INSTALLATION INSTRUCTIONS
Item#1038-677/701 (New. 2022/07/01)
READ AND SAVE THESE INSTRUCTIONS
WA R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig. 3
Fig. 2
Fig. 4
ASSEMBLING THE FIXTURE (Fig. 1
1.
Shut off the power at the fuse box or circuit breaker. If
necessary, remove old fixture, including mounting hardware.
2. Carefully remove the fixture from the cart
parts are included as shown in the illustration.
3. Adjust arms (L) to proper position. (Fig.4)
4. Secure rod (E) onto the all thread (F) on the fixture body.
5. Attach bars (G) to arms (L) and metal plate (D) using screws (H)
and screws (C) as shown in Fig. 1.
6. Place metal cover (B) over all thread on rod (E
fixture loop (A).
HANGING THE FIXTURE (Fig. 2)
7. Thread all thread into ceiling loop until snug.
8.
Thread the other end of all thread into the crossbar. Note: The
length of
all thread into the crossbar may be adjusted if
necessary.
9. Use lock washer and hex nut to secure all thread to crossbar.
10. Take this crossbar assembly and mount it to outlet
included) with mounting screws (Size: #8-
of crossbar marked with “GND” must face out.
11.
Determine the desired hanging height and use a pair of proper
chain pliers to remove and discard the excess chain.
12. Open one end of chain and attach it to fixture loop,
the chain. Slip the lock collar and canopy
allow them to rest on the fixture body. Open the other end of the
chain and attach it to ceiling loop, then close the chain.
13.
Carefully lace fixture’s wires through chain. Feed fixture wires
through ceiling loop and crossbar assembly.
CONNECTING THE WIRE (Fig. 3)
14. C
onnect the electrical wire as shown in figure 3, making sure
that all wire connectors are secured. If your outlet box
ground wire (green or bare copper), connect the fixtures ground
wire to it. Otherwise, connect the fixture
the crossbar using the green screw provided.
15. Tuck wire connections neatly into the outlet box. R
canopy over the ceiling loop and secure with loop collar.
FINISHING THE FIXTURE (Fig.1)
16. Place candle covers (J) over sockets (K).
17. Install (10) ten candelabra base bulbs (I
CFL or LED equivalent (not included) in accordance with the
fixture specification —
DO NOT EXCEED THE MAXIMUM
WATTAGE RATING! (
NE PAS DEPASSER LA PUISSANCE
NOMINALE MAXIMALE!).
Your installation is now complete. Return power to the outlet
and test the fixture.
Note: Illustration (Fig. 1
) on this manual is for installation
purposes only. It may or may not be identical to the
fixture purchased.
LA-3587E
WIRES
Black or
WIRES
Black
(Hot)
WIRES
White or
WIRES
White
(Neutral)
WIRES
Bare
Copper
(Ground)
WIRES
Green
(Ground
)
Notice: It is important to use proper chain pliers (not included)
To OPEN and CLOSE the chain included with this fixture. Do
not open them with other tools that may twist or stress the
chain links. It is important to use proper chain pliers like t
ones shown in the diagram.
-Crossbar
-Ground screw
-Mounting screw*2
CCV21115P-66/701 E
B
C
D
G
H
L
I
J
Chain#HCH2072-66/701
Ceiling Loop
Canopy
Mounting Screw
Crossbar
Hex Nut
Lock Washer
Wire
Chain
Outlet Box
Fixture Loop
1
Minka Lavery 1048-677 User manual
Minka Lavery 1045-677 User manual
Minka Lavery 1047-701 User manual
Minka Lavery 4444-582 User manual
Minka Lavery 4447-582 User manual
Minka Lavery 4445-66A User manual
Minka Lavery 2663-723 User manual
Minka Lavery 3298-613 User manual
Minka Lavery 3297-613 User manual
Minka Lavery 2404-680 User manual
Minka Group 4443-582 User manual
Metropolitan N7764-683 User manual
Minka Group 4449-582 User manual
Minka-Lavery 4087-107 User manual