DFI HR100-CRM User manual

Category
Motherboards
Type
User manual
HR100-CRM
System Board
User’s Manual
A15380443
Copyright
This publication contains information that is protected by copyright. No part of it
may be reproduced in any form or by any means or used to make any transfor-
mation/adaptation without the prior written permission from the copyright hold-
ers.
This publication is provided for informational purposes only. The manufacturer
makes no representations or warranties with respect to the contents or use
of this manual and specifically disclaims any express or implied warranties of
merchantability or fitness for any particular purpose. The user will assume the
entire risk of the use or the results of the use of this document. Further, the
manufacturer reserves the right to revise this publication and make changes to
its contents at any time, without obligation to notify any person or entity of such
revisions or changes.
Changes after the publication’s first release will be based on the product’s revi-
sion. The website will always provide the most updated information.
© 2014. All Rights Reserved.
Trademarks
All trademarks and registered trademarks of products appearing in this manual
are the properties of their respective holders.
FCC and DOC Statement on Class B
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio TV technician for help.
Notice:
1. The changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission
limits.
1
4
Introduction
Table of Contents
Copyright ........................................................................................... 2
Trademarks ........................................................................................ 2
FCC and DOC Statement on Class B .............................................. 3
About this Manual ............................................................................. 6
Warranty .......................................................................................... 6
Static Electricity Precautions ............................................................. 7
Safety Measures ................................................................................. 7
About the Package ............................................................................ 8
Before Using the System Board ........................................................ 8
Chapter 1 - Introduction .................................................................. 9
Specifications .................................................................................. 9
Features ...................................................................................... 12
Chapter 2 - Hardware Installation .................................................. 15
System Board Layout .................................................................... 15
System Memory ........................................................................... 16
Installing the DIM Module ......................................................... 17
CPU ............................................................................................ 19
Installing the CPU .................................................................... 19
Installing the Fan and Heat Sink ................................................ 21
Jumper Settings ............................................................................. 23
Clear CMOS Data ..................................................................... 23
PS/2 Power Select .................................................................... 24
USB Power Select ..................................................................... 25
Panel Power Select ................................................................... 26
COM1/COM2 RS232/RS422/RS485 Select.................................... 27
COM1/COM2 RS232/Power Select............................................... 28
Power-on Select ....................................................................... 29
Rear Panel I/O Ports ..................................................................... 30
PS/2 Mouse and PS/2 Keyboard Ports ......................................... 31
COM (Serial) Ports ................................................................... 32
VGA Port ................................................................................. 33
DVI-I Port ............................................................................... 34
RJ45 LAN Ports ........................................................................ 35
USB Ports................................................................................ 36
Audio ...................................................................................... 38
I/O Connectors ............................................................................ 40
CD-in Internal Audio Connector ................................................. 40
S/PDIF Connector ..................................................................... 41
1
5
Introduction
LVDS LCD Panel Connector ........................................................ 42
LCD/Inverter Power Connector ................................................... 42
Digital I/O Connectors .............................................................. 44
SATA (Serial ATA) Connectors .................................................... 45
Cooling Fan Connectors ............................................................. 46
Chassis Instrusion Connector .................................................... 47
Power Connectors .................................................................... 48
Standby Power LED .................................................................. 50
Front Panel Connectors ............................................................. 51
Expansion Slots ....................................................................... 52
Battery ................................................................................... 55
CompactFlash Socket (optional) ................................................. 56
Chapter 3 - BIOS Setup .................................................................. 57
Overview ..............................................................................................................57
AMI BIOS Setup Utility ................................................................. 59
Main ....................................................................................... 59
Advanced ................................................................................ 60
Chipset ................................................................................... 76
Boot ....................................................................................... 83
Security .................................................................................. 84
Save & Exit ............................................................................. 85
Updating the BIOS ........................................................................ 86
Notice: BIOS SPI ROM .................................................................. 87
Chapter 4 - Supported Software ................................................... 88
Chapter 5 - RAID ........................................................................ 115
RAID Levels .......................................................................................................115
Settings ................................................................................................................116
Chapter 6 - Intel AMT Settings ................................................... 120
Overview ............................................................................................................120
Enable Intel
®
AMT in the AMI BIOS ............................................................121
Enable Intel
®
AMT in the Intel
®
Management Engine BIOS
Extension (MEBX) Screen ..............................................................................
