aivituvin AIR 21 User manual

Brand
aivituvin
Model
AIR 21
Type
User manual
INSTRUCTION
MANUAL
AIR 21
www.aivituvin.com
X
Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
Do not use this item in a way inconsistent with the
manufacturer’ s instructions as this could void the product
warranty.
01
TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
45MIN. ASSEMBLY
HARDWARE
10PCS+1 spare
P1 P2
P3 P4
P5
02
M3.5x40mm SCREW
M3.0x16mm SCREW
P6
4PCS+1 spare
M3.5x50mm SCREW
2PCS
P7
25PCS+1 spare
Latch
2PCS
Plastic botton
1PC
Plastic pipe
1PC
PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
A B C
DEF
G
1PC
1PC 1PC
03
HI
1PC 1PC
1PC
1PC
1PC
1PC Right panel
Front panel Back panel Left panel
Wooden roof
Wire roof Metal lamp tube
Divider
Tray
PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
J K
1PC
04
1PC
Metal lamp tube Metal lamp tube
PRODUCT ASSEMBLY
01
02
05
Attach C , D , E to the front panel A by 5xP2 screws.
A
P2 X5
C
D
E
Attach C , D , E to the back panel B by 5xP2 screws.
Ensure all corners line up before screwing together.
B
Put in the “H” from the bottom.
Screw “H” to the house from the bottom up by 4xP1 screws.
P2 X5
H
P1 X4
PRODUCT ASSEMBLY
03
04
06
Screw F, G to the house at the hinges by 8xP3 screws.
Ensure F and G are line up before screwing.
P3 X8
G
F
Complete the roof by screwing the latch P4 by 8xP3 screws.
P3 X8
P4 X2
PRODUCT ASSEMBLY
05
07
I
J
K
P6X1
P3X2
P7X1
P3X3
Finish here for only buying one tortoise house
Rota the metal lamp holder firstly.
Screw it to the cage using the P6 by 2xP3 on the upper part ; then
screw the lower part using P7 by 3xP3.
PRODUCT ASSEMBLY
06
07
08
Take out the side panel Part E from the other tortoise house.
Pls ignore the following for only one tortoise house owner!
The below steps are the assembly for the 2nd tortoise house
if you buying 2 houses.
Take out the side panel Part C from one of the tortoise house.
Take off the lamp holder and assemble it on the right side.
C
E
PRODUCT ASSEMBLY
08
09
Screw the connect pieces P5 by 4xP3 screws.
P5
X4
P3
X8
Repeat on the other side.
WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury,property
damage or loss,whether direct,indirect,or incidental,resulting from the incorrect
attachment,improper use,inadequate miantenance,or neglect of this product.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

aivituvin AIR 21 User manual

Brand
aivituvin
Model
AIR 21
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents