Aztech VC3000 User manual

VC3000

Aztech Smart Robotic Vacuum Cleaner

USER MANUAL

PLEASE RETAIN THIS USER MANUAL FOR FUTURE USE.

USER MANUAL CONTENTS

SAFETY INSTRUCTIONS 4

PACKAGE CONTENTS 5

APPLIANCE OVERVIEW 5

TOP VIEW 5

BOTTOM VIEW 6

CONTROL PANEL BUTTONS AND DISPLAY 6

REMOTE CONTROL BUTTONS 8

VIRTUAL WALL 9

DOCKING STATION 10

USING THE AZTECH VC3000 10

SETTING THE TIME 12

SETTING THE CURRENT DAY 12

SETTING THE CURRENT TIME 12

SETTING THE CLEANING SCHEDULE 13

SETTING THE DAY SCHEDULE 13

SETTING THE TIME SCHEDULE 13

CARE AND MAINTENANCE 14

REPLACING / INSTALLING THE VC3000’S BATTERY 14

CLEANING THE DUSTBIN COMPARTMENT 14

CLEANING / REPLACING THE ONE FIT ALL CLEANING SYSTEM 15

REMOVING / INSTALLING THE SUCTION INLET 17

TROUBLESHOOTING 18

4

SAFETY INSTRUCTIONS

Ensure that the appliance and all of its parts and components are properly

installed, prepared, and deployed.

Before using, check if the power voltage of your Aztech VC3000

corresponds correctly to your home’s power supply.

If the Aztech VC3000 would not be used for a long period, remove the

batteries of the vacuum cleaner and its components and store it in a cool

dry place.

To extend the battery life of the appliance, for its rst use or reuse (after

a long period of rest), charge the vacuum cleaner’s battery for at least

16 hours. The Aztech VC3000’s battery would be able to reach optimal

performance after 2 to 3 times of full charging and discharging.

If not in use, ensure to unplug your appliance’s power adapter.

Do not place the appliance in hot places or in places commonly exposed

to multiple sources of heat such as refrigerators.

Do not use wet hands in operating the appliance and in inserting or

removing its power adapter to prevent electrical shocks. We suggest that

you thoroughly dry your hands rst before utilizing the Aztech VC3000.

Always check if the Docking Station is properly connected to the power

outlet before use.

Switch OFF the vacuum cleaner before doing any cleaning, relocation, or

appliance maintenance.

When unplugging the Docking Station’s power adapter, do not pull or tug

its cord. Hold the power adapter properly on its base when unplugging it

from the power outlet. Also, ensure that the power cord is kept away from

heat and or sharp edges that could cause external damage to the cord.

Do not use the appliance if the power cord is damaged. Always use the

dedicated power cord included in the product package.

This appliance is strictly intended for household (indoor) use only.

Commercial spaces may expose the device to over usage and or other

external factors (e.g. number of people, excessive variety of dirt) which

may cause damage to the appliance.

Should damages be found in the appliance, please do not use the

appliance and immediately bring it to the Aztech Service Center for repair

or replacement.

Do not use the appliance on small and highly elevated spaces (e.g.

Bedside tables, chairs) where its movement is extremely limited. This may

expose the appliance to damages.

The Smart Robotic Vacuum Cleaner is not intended for use by persons

with reduced physical, sensory or mental capabilities, and or lack of

experience or knowledge. Constant supervision should be provided

to these individuals in using, cleaning, operating the appliance or by a

person responsible for their safety.

•

5

PACKAGE CONTENTS

VC3000 Docking Station Power Adapter Virtual Wall

Trailing Bar Cleaning Brush (2) Side Brush

Suction InletHEPA Filter (2) Mops

Remote Control

APPLIANCE OVERVIEW

Bumper

Dust

Cover

Exhaust

Inlet

Charging

Signal

Receiver

LED Display

Area

Touch

Buttons/

Indicators

Bumper

Bar

Sensor

Window

DC

Charging

Interface

Power

Switch

TOP VIEW

6

Battery

Compartment

Left Wheel

Lifting

Bracket

Roller Brush

Left Side

Brush

Charging

Electrodes

Lifting

Trailing

Bar

UV Lamp

Cliff Sensor

Universal

Wheel

Right Side

Brush

Right Wheel

Digital

Display

Schedule

Indicator

UV Mode

Indicator

SPOT

Dark

Cleaning

Mode

Indicator

Garbage

Indicator

DOCK

AUTO

Current Time Display. Displays the current time (in 24-

hour format) of the day.

•

CURRENT TIME DISPLAY

DAY DISPLAY

CHARGING

Day Display. Displays the current Day set on the device

(e.g. 1 stands for Monday, 2 stands for Tuesday)

•

Charging Status Display.

Displays (1) a series of 1s to indicate that the

appliance is currently charging, and

Displays (2) FULL to indicate that the appliance has

already nished charging.

•

»

FULLY CHARGED

DIGITAL DISPLAY

BOTTOM VIEW

CONTROL PANEL BUTTONS AND DISPLAY

7

AUTO. Press this button and the vacuum cleaner will start

automatic cleaning. During this mode, once the vacuum

cleaner’s battery becomes low, the vacuum cleaner will

automatically return to its Docking Station.

•

SPOT. Press this button and the vacuum cleaner will enter

SPOT cleaning mode. During this mode, the vacuum

cleaner enters a 1m2 range and will start cleaning this

area in an expanding spiral mode for 2 to 3 minutes.

•

NOTE: Touch any button on the vacuum cleaner’s control

panel to stop its cleaning operation.

Error Code Display. Displays different error codes

(provided in the TROUBLESHOOTING section of this

user manual) which corresponds to the current error(s)

encountered by the appliance.

•

ERROR DISPLAY

SCHEDULE INDICATOR. Indicates that you can now enter

the preferred cleaning schedule(s) using the Remote

Control. This LED automatically turns ON upon pressing

the button on the Remote Control.

•

UV MODE INDICATOR. Indicates that the vacuum cleaner’s

UV lamp is currently ENABLED or DISABLED By default, the

UV lamp feature is enabled, and the UV icon is ON.

•

GARBAGE INDICATOR. Turns ON to indicate any of the

following:

The suction inlet of the vacuum cleaner is blocked by

dust

The dustbin has reached full capacity

The dirt sensor is covered by dust

•

»

DARK CLEANING MODE INDICATOR. Indicates that the

vacuum cleaner has entered Dark Cleaning mode. This

LED automatically turns ON upon pressing the button

on the Remote Control.

•

DOCK. Press this button and the vacuum cleaner will

automatically locate its Docking Station to charge.

•

CLEANING MODE INDICATORS

VACUUM CLEANER BUTTONS

8

Correctly insert two (2) AAA batteries in the

Remote Control’s battery compartment

while observing the correct polarity.

•

In using the Remote Control, ensure that

you are 4 meters near the vacuum cleaner

and that the Remote Control is properly

aimed at the vacuum cleaner’s sensor.

•

NOTE: Incorrect battery installation may

damage the Remote Control and or cause

unexpected operation failures.

**OBSERVE POLARITY

4 METERS

** Aim the Remote Control at

the vacuum cleaner’s sensor

TIPS IN USING THE REMOTE CONTROL

DOCK. Press this button and the vacuum cleaner

will automatically proceed to its Docking Station

to charge.

•

UV. Press this button and the vacuum cleaner will

turn the UV lamp ON or OFF.

•

MUTE. Press this button and the vacuum cleaner

will enter mute cleaning mode.

•

SPOT. Press this button and the cleaner will enter

spiral cleaning mode.

•

POWER. Press this button and the cleaner will enter

sleep mode.

•

TIME. Press this button to enter time/schedule

cleaning mode.

•

NOTE: Press and hold this button for ten (10)

seconds to wake up the vacuum cleaner.

DARK. Press this button and the vacuum cleaner

will enter dark area cleaning mode.

•

AUTO. Press this button and the vacuum cleaner

will enter automatic cleaning mode.

•

Arrow Buttons. Press any of these buttons and the

cleaner will correspond to the direction of the

button pressed.

•

OK. Press this button to conrm entered settings.

You may also press this button to enter blocker

following cleaning mode.

•

REMOTE CONTROL BUTTONS

9

Correctly insert two (2) AA batteries in the

Virtual Wall’s battery compartment as

indicated on the image below.

•

Both Side and Front IR Window’s control range

is up to 4 meters. The distance, however, is

affected by the environment and current

battery power.

•

NOTE: Incorrect battery installation may

damage the Virtual Wall and or cause

unexpected operation failures.

The Virtual Wall is highly suggested to be

placed in doorways and or before stairs to

limit the vacuum cleaner’s movement.

•

TIPS IN USING THE VIRTUAL WALL

**OBSERVE

CORRECT BATTERY

POLARITY

Always make sure that the Front and Side IR Windows are free from any blockage

and or obstructions that may hinder its functionality.

The Virtual Wall should at least be 50cm away from the vacuum cleaner’s

Docking Station to avoid any interference.

•

(3)

Front &

Side IR

(0)

Power

(1)

Front IR

(2)

Side IR

Side

Switch

Side

Indicator

Side IR

Window

Front IR

Window

Front

Indicator

SIDE SWITCH IS ON POSITION

(0). The Virtual Wall is switched

OFF.

•

SIDE SWITCH IS ON POSITION

(1). Only the Virtual wall’s Front

IR Window would be ON.

•

SIDE SWITCH IS ON POSITION

(2). Only the Virtual wall’s Side

IR Window would be ON.

•

SIDE SWITCH IS ON POSITION (3).

Both Front and Side IR Windows

would be ON

•

NOTE: Battery duration would

largely depend on how long it

will be used and the number of

IR windows enabled. ENSURE to

turn OFF the Virtual Wall when

not in use.

VIRTUAL WALL

10

In charging the Aztech VC3000, ensure to

switch it ON rst before placing it correctly

to its Docking Station.

•

Ensure that there are no obstacles and or

uneven surfaces 2 meters in front of the and

0.5 meters on both sides of the Docking

Station.

•

TIPS IN USING THE DOCKING STATION

Ensure that the IR emission window is free of

any blockage. This may hinder the vacuum

cleaner in locating the Docking Station

whenever charging automatically

•

Always keep the Docking Station’s power

cord neatly arranged. You may use the

allotted wire storage located behind the

Docking Station to arrange it accordingly.

•

USING THE AZTECH VC3000

TIPS BEFORE USING YOUR VACUUM CLEANER

Before use, ensure that the appliance and all of its parts and components are

properly installed (and deployed).

Before using, check if the power voltage of your vacuum cleaner corresponds

to your home’s power supply.

To hasten its cleaning procedure, remove any object which may hinder your

vacuum cleaner’s cleaning operation (e.g. Glass bottles, fabrics, wiring).

•

DOCKING STATION

11

STEP 1

Position the Docking Station on a smooth and

stable ground and plug the Docking Station’s

power adapter to its power outlet. You may

then switch ON the Aztech VC3000 and lodge

it into the Docking Station to begin charging the

vacuum cleaner.

Ensure to do the following:

For rst use/reuse (after a long period of rest),

charge the vacuum cleaner’s battery for at

least 16 hours. Do take note that you have to

SWITCH ON the Aztech VC3000 for it to start

charging.

Keep the Docking Station’s wiring tidily kept

and arranged in its wiring compartment

found on its back.

Both the Docking Station’s front (2 meters)

and sides (0.5 meters) should be free from

obstacles and or blockages which may

hinder the vacuum cleaner in locating and or

lodging into the Docking Station.

•

STEP 2

Correctly insert the needed batteries of the

Remote Control (2 x AAA) and the Virtual Wall

(2 x AA) and position the Virtual Wall on the

preferred location where you want to limit the

vacuum cleaner’s movement.

STEP 3

On the Aztech VC3000 or on its Remote

Control, press the AUTO button to begin

automatic cleaning. The Aztech VC3000 would

automatically return to its Docking Station to

charge itself once it runs out of batteries.

**OBSERVE BATTERY POLARITY

CONTROL

PANEL REMOTE

CONTROL

12

SETTING THE TIME

Press the button to start entering the

current day and time.

1.

Press the or button to shift between

hour and minute.

1.

Press the or button to shift between

Monday to Sunday.

2.

Press the button to select the day

and it will be highlighted. If you wish to

cancel, select the button and the

selected DAY will ash.

3.

Press the OK button to select current day

and to begin entering the current hour

and minute.

4.

Press the or to increase or decrease

the time value.

2.

Press the OK or button to save the

current hour and minute setting and the

vacuum cleaner will automatically enter

standby mode.

3.

SELECT CANCEL

SETTING THE CURRENT DAY

SETTING THE CURRENT TIME

SHIFT

DAYS

SHIFT

HOUR &

MINUTE

INCREASE DECREASE

13

Press the button, then press the

button to start entering the cleaning

schedule.

1.

Press the or button to shift between

hour and minute.

1.

Press the or button to shift between

Monday to Sunday.

2.

Press the button to select the day and

it will be highlighted. If you wish to cancel

day selection, select the button and

the DAY will ash.

3.

Press the OK button to select current

day and to begin entering the current

hour and minute.

4.

Press the or to increase or decrease

the time value.

2.

Press the OK button to save the cleaning

schedule and the vacuum cleaner will

automatically enter standby mode.

3.

Press the button to save the current

hour and week setting and press the

button to automatically enter standby

mode.

4.

SELECT CANCEL

INCREASE DECREASE

SETTING THE CLEANING SCHEDULE

SETTING THE DAY SCHEDULE

SETTING THE TIME SCHEDULE

SHIFT

DAYS

SHIFT

HOUR &

MINUTE

14

CARE AND MAINTENANCE

On the vacuum cleaner, loosen the

battery compartment’s screws using

a screwdriver and lift the battery

compartment lid.

1.

Unbuckle the vacuum cleaner’s battery

and replace the vacuum cleaner’s

battery as needed by locking into place

the buckle of the vacuum cleaner with

the new battery correctly.

2.

NOTE: Only use genuine Aztech VC3000

battery replacements in replacing your

Aztech VC3000’s battery.

TIPS IN SAVING BATTERY LIFE

When not in use, place the vacuum cleaner in its charging state to

constantly keep the vacuum cleaner’s battery in its optimal state.

If the vacuum cleaner would not be used for a long period of time,

ensure to regularly charge the cleaner once a month to constantly

keep the vacuum cleaner’s battery in its optimal state.

•

Press the PUSH button on the dust cover

to open the dust cover.

1.

Properly secure into place the battery

inside the battery compartment.

3.

Fasten the battery compartment lid

screws as required.

4.

LOOSEN

UNBUCKLE

SECURE INTO PLACE

FASTEN

PUSH DUST

COVER

REPLACING / INSTALLING THE

VC3000’S BATTERY

CLEANING THE DUSTBIN COMPARTMENT

15

Carefully take out the dust bin from the

vacuum cleaner.

2.

Dislodge the dustbin compartment

cover’s buckle and remove dirt and

other rubbish contents as required.

3.

You may remove the 3D and the HEPA

lter from the dust bin compartment, and

wash each component separately with

water.

4.

Dry each component properly. You

may use a hair dryer’s cool air setting

to properly dry each part. You may

then Reassemble the dustbin and its

components as required and reinstall

the dustbin compartment to the vacuum

cleaner.

5.

Using your index ngers, unlock the U

shaped buckle on both sides of the

cleaning bracket to remove the cleaning

bracket.

1.

PULL OUT

OPEN DUST

BIN

3D FILTER HEPA

RETURN AND

LOCK

UNLOCK

BUCKLES

CLEANING / REPLACING THE ONE FIT ALL

CLEANING SYSTEM

16

You may strip out the ONE FIT ALL brush

from the roller for deeper cleaning or

component replacement.

5.

NOTE: In replacing the ONE FIT ALL brush,

ensure to ONLY use genuine Aztech

products.

Install the right side of the roller brush into

the vacuum cleaner’s drive shaft. The

semi-circular hole of the roller brush must

align to the semi-circle gure of the drive

shaft. You may have to rotate the roller

brush to align these.

6.

Ensure that the roller brush is properly

lodged in and installed. The soft semi-

circular rubber cap of the brush must be

atly positioned on the vacuum cleaner.

7.

Align the buckles of the cleaning bracket

to the two (2) U-shaped grooves on the

surface of the vacuum cleaner and press

down to lock.

8.

Remove the brush’ tube xing member

and rubber cap on both sides of the

roller brush and remove the hair knotted

around the brush tube xing member.

4.

Pull up the left side of the brush and slowly

lift out the roller brush to completely

remove the component from the

vacuum cleaner.

2.

You may wash the brush with water as

needed. Ensure to completely dry the

cleaning component afterwards.

3.

PULL OUT BRUSH

WASH AND DRY

THE BRUSH

REMOVE AND

CLEAN BRUSH

FIX

STRIP ONE FIT

ALL BRUSH

OPTION:

INSTALL ROLLER

BRUSH

LOCK PROPERLY

INTO PLACE

ALIGN CLEANING

BRACKET BUCKLES

17

Using the cleaning brush, dislodge the

cleaning bracket from the rack by inserting

the cleaning brush into the two gaps of

the cleaning bracket and gently turning it

to separate the two components.

3.

Install the suction inlet buckle to the two

rubber columns of the bracket and press

down the suction inlet until it rmly locks

into place.

4.

Lodge the Aztech VC3000 to its Docking

Station, press the AUTO button on the

remote or on the vacuum cleaner, and

you may now start using the suction

function.

5.

Pull up the left side of the brush and slowly

lift out the roller brush to completely

remove the component from the vacuum

cleaner.

2.

Using your index ngers, unlock the U

shaped buckle on both sides of the

cleaning bracket to remove the cleaning

bracket.

1.

The Aztech VC3000 provides the Suction option as an alternative method in cleaning

areas with excessive fur or pet hair, which would often get stuck on the vacuum

cleaner’s default brush setting. With the suction option, you will save more time when it

comes to brush cleaning.

UNLOCK

BUCKLES

PULL OUT BRUSH

DISLODGE

BRACKET

INSTALL

SUCTION INLET

INSTALL

SUCTION INLET

REMOVING / INSTALLING THE SUCTION INLET

18

During use, there would be cases wherein the Aztech VC3000 would stop working

and would be sending an alarm sound followed by a digital display of the error it

encountered.

TROUBLESHOOTING

FAULT

CODE FAILURE CAUSE SOLUTION

E001 Ground Sensor

failure

The sensor tip is blocked

or the cleaner is stuck

by stairs

Gently clean the ground sensor or

carefully lift the vacuum cleaner

manually.

E002

Suction inlet is

blocked or the

dustbin is full

Garbage sensor tip is

dusty and or the suction

is blocked.

Clear the dirt on the sensor tip and

suction inlet.

E003 Left or right

wheel failure

Lines or wiring got

tangled in either the left

or right wheel.

Gently clean the ground sensor or

carefully lift the vacuum cleaner

manually to untangle cables or wiring.

E004

Left or right

side brush

failure

Cables or wiring got

tangled in either the left

or right side brush.

Gently clean the ground sensor or

carefully lift the vacuum cleaner

manually to untangle cables or wiring.

E005 Left or right

wheel lifted up

Left or right wheel

lifted up

Position the vacuum cleaner on a

smooth and stable ground.

E006 Roller brush

failure

Lines or wiring got

tangled on the roller

brush.

Clear or remove the tangled lines or

wiring.

E007 Dust cover

failure

The dust cover is open or

is not tightly secured.

Properly close the dust cover of the

vacuum cleaner tightly.

E008 Dustbin Failure

The dust bin

compartment is

improperly positioned

Reinstall the dustbin compartment and

ensure that it is properly locked into

place.

E009 Battery is low The vacuum cleaner’s

battery ran out of power

Place the vacuum cleaner back to its

Docking Station to charge the vacuum

E010

The vacuum

cleaner does

not charge

The vacuum cleaner is

turned OFF or the battery

is improperly installed

Turn ON the vacuum cleaner. The

vacuum cleaner can only charge

once ON.

Reinstall the batteries.

•

E011 Sensor or

blocker failure Sensor is blocked Clean the transparent part of the

vacuum cleaner’s bumper

Aztech VC3000 User manual

Aztech VC3000 User manual

Related papers

Other documents