123
Appendix A - NLITE and AHCI Installation Guide ....................... 152
Appendix B - Watchdog Sample Code ......................................... 164
Appendix C - System Error Message ............................................ 165
Appendix D - Troubleshooting ...................................................... 167
1
6
Introduction
About this Manual
An electronic file of this manual is included in the CD. To view the user’s manual
in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board
Utility CD) will appear. Click “User’s Manual” on the main menu.
Warranty
1. Warranty does not cover damages or failures that arised from misuse of the
product, inability to use the product, unauthorized replacement or alteration
of components and product specifications.
2. The warranty is void if the product has been subjected to physical abuse,
improper installation, modification, accidents or unauthorized repair of the
product.
3. Unless otherwise instructed in this user’s manual, the user may not, under
any circumstances, attempt to perform service, adjustments or repairs on the
product, whether in or out of warranty. It must be returned to the purchase
point, factory or authorized service agency for all such work.
4. We will not be liable for any indirect, special, incidental or consequencial
damages to the product that has been modified or altered.
1
7
Introduction
Static Electricity Precautions
It is quite easy to inadvertently damage your PC, system board, components
or devices even before installing them in your system unit. Static electrical dis-
charge can damage computer components without causing any signs of physical
damage. You must take extra care in handling them to ensure against electro-
static build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag
until you are ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the compo-
nents, contacts or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold
modules or connectors by their ends.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and
other components. Perform the upgrade instruction procedures described
at an ESD workstation only. If such a station is not available, you can
provide some ESD protection by wearing an antistatic wrist strap and
attaching it to a metal part of the system chassis. If a wrist strap is
unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
Safety Measures
To avoid damage to the system:
Use the correct AC input voltage range.
To reduce the risk of electric shock:
Unplug the power cord before removing the system chassis cover for instal-
lation or servicing. After installation or servicing, cover the system chassis
before plugging the power cord.
Battery:
Danger of explosion if battery incorrectly replaced.
Replace only with the same or equivalent type recommend by the manufac-
turer.
Dispose of used batteries according to local ordinance.
1
8
Introduction
About the Package
The system board package contains the following items. If any of these items are
missing or damaged, please contact your dealer or sales representative for as-
sistance.
One HR100-CRM motherboard
Two Serial ATA data cables
Two Serial ATA power cables
Two USB cables
One bracket mounted with a COM port cable
One I/O shield
One DVD
One QR (Quick Reference)
Optional Items
USB port cable
COM port cable
Serial ATA data cable
Serial ATA power cable
I/O shield
The system board and accessories in the package may not come similar to the
information listed above. This may differ in accordance to the sales region or
models in which it was sold. For more information about the standard package in
your region, please contact your dealer or sales representative.
Before Using the System Board
Before using the system board, prepare basic system components.
If you are installing the system board in a new system, you will need at least the
following internal components.
• A CPU
• Memory module
Storage devices such as hard disk drive, CD-ROM, etc.
You will also need external system peripherals you intend to use which will nor-
mally include at least a keyboard, a mouse and a video display monitor.
1
9
Introduction
Processor
Chipset
System Memory
Expansion Slots
Graphics
Chapter 1 - Introduction
Socket G2 988B for:
- 3rd Generation Intel
®
Core™ processors
(22nm process technology) (Rev. AG0 or later)
: Intel
®
Core™ i7-3610QE (6M Cache, up to 3.3 GHz); 45W
: Intel
®
Core™ i5-3610ME (3M Cache, up to 3.3 GHz); 35W
: Intel
®
Core
TM
i3-3120ME (3M Cache, 2.4GHz); 35W
- 2nd Generation Intel
®
Core™ processors
(32nm process technology)
: Intel
®
Core™ i7-2710QE (6M Cache, up to 3.0 GHz); 45W
: Intel
®
Core™ i5-2510E (3M Cache, up to 3.1 GHz); 35W
: Intel
®
Core
TM
i3-2330E (3M Cache, 2.2 GHz); 35W
: Intel
®
Celeron
®
B810 (2M Cache, 1.6 GHz); 35W
• Intel
®
Advanced Vector Extensions (Intel
®
AVX) Instructions
• Intel
®
Turbo Boost Technology
• Intel
®
QM67 Express Chipset
Two 204-pin DDR3 SODIMM sockets
Supports DDR3 1333/1600MHz (3rd generation processors)
Supports DDR3 1066/1333MHz (2nd generation processors)
Supports dual channel memory interface
Supports up to 16GB system memory
DRAM device technologies: 1Gb, 2Gb and 4Gb DDR3 DRAM
technologies are supported for x8 and x16 devices, unbuf-
fered, non-ECC
1 PCIe x16 slot
- Supports Gen 3.0 (3rd generation processors)
- Supports Gen 2.0 (2nd generation processors)
- Switchable with SDVO/HDMI/DP
- Configurations (supported only via a riser card):
: One x8 (GFX) and two x4 (I/O)
: Two x8 (GFX, I/O)
: One x16 (GFX, I/O)
2 DFI Proprietary Extension bus for
PCIe/PCI expansion
1 CompactFlash socket (optional)
• Intel
®
HD Graphics
Display ports: DVI-D (ASMedia 1442), LVDS and VGA
DVI: resolution up to 1920x1200 @60Hz
LVDS: Single Channel - 18/24-bit; Dual Channel: 36/48-bit
,
resolution up to 1920x1200 @60Hz
VGA: resolution up 2048x1536 @75Hz
Supports 6 Graphics Execution Units (EUs)
• Intel
®
Clear Video Technology
DirectX Video Acceleration (DXVA) support for accelerating
video processing
Specifications
1
10
Introduction
Audio
LAN
Serial ATA
CompactFlash
Intel Active
Management
Technology
(AMT)
TPM (optional)
Rear Panel I/O
Ports
Energy Efficient
Design
Realtek ALC262 2-channel High Definition Audio
High performance DACs with 100dB SNR
ADCs with 90dB SNR
Two stereo DACs support 24-bit PCM format for stereo au-
dio playback
Three stereo ADCs support 20-bit PCM format for multiple
input streaming
S/PDIF audio interface
• Intel
®
82579LM with iAMT7.0 Gigabit Ethernet Phy
Realtek RTL8111DL PCI Express Gigabit Ethernet controller
Integrated 10/100/1000 transceiver
Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
4 Serial ATA ports
- 2 SATA 2.0 ports with data transfer rate up to 3Gb/s
- 2 SATA 3.0 ports with data transfer rate up to 6Gb/s
Integrated Advanced Host Controller Interface (AHCI) con-
troller
Supports RAID 0/1/5/10
JMicron JMB368 PCI Express to PATA host controller
DMA mode: Ultra ATA up to 100MB/s
PIO mode: up to 16MB/s
• Supports iAMT7.0
Out-of-band system access
Remote troubleshooting and recovery
Hardware-based agent presence checking
• Proactive alerting
Remote hardware and software asset tracking
Provides a Trusted PC for secure transactions
Provides software license protection, enforcement and pass-
word protection
1 mini-DIN-6 PS/2 mouse port
1 mini-DIN-6 PS/2 keyboard port
2 DB-9 serial ports
- Supports RS232/422/485
- Pins 1 and 9 of RS232 functions as RS232 signal or power
(selectable via jumper)
1 DB-15 VGA port
1 DVI-I port (DVI-D signal)
