INSTALLATION INSTRUCTIONS
Item#2663-723 2663-717 (New. 12/30/2022)
READ AND SAVE THESE INSTRUCTIONS
WA R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig. 3
Fig. 2
ASSEMBLING THE FIXTURE (Fig. 1)
1.
Shut off the power at the fuse box or circuit breaker. If
necessary, remove old fixture, including mounting hardware.
2.
Carefully remove fixture from carton and check that all parts are
included as shown in the illustration.
3. Adjust the arms (I) to proper position. Refer to illustration (L).
4. Screw fixture loop (A) to coupling (B).
MOUNTING THE FIXTURE (Fig. 2)
5. Thread all thread into ceiling loop until snug.
6.
Thread the other end of the all thread into crossbar. Note: The
length of the all thread into crossbar may be adjusted if
necessary.
7. Secure all thread to crossbar with hex nut.
8. Take crossbar assembly and mount it to outlet box (not
included) using the mounting screws (Size: #8-
32N*L1”). The
side of crossbar marked “GND” must face out.
9.
By measuring, determine the correct number of links needed for
desired hanging height. Using chain pliers, disconnect
and
discard excess chain.
10. Open one end of chain
and connect to fixture loop, then close
the chain.
11. Carefully lace fixture wires through chain.
12. Slip lock collar and
canopy over chain and allow them to rest on
fixture body.
13. Open another end of chain and attach it to the ceiling loop
, then
close the chain.
14.
Carefully feed fixture wires through ceiling loop and all thread
and pull until tight.
CONNECTING THE WIRES (Fig. 3)
15.
Connect the electrical wires as shown in Fig. 3 making sure that
all wire connecto
rs are secured. If your outlet box has a ground
wire (green or bare copper), connect the fixture’s ground wire to
it. Otherwise, connect the fixture’s ground wire directly to the
crossbar using the green screw provided.
16. Tuck wire connections neatly into outlet box. R
aise canopy to
ceiling and secure with lock collar.
FINISHING THE INSTALLATION (Fig.1)
17. Place bobeches (K) over candle covers (J).
18. Hang wooden drops (D,M,N,O)
onto fixture body in proper
position.
19. Thread finial (H) to fixture body and attach wooden drops (O).
20. Install (3) three
candelabra base bulbs up to 60 watts each or
CFL or LED equivalent (not included) in accordance with the
fixture specification—
DO NOT EXCEED THE MAXIMUM
WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE
NOMINALE MAXIMALE!).
Your installation is now complete. Return power to the
outlet
box and test the fixture.
Note: Illustration (Fig. 1
) on this manual is for installation
purposes only. It may or may not be identical to the
fixture purchased.
LA-3499E
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
Notice: It is important to use proper chain pliers (not included)
To OPEN and CLOSE the chain included with this fixture. Do
not open them with other tools that may twist or stress
the
chain links. It is important to use
proper chain pliers like the
ones shown in the diagram.
Set# A-010
-Crossbar
-Ground screw
-Mounting Screw *2
Candle Cover (2663-723)# CCV21080P-737
Candle Cover (2663-717)# CCV21080P-778
Chain (2663-723)# HCH1072-737
Chain (2663-717)# HCH1072-778
Code Wooden Drop
For 2663-723
Wooden Drop
For 2663-717
QTY/Item
D WD2669-P1 WD2669-W1 3
M WD2663-P1 WD2663-W1 3
N WD2663-P2 WD2663-W2 6
O WD2663-P3 WD2663-W3 4
/
