby” when you shut down

Windows

®

without having to go through the sometimes tiresome process of

closing files, applications and operating system. This is because the system is

capable of storing all programs and data files during the entire operating session

into RAM (Random Access Memory) when it powers-off. The operating session will

resume exactly where you left off the next time you power-on the system.

Important:

The 5V_standby power source of your power supply must support

≥720mA.

Power Failure Recovery

When power returns after an AC power failure, you may choose to either power-

on the system manually or let the system power-on automatically.

16

2

Hardware Installation

System Board Layout

Chapter 2 - Hardware Installation

LAN1(Intel)

USB 1

USB 0

Mic-in

VGA

DVI -I

SPI Flash

BIOS

PCI 1

DVI-I port

(DVI-D signal only)

LAN2(Realtek)

USB 9

USB 8

Line-in

Line-out

Chrontel

CH7318C

2

9

10

COM 2

COM 1

COM 4

1

COM 3

1

2

19

1

PCI 2

Battery

1

Front

panel

2

11

1

AT X power

1

System fan

1

11

SATA 0

1

SATA 1

1

SATA 2

1

Front

audio

1

S/PDIF

1

CD-in

1

PS/2 Mouse

PS/2 KB

2

9

1

2

9

PS/2 power

select (JP2)

COM3 RS232/422/485

select ()JP4

2

56

13

12

24

1

Power-on

select ()JP7

COM2 RS232/Power

select (JP3)

1

2

5

6

So c ket G

rP G A 988A

CPU fan

USB 0-1, 8-9

power select (JP5)

1

2

5

6

LCD/Inverter

power

Panel power

select ()JP15

LVDS LCD

panel

12

39

40

DDR3_2 SODIMM

DDR3_1 SODIMM

Intel

QM57

CF card setting

(JP10)

CompactFlash

12

3940

SATA 3

SATA 4

SATA 5

Chassis

intrusion

1

PCI Express x16

PCI Express x4

1

DIO

1

2

33

34

USB 10-11

USB 2-3

USB 6-7

USB 4-5

USB 2-3, 10-11

power select (JP6)

USB 4-7 power

select (JP8)

11

Clear CMOS

(JP9)

2nd fan

IDE

FDD

Fintek

F71879

Standby

Power LED

17

2

Hardware Installation

Important:

When the Standby Power LED lit red, it indicates that there is power on

the system board. Power-off the PC then unplug the power cord prior to

installing any devices. Failure to do so will cause severe damage to the

motherboard and components.

System Memory

Important:

Electrostatic discharge (ESD) can damage your system board, processor,

disk drives, add-in boards, and other components. Perform the upgrade

instruction procedures described at an ESD workstation only. If such a

station is not available, you can provide some ESD protection by wearing

an antistatic wrist strap and attaching it to a metal part of the system

chassis. If a wrist strap is unavailable, establish and maintain contact

with the system chassis throughout any procedures requiring ESD pro-

tection.

DDR3-1

Standby

Power LED

The system board is equipped with two 204-pin SODIMM sockets that support

DDR3 memory modules.

DDR3-2

18

2

Hardware Installation

Installing the DIM Module

Note:

The system board used in the following illustrations may not resemble

the actual one. These illustrations are for reference only.

1. Make sure the PC and all other peripheral devices connected to it has been

powered down.

2. Disconnect all power cords and cables.

3. Locate the SODIMM socket on the system board.

4. Note the key on the socket. The key ensures the module can be plugged into

the socket in only one direction.

19

2

Hardware Installation

6. Push down the module until the clips at each end of the socket lock into

position. You will hear a distinctive “click”, indicating the module is correctly

locked into position.

Clip

5. Grasping the module by its edges, align the module into the socket at an ap-

proximately 30 degrees angle. Apply rm even pressure to each end of the

module until it slips down into the socket. The contact ngers on the edge of

the module will almost completely disappear inside the socket.

20

2

Hardware Installation

CPU

Overview

The system board is equipped with a surface mount rPGA 988A CPU socket.

Note:

The system board used in the following illustrations may not resemble

the actual one. These illustrations are for reference only.

Installing the CPU

1. Make sure the PC and all other peripheral devices connected to it has been

powered down.

2. Disconnect all power cords and cables.

3. Lo cat e the rP G A 988 A

socke t on t h e sy s t e m

board.

4. Make sure the screw is in

its unlock position. If it’s

not, use a screwdriver to

turn the screw to its unlock

position.

Screw in unlocked

position

Page is loading ...

DFI CP330-NRM User manual

DFI CP330-NRM User manual

Related papers

Other documents