2 RJ45 LAN ports
4 USB 2.0/1.1 ports
Mic-in, Line-in and Line-out jacks
Supports ErP Lot6 power saving (optional)
Supports ACPI
• System Power Management
• Wake-On-Events include:
- Wake-On-PS/2 KB/Mouse
- Wake-On-USB KB/Mouse
- Wake-On-LAN
- RTC timer to power-on the system
• CPU stopped clock control
• AC power failure recovery
1
11
Introduction
I/O Connectors
Damage Free
Intelligence
BIOS
Power
Consumption
OS Support
Temperature
Humidity
Dimensions
Certification
• 2 connectors for 4 external USB 2.0/1.1 ports
• 4 connectors for 4 external RS232 serial ports
• 1 LVDS LCD panel connector
• 1 LCD/inverter power connector
• 1 8-bit Digital I/O connector
• 1 front audio connector for line-out and mic-in jacks
• 1 S/PDIF connector
• 4 Serial ATA ports
• 1 24-pin ATX power connector
• 1 chassis intrusion connector
• 1 front panel connector
• 2 fan connectors
Monitors CPU/system temperature and overheat alarm
Monitors VCORE/5V/1.05V/1.5V/12V/3.3V/VBAT voltages
and failure alarm
• Monitors CPU/system fan speed and failure alarm
• Read back capability that displays temperature, voltage and
fan speed
• Watchdog timer function
• AMI BIOS
- 64Mbit SPI BIOS
64.68 W with i7-2710QE at 2.1GHz and 2x 4GB DD3 SO-
DIMM
• Windows XP Professional x86 & SP3 (32-bit)
• Windows XP Professional x64 & SP2 (64-bit)
• Windows 7 Ultimate x86 & SP1 (32-bit)
• Windows 7 Ultimate x64 & SP1 (64-bit)
• Windows 8 Enterprise x86 (32-bit)
• Windows 8 Enterprise x64 (64-bit)
• 0
o
C to 60
o
C
10% to 90%
• Mini-ITX form factor
- 170mm (6.7”) x 170mm (6.7”)
• Heat spreader with heat sink and fan
- 62mm x 60mm x 42mm
• CE, FCC Class B, UL, RoHS
1
12
Introduction
Features
Watchdog Timer
The Watchdog Timer function allows your application to regularly “clear” the sys-
tem at the set time interval. If the system hangs or fails to function, it will reset
at the set time interval so that your system will continue to operate.
DDR3
DDR3 delivers increased system bandwidth and improved performance. It offers
peak data transfer rate of up to 16Gb/s bandwidth. The advantages of DDR3
are its higher bandwidth and its increase in performance at a lower power than
DDR2.
Graphics
The integrated Intel HD graphics for graphics intensive applications delivers ex-
ceptional 3D, 2D and video capabilities. It supports VGA, DVI-D and LVDS inter-
faces.
DVI
DVI (Digital Visual Interface) is a form of video interface technology made to
maximize the quality of flat panel LCD monitors and modern video graphics
cards. Data is transmitted using the TMDS (Transition Minimized Differential Sig-
naling) protocol, providing a digital signal from the PC’s graphics subsystem to
the display.
PCI Express
PCI Express is a high bandwidth I/O infrastructure that possesses the ability to
scale speeds by forming multiple lanes. The PCI Express architecture provides a
high performance graphics infrastructure by enhancing the capability of a x16 PCI
Express lane to provide 4 Gigabytes per second transfer rate.
Intel Active Management Technology (AMT)
Intel Active Management Technology (Intel
®
AMT) allows remote access and man-
agement of networked systems even while PCs are powered off, remotely repair
systems after OS failures and has the capability to remotely update all systems
with the latest security software.
Audio
The Realtek ALC262 audio codec provides 2-channel High Definition audio output.
1
13
Introduction
Serial ATA
Serial ATA is a storage interface that is compliant with SATA 1.0a specifica-
tion. SATA 3.0 supports speed up to 6Gb/s while SATA 2.0 supports speed up to
3Gb/s. This improves hard drive performance faster than the standard parallel
ATA whose data transfer rate is 100MB/s. The board supports RAID 0/1/5/10.
Gigabit LAN
The Intel W82579LM PHY and Realtek RTL8111DL PCI Express Gigabit controllers
support up to 1Gbps data transmission.
CompactFlash (optional)
The CompactFlash
TM
socket is used for inserting a CompactFlash
TM
card. Compact-
Flash
TM
card is a small removable mass storage device designed with flash tech-
nology - a non-volatile storage solution that does not require a battery to retain
data indefinitely. The CompactFlash
TM
technology is widely used in products such
as portable and desktop computers, digital cameras, handheld data collection
scanners, PDAs, Pocket PCs, handy terminals and personal communicators.
USB
The system board supports USB 2.0 and USB 1.1 ports. USB 1.1 supports 12Mb/
second bandwidth while USB 2.0 supports 480Mb/second bandwidth providing a
marked improvement in device transfer speeds between your computer and a
wide range of simultaneously accessible external Plug and Play peripherals.
Wake-On-LAN
This feature allows the network to remotely wake up a Soft Power Down (Soft-
Off) PC. It is supported via the onboard LAN port or via a PCI LAN card that uses
the PCI PME (Power Management Event) signal. However, if your system is in the
Suspend mode, you can power-on the system only through an IRQ or DMA inter-
rupt.
Important:
The 5V_standby power source of your power supply must support
720mA.
Wake-On-PS/2
This function allows you to use the PS/2 keyboard or PS/2 mouse to power-on
the system.
Important:
The 5V_standby power source of your power supply must support
720mA.
1
14
Introduction
Wake-On-USB
This function allows you to use a USB keyboard or USB mouse to wake up a sys-
tem from the S3 (STR - Suspend To RAM) state.
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB
ports, the 5V_standby power source of your power supply must support
1.5A. For 3 or more USB ports, the 5V_standby power source of your
power supply must support 2A.
RTC Timer
The RTC installed on the system board allows your system to automatically pow-
er-on on the set date and time.
ACPI STR
The system board is designed to meet the ACPI (Advanced Configuration and
Power Interface) specification. ACPI has energy saving features that enables PCs
to implement Power Management and Plug-and-Play with operating systems that
support OS Direct Power Management. ACPI when enabled in the Power Manage-
ment Setup will allow you to use the Suspend to RAM function.
With the Suspend to RAM function enabled, you can power-off the system at
once by pressing the power button or selecting “Standby” when you shut down
Windows
®
without having to go through the sometimes tiresome process of
closing files, applications and operating system. This is because the system is
capable of storing all programs and data files during the entire operating session
into RAM (Random Access Memory) when it powers-off. The operating session will
resume exactly where you left off the next time you power-on the system.
Important:
The 5V_standby power source of your power supply must support
720mA.
Power Failure Recovery
When power returns after an AC power failure, you may choose to either power-
on the system manually or let the system power-on automatically.
15
2
Hardware Installation
System Board Layout
Chapter 2 - Hardware Installation
PS/2 Mouse
PS/2 KB
COM 2
COM 1
DVI-I port
(DVI-D signal only)
VGA
DVI-I
LAN 1 (Intel)
USB 1
USB 0
LAN 2 (Realtek)
USB 9
USB 8
Mic-in
Line-in
Line-out
1
PS/2 power
select (JP2)
1
5
COM1 RS232/Power
select (JP1)
2
6
JP1
1
5
2
6
JP3
COM2 RS232/Power
select (JP3)
1
2
5
6
JP4
1
2
5
6
JP5
COM1 RS232/422/485
select ( )JP4
COM2 RS232/422/485
select ( )JP5
ASMedia
1442
1
CPU fan
DDR3_1 SODIMM
DDR3_2 SODIMM
COM6
1
2
9
COM5
1
2
9
COM4
1
2
9
COM3
1
2
9
13
12
24
1
ATX Power
Power-on
select ( )JP7
1
1
Chassis
intrusion
DIO
1
2
19
1
11
Front
panel
Standby
Power LED
SPI Flash
BIOS
1
System fan
Battery
USB 0-1, 8-9 power
select (JP6)
1
Realtek
ALC262
Front audio
1
CD-in
S/PDIF
1
1
2
9
10
Intel
QM67
SATA 4
1
SATA 5
1
SATA 0
1
SATA 1
1
9
10
USB 2-3
9
USB 4-5
Clear CMOS
(JP10)
1
1
Panel power
select ( )JP9
2
5
6
1
LCD/Inverter
power
LVDS LCD
panel
40 39
21
PCIE x16
PCIE x1 PCIE x1
1
2
1
2
SATA 3.0
SATA 2.0
Socket G2
rPGA 988B
1
CF Card Setting
(JP8)
16
2
Hardware Installation
System Memory
Important:
Electrostatic discharge (ESD) can damage your system board, processor,
disk drives, add-in boards, and other components. Perform the upgrade
instruction procedures described at an ESD workstation only. If such a
station is not available, you can provide some ESD protection by wearing
an antistatic wrist strap and attaching it to a metal part of the system
chassis. If a wrist strap is unavailable, establish and maintain contact
with the system chassis throughout any procedures requiring ESD pro-
tection.
DDR3-2
DDR3-1
Standby
Power LED
Important:
When the Standby Power LED lit red, it indicates that there is power on
the system board. Power-off the PC then unplug the power cord prior to
installing any devices. Failure to do so will cause severe damage to the
motherboard and components.
Features
Two 204-pin DDR3 SODIMM sockets
Supports 1066/1333MHz DDR3 SDRAM
Dual channel memory interface
Supports maximum of 16GB system memory
17
2
Hardware Installation
Note:
The system board used in the following illustrations may not resemble
the actual board. These illustrations are for reference only.
Installing the DIM Module
1. Make sure the PC and all other peripheral devices connected to it has been
powered down.
2. Disconnect all power cords and cables.
3. Locate the DIMM socket on the system board.
4. Push the “ejector tabs” which are at the ends of the socket to the side.
Ejector tab
Ejector tab
5. Note how the module is keyed to the socket.
Key
Notch
18
2
Hardware Installation
7. Seat the module vertically, pressing it down rmly until it is completely seat-
ed in the socket. The ejector tabs at the ends of the socket will automatically
snap into the locked position to hold the module in place.
6. Grasping the module by its edges, position the module above the socket with
the “notch” in the module aligned with the “key” on the socket. The keying
mechanism ensures the module can be plugged into the socket in only one
way.
19
2
Hardware Installation
CPU
Overview
The system board is equipped with a surface mount PGA 988B CPU socket.
Note:
The system board used in the following illustrations may not resemble
the actual one. These illustrations are for reference only.
Installing the CPU
1. Make sure the PC and all other peripheral devices connected to it has been
powered down.
2. Disconnect all power cords and cables.
3. Locate the PGA 988B sock-
et on the system board.
4. Make sure the screw is in
its unlock position. If it’s
not, use a screwdriver to
turn the screw to its un-
lock position.
Lock
Unlock
20
2
Hardware Installation
5. Position the CPU above the
socket. The gold triangular
mark on the CPU must
align with pin 1 of the CPU
socket.
Important:
Handle the CPU by its edg-
es and avoid touching the
pins.
Pin 1
Gold triangular mark
6. Insert the CPU into the
socket until it is seated
in place. The CPU will t
in only one orientation
and can easily be inserted
without exerting any force.
Use a screwdriver to turn
the screw to its lock posi-
tion.
Important:
Do not force the CPU into
the socket. Forcing the
CPU into the socket may
bend the pins and damage
the CPU.
Screw in locked
position
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170

DFI HR100-CRM User manual

Category
Motherboards
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI