Yamaha DV-S5450 User manual

Brand: Yamaha

Model: DV-S5450

Type: User manual

This manual is also suitable for

DVD-S520

DVD-S520/DV-S5450

SERVICE MANUAL

DVD PLAYER

DVD-S520/DV-S5450

100795

■CONTENTS

TO SERVICE PERSONNEL .......................................... 1

WARNINGS ................................................................ 1~2

PREVENTION OF ELECTRO STATIC DISCHARGE.............

LOCALE MANAGEMENT INFORMATION ................... 3

FRONT PANELS............................................................ 4

REMOTE CONTROL TRANSMITTER .......................... 4

REAR PANELS .......................................................... 5~6

SPECIFICATIONS...................................................... 6~7

DISASSEMBLY PROCEDURES ................................... 8

SERVICE POSITION...................................................... 9

SERVICE HINTS ............................................................ 9

DIAGNOSTIC SOFTWARE: SCRIPT INTERFACES

.... 10~11

INTERACTIVE TESTS ........................................... 12~18

TEST INSTRUCTIONS .......................................... 18~21

TROUBLESHOOTING ........................................... 22~28

TECHNICAL SPECIFICATIONS DVD MODULE

...... 29~30

LIST OF ABBREVIATIONS ......................................... 31

IC DESCRIPTIONS ................................................ 32~41

WIRING DIAGRAM ...................................................... 42

BLOCK DIAGRAM................................................. 43~44

PRINTED CIRCUIT BOARD .................................. 45~65

SCHEMATIC DIAGRAM ........................................ 65~77

PARTS LIST........................................................... 78~87

REMOTE CONTROL TRANSMITTER ........................ 88

IMPORTANT NOTICE

This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.

It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already

known and understood by the users, and have therefore not been restated.

WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal

injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons,

we advise all YAMAHA product owners that any service required should be performed by an authorized

YAMAHA Retailer or the appointed service representative.

IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or

recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.

The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and

service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable

and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please

contact the distributor's Service Division.

WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have

accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).

IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.

P.O.Box 1, Hamamatsu, Japan

DVD-S520/DV-S5450

WALL

OUTLET EQUIPMENT

UNDER TEST

AC LEAKAGE

TESTER OR

EQUIVALENT

INSULATING

TABLE

■WARNINGS

WARNING: CHEMICAL CONTENT NOTICE!

The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and /or plastic

(where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency

(and possibly other entities) to cause cancer and/or birth defects or other reproductive harm.

DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA-

SON WHATSOEVER!

Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose

eyes to solder/flux vapor!

If you come in contact with solder or components located inside the enclosure of this product, wash your hands before

handling food.

WARNING: Laser Safety

This product contains a laser beam component. This component may emit invisible, as well as visible radiation, which may

cause eye damage. To protect your eyes and skin from laser radiation, the following precautions must be used during

servicing of the unit.

1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm away from

the laser pick-up unit at all times. Do not stare at the laser beam at any time.

2) Do not attempt to readjust, disassemble or repair the laser pick-up, unless noted elsewhere in this manual.

3) CAUTION: Use of controls, adjustments or performance of procedures other than those specified herein may result in

hazardous radiation exposure.

Laser Emitting conditions:

1) When the Top Cover is removed and the "POWER" SW is turned to the "ON" position, the laser component will emit a

beam for several seconds to detect if a disc is present. During this time (5 - 10 sec.) the laser may radiate through the lens

of the laser pick-up unit. Do not attempt any servicing during this period!

If no disc is detected, the laser will stop emitting the beam. When a disc is loaded, you will not be exposed to any laser

emissions.

2) The laser power level can be adjusted with the VR on the pick-up PWB. However, this level has been set by the factory

prior to shipping from the factory. Do not adjust this laser level control unless instruction is provided elsewhere in this

manual.

Adjustment of this control can increase the laser emission level from the device.

■TO SERVICE PERSONNEL

1. Critical Components Information

Components having special characteristics are marked s

and must be replaced with parts having specifications equal

to those originally installed.

2. Leakage Current Measurement (For 120V Models Only)

When service has been completed, it is imperative to verify

that all exposed conductive surfaces are properly insulated

from supply circuits.

●Meter impedance should be equivalent to 1500 ohm shunted

by 0.15µF.

●Leakage current must not exceed 0.5mA.

●Be sure to test for leakage with the AC plug in both polarities.

THE DVD PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE PER-

SONNEL.

DVD-S520/DV-S5450

U, C models B, G modelsR, A, T, P models

CAUTION

- Visible and invisible laser

radiation when open. Avoid exposure to beam.

DANGER

- Visible and invisible laser radiation

when open. Avoid direct exposure to beam.

CAUTION

- Visible and invisible laser

radiation when open. Avoid exposure to beam.

Laser Diode Properties

Type: Semiconductor laser GaAlAs

Wave length: 650 nm (DVD)

780 nm (VCD/CD)

Output Power: 7 mW (DVD)

10 mW (VCD/CD)

Beam divergence: 60 degree

Output value is determined by CFR CHAPTER1, SUBCHAPTER J

VARO! : AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄkymÄTTÖMÄLLE LASER-

SÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

VARNING! : OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.

BETRAKTA EJ STRÅLEN.

WARNING

The use of optical instruments with this product will increase eye hazard.

Repair handling should take place as much as possible with a disc loaded inside the player

WARNING LOCATION: REAR PANEL

CAUTION VISIBLE AND INVISIBLE LASER RADIATI ON WHEN OPEN. AVOID EXPOSURE TO BEAM

ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING UNDGÅ UDSÆTTELSE FOR STRÅLING

ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES UNNGÅ EKSPONERING FOR STRÅLEN

VARNING SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD BETRAKTA EJ STRÅLEN

VARO! AVATT AESSA OLET ALTTIINA NÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE LASER SÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN

VORSICHT SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN

DANGER VISIBLE AND INVISIBLE LASER RADIATI ON WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM

ATTENTION RAYONNEMENT LASER VISIBLE ET INVISIBLE EN CAS D'OUVERTURE EXPOSITION DANGEREUSE AU FAISCEAU

Warning for power supply

The primary side of the power supply including the heatsink carries live mains voltage when the player is

connected to the mains even when the player is switched off !

This primary area is not shielded so it is possible to touch copper tracks and/or components when servicing the player.

Service personnel have to take precautions to prevent touching this area or components in this area .

The primary side of the power supply has been indicated with a lightening stroke and a stripe-marked print on the printed

wiring board

Note:

The screws on the DVD mechanism (position 18-1 in on the exploded view drawing) may never be touched,

removed or re-adjusted.

Handle the DVD mechanism with care when the unit has to be exchanged!

The DVD mechanism is very sensitive for dropping or giving shocks.

DVD-S520/DV-S5450

■LOCALE MANAGEMENT INFORMATION

Locale Management Information : This DVD player is designed and manufactured to respond to the Locale Management

Information that is recorded on the DVD disc. If the Locale number described on the DVD disc does not correspond to the

Locale number of this DVD player, this DVD player cannot play this disc.

This product incorporates copyright protection

technology that is protected by method claims of

certain U.S. patents and other intellectual

property rights owned by Macrovision

Corporation and other rights owners. Use of this

authorized by Macrovision Corporation, and is

intended for home and other limited viewing uses

only unless otherwise authorized by Macrovision

Corporation. Reverse engineering or

disassembly is prohibited.

■PREVENTION OF ELECTRO STATIC DISCHARGE

The laser diode in the traverse unit (optical pickup) may be damaged due to static electricity from clothes or the human body.

Use caution to prevent electrostatic damage when servicing or handling the laser diode.

1. Grounding for electrostatic damage prevention

Some devices, such as the DVD player, use an optical pickup (laser diode) that will be damaged by static electricity in the

working environment. Only attempt service after ensuring that all grounding procedures have been completed.

1. Worktable grounding

Put a grounded conductive material (sheet) or iron sheet on the area where the optical pickup is placed.

2. Human body grounding

Use an anti-static wrist strap to discharge the static electricity from your body.

1M Conductive material

(sheet) or steel sheet

Anti-static wrist strip

2. Handling of the optical pickup

1. To prevent damage to the optical pickup replacement parts during transportation and before installation, both ends of the

laser diode are short-circuited. After installing the new part, remove the short circuit according to the correct procedure in

this service manual.

2. Do not use a tester to check the laser diode in the optical pickup. The power supply in the tester will damage the laser

diode.

3. Handling Precautions for the Traverse Unit (Optical Pickup)

1. Handle the traverse unit (optical pickup) gently, as it is an extremely high-precision assembly.

2. When replacing the optical pickup, install the flexible cable and cut its short land with wire cutters. See the optical pickup

replacement procedure in this service manual. Before replacing the traverse unit, remove the shorting pin for preventing

static electricity damage and install the new unit. Reconnect the connector as quickly as possible.

3. The flexible cable lines may break if an excessive force is applied to it. Use caution when handling the cable.

4. The semi-fixed resistor for laser power adjustment should not be adjusted. Do not turn the resistor.

DVD-S520/DV-S5450

■FRONT PANELS

DVD-S520

DV-S5450

■REMOTE CONTROL TRANSMITTER

DVD-S520/DV-S5450

■REAR PANELS

DVD-S520 B, G models

DVD-S520 U, C models

DVD-S520 A model

DVD-S520 R model

DVD-S520 T model

DVD-S520 P model

DVD-S520/DV-S5450

■SPECIFICATIONS

PLAYBACK SYSTEM

DVD Video

Video CD & SVCD

CD (CD Recordable and CD Rewritable)

DVD+RW

MP3

OPTICAL READOUT SYSTEM

Lasertype Semiconductor AlGaAs

Numerical Aperture 0.60 (DVD)

0.45 (VCD/CD)

Wavelength 650 nm (DVD)

780 nm (VCD/CD)

DVD DISC FORMAT

Medium Optical Disc

Diameter 12cm (8cm)

Playing time One layer 2.15 h*

(12cm) Dual layer 4 h*

Two side 4.30 h*

Single layer

Two side 8 h*

Dual layer

VIDEO FORMAT

DA Converter 10 bits

Signal handling Components

Digital Compression MPEG2 for DVD

MPEG1 for VCD

TV STANDARD (PAL/50Hz) (NTSC/60Hz)

Number of lines 625 525

Playback Multistandard (PAL/NTSC)

DVD

Horizontal Resolution 720 pixels 720 pixels

Vertical Resolution 576 lines 480 lines

VCD

Horizontal Resolution 352 pixels 352 pixels

Vertical Resolution 288 lines 240 lines

DV-S5450 U model

DV-S5450 A model

VIDEO PERFORMANCE

Video output 1 Vpp into 75 ohm

S-Video output Y: 1 Vpp into 75 ohm

C: 0.3 Vpp into 75 ohm

Component video output

Y: 1 Vpp into 75 ohm (U, C, A, R, T, P)

PB/CB PR/CR:0.7Vpp into 75 ohm

(U, C, A, R, T, P)

RGB (SCART) output 0.7 Vpp into 75 ohm (B, G)

Black Level Shift On/Off

Video Shift Left/Right

AUDIO FORMAT

Digital MPEG Compressed Digital

DTS/Dolby Digital

PCM 16, 20, 24 bits

fs, 44.1, 48, 96 kHz

Analog Sound Stereo

Dolby Pro Logic downmix from Dolby Digital multi-channel sound

3D Sound (TruSurround) for virtual 5.1 channel sound on 2 speakers

AUDIO PERFORMANCE

DA Conver ter 24 bits

DVD fs 96 kHz 2 Hz 44 kHz

fs 48 kHz 2 Hz 22 kHz

Video CD fs 44.1 kHz 2 Hz 20 kHz

CD fs 44.1 kHz 2 Hz 20 kHz

Signal-Noise (1kHz) 95 dB

Dynamic Range (1kHz) 95 dB

Harmonic Distortion and Noise (1kHz) 0.0035 %

MPEG MP3 MPEG Audio L3

CONNECTIONS

Y Output Cinch (green) (U, C, A, R, T, P)

PB/CB Output Cinch (blue) (U, C, A, R, T, P)

PR/CR Output Cinch (red) (U, C, A, R, T, P)

SCART Euroconnector (B, G)

S-Video Output Mini DIN, 4 pins

Video Output Cinch (yellow)

Audio L+R output Cinch (white/red)

Subwoofer output Cinch (black)

Digital Output 1 coaxial, 1 optical

IEC958 for CDDA / LPCM

IEC1937 for MPEG1/2, Dolby Digital and DTS

DVD-S520/DV-S5450

TruSurround and the SRS symbol are trademarks of

SRS Labs., Inc. TruSurround technology is

incorporated under license from SRS Labs., Inc.

Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of

Dolby Laboratories.

”DTS” and ”DTS Digital Surround” are trademarks of

Digital Theater Systems, Inc.

GENERAL

Dimensions(w x h x d) 435 x 91 x 314 mm

(17-1/8" x 3-5/8" x 12-9/16")

Weight Approx. 3.3 Kg (7 lbs. 4.5 oz.)

Finish DVD-S520 Black color (U, C, A, B, G, P)

Gold color (R, G, T)

Titan color (G, B)

DV-S5450 Black color (U, A)

Silver color (U)

Power supply 120 V, 60 Hz (U, C)

230 V, 50 Hz (B, G)

240 V, 50 Hz (A)

110–240 V, 50/60 Hz (R)

220 V, 50 Hz (T)

Power consumption 20 W

Standby power con- 5 W

sumption (reference data)

PACKAGE CONTENTS

DVD-Video Player, Remote Control & Batteries,

Owner's Manual, Audio/Video cable (U, C, A, R, T),

Audio cable (B, G), Video cable (B, G)

GENERAL FUNCTIONALITY

Stop / Play / Pause

Fast Forward / Backward

Time Search

Step Forward / Backward

Slow Motion

Title / Chapter / Track Select

Skip Next / Previous

Repeat (Chapter / Title / All) or (Track / All)

A-B Repeat

Shuffle

Scan

New enhanced user graphical interface

Zoom (xl.33, x2. x4) with picture enhancement

Smart Picture for convenient personal colour setting

NTSC/PAL Conversion

Screen Saver (Dim 75% after 15 min.)

3D Sound (TruSurround)

Audio and video bit rate indicator

DVD FUNCTIONALITY

Multi-angle Selection

Audio Selection (1 out of maximum 8 languages)

Subtitles Selection (1 out of maximum 32 languages)

Aspect Ratio conversion (16:9, 4:3 Letterbox, 4:3 Pan Scan)

Parental Control and Child Lock

Disc Menu support (Title Menu and Access Control)

Resume (5 discs) after stop / standby

Programming Titles/chapters with Favourite Track Selection

VIDEO CD FUNCTIONALITY

Playback Control for VCD 2.0 discs

Child Lock

Resume (5 discs) after stop / standby

Programming Tracks with Favourite Track Selection

AUDIO CD FUNCTIONALITY

Time Display (Total / Track)

Full audio functionality with remote control

Programming with Favourite Track Selection

MP3 FUNCTIONALITY

Time Display (Track)

Album and Track Selection

Repeat (Disc / Album / Track)

* typical playing time for movie with 2 spoken languages and

3 subtitle languages.

Specifications subject to change without prior notice

U ........ U.S.A. model C ........ Canada model

G ........ Europe model B ........ British model

A ........ Australia model R ........ General model

T ......... China model P ........ South America model

This product incorporates copyright protection

technology that is protected by method claims of

certain U.S. patents and other intellectual property

rights owned by Macrovision Corporation and other

rights owners. Use of this copyright protection

technology must be authorized by Macrovision

Corporation, and is intended for home and other

limited viewing uses only unless otherwise authorized

by Macrovision Corporation. Reverse engineering or

disassembly is prohibited.

DVD-S520/DV-S5450

Power supply unit 55

⇒remove connections.

⇒remove 2 screws 35

(board → frame).

⇒release snaps of 2 spacers

(board → frame).

⇒demount board.

Display board 53

⇒Remove 7 screws 36

(board → front), pay

attention to earth spring.

⇒demount board.

Front panel ass'y

⇒open tray.

⇒remove cover tray 19.

⇒remove 2 screws 35

(front panel 1 → frame).

⇒unlock front panel from

frame by releasing

successively 6 snaps ( on

the left, on the bottom and

on the right) with taking care

to avoid breaking snaps.

⇒remove 2 connectors (on

mono board and on P.S.U.).

⇒put front panel ass'y.

A/ V board 52

⇒remove flex connections to

Mono board.

⇒remove 8* screws 35, 36

* 7 screws (B, G model).

⇒release snaps of 2 spacers.

⇒demount board.

mounting

↑

↓

demounting

Top Cover 32

⇒Remove 7 screws 33.

⇒Lift cover at rear side to

remove.

Standby board

⇒Remove 2 screws 36

( board → front).

⇒demount board.

DVD MODULE

⇒Remove tray of

DVD Mechanism.

⇒Remove connections to

Mono board.

⇒remove 4 screws 35

⇒demount module.

DVD MONO Board 18-2

⇒Remove flex connections to

turntable motor and sledge

motor.

⇒remove 4 screws (mono

board 18-2 → DVD

mechanism 18-1)

⇒remove carefully flex

connection to OPU and wire

connection to tray motor.

⇒demount board.

● The way to remove tray

1. Push left end of the lever under the tray toward the right

by using screwdriver, move the tray by pulling it

forward. (Fig. 1)

Fig. 1

2.7 mm for screws with 33, 35 and 36

1.7 mm for removing MONO board (18-2) from

DVD Mechanism (18-1)

T10

■DISASSEMBLY PROCEDURES

See exploded view for item numbers.

When disassembling, use the special screw driver with tip

shape in figure.

Fig. 2

2. While lifting up the lever (1), move the left side of the

tray by pulling it forward (2). (Fig. 2)

3. While lifting up the tray (3), remove the tray by pulling it

forward (4). (Fig. 2)

DVD-S520/DV-S5450

■SERVICE HINTS

Diagnostic software

In chapter “Diagnostic software”, some tests are refering

to the SCART functionality.

These tests are for sets with RGB-output.

For sets without RGB-output, no SCART connector is

mounted.

In these sets, the SCART tests will automatically be

skipped.

■SERVICE POSITION

See figure 1 for the service position

1. Remove the cables from the cable tie housing.

2. Remove 4 screws that mount the DVD module to the

bottom frame.

3. Move the DVD module backward slightly and flip the

module over, so that the component side of the board

faces upwards, and the module is in the service

position.

Fig. 1

DVD-S520/DV-S5450

Press 2 keys simultaneously

Connect to mains.

During the test, the following display

is shown: the counter counts down

from the number of nuclei to be run

before the test finishes. Example:

SET O.K.?

YES

To exit DEALER SCRIPT, disconnect from mains.

1. DEALER SCRIPT

1.1 Purpose of Dealer Script

The dealer script can give a diagnosis on a standalone

DVD player; no other equipment is needed to perform a

number of hardware tests to check if the DVD player is

faulty. The diagnosis is simply a "error" or "pass"

message; no indication is given of faulty hardware

modules. Only tests within the scope of the diagnostic

software will be executed hence only faults within this

scope can be detected.

■DIAGNOSTIC SOFTWARE : SCRIPT INTERFACES

1.2 Contents of Dealer Script

The dealer script executes all diagnostic nuclei that do not

need any user interaction and are meaningful on a

standalone DVD player.

The nuclei called in the dealer script are the following (the

number after each nucleus name corresponds with the

number being on the local display when the nucleus is

executed during the dealer script):

Nucleus Description

VideoColSetupComm 9 Checks the I2C interface with the RGB video processor on the Audio/Video board

(only for DVD players with RGB video processor).

VideoScartSwComm 8 Checks the I2C interface with the scart switch on the Audio/Video board

PapChksFl 7 Calculate and verify checksum of FLASH memory.

PapDramWrR 6 Pattern test of all locations in the DRAM(s).

PapI2cDisp 5 Checks the I2C interface with the slave processor on the display PCB.

PapS2bEcho 4 Checks the I2C interface to the basic engine.

PapI2cNvram 3 Checks the I2C interface with the NVRAM.

PapNvramWrR 2 Pattern test of all locations in the NVRAM

CompSdramWrR 1 Pattern test of all locations in the SDRAM(s).

DVD-S520/DV-S5450

SLEDGE TEST

BeSledgeOut/In(41ab)

FOCUS TEST

BeFocusOn(38a)

DISC MOTOR TEST

BeDiscMotorOn(39a)

RADIAL TEST

BeRadialOn(40a)

JUMP TEST

BeGroovesIn/Mid/Out(42abc)

Press 2 keys simultaneously

Connect to main

To exit player test,

disconnect from mains

INTERACTIVE TESTS

DISPLAY TEST

DispDisplay(30)

LED TEST

DispLed(29)

KEYBOARD TEST

DispKeyb(27)

SCART LOOP TEST

AudioPinkNoiseOn(20a)

VideoScartSwDvd(54a)

VideoColDencOn(23a)

PICTURE TEST

DISPLAY PCB

MONO PCB(SERVO)

& BASIC ENGINE

MONO PCB

DIGITAL PART

TRAY TEST

BeTrayOut/In(43ab)

VERSION NUMBER

BeVer(37)

REMOTE CONTROL

DispRc(28)

P50 LOOP BACK TEST

DispP50(60)

TRAY TEST

BeTrayOut/In(43ab)

ERROR LOG & BITS

LogReadErr(31)

LogReadbits(32)

LOOP TEST

= Dealer script exclusive of test2

AudioSineOn(21a)

SOUND 1 TEST

SCART DVD TEST

SOUND 2 TEST

VideoScartSwPass(54b)

2. PLAYER SCRIPT

2.1 Purpose of Player Script

The Player script will give the opportunity to perform a test

that will determine which of the DVD player's modules are

faulty, to read the error log and error bits and to perform an

endurance loop test. To successfully perform the tests, the

DVD player must be connected to a TV set to check the

output of a number of nuclei. For DVDv2b a multi-channel

amplifier, a set of 6 boxes and an external video source

are necessary to test. To be able to check results of

certain nuclei, the player script expects some interaction

of the user (i.e. to approve a test picture or a test sound).

Some nuclei (e.g. nuclei that test functionality of the Basic

Engine module) require that the DVD player itself is

opened, to enable the user to observe moving parts and

approve their movement visually. Only tests within the

scope of the diagnostic software will be executed hence

only faults within this scope can be detected.

2.2 Contents of Player Script

The player script contains all nuclei that are useful on a

DVD player that is connected to a TV-set and help to

determine which module of the DVD player is faulty, as

well as to read out the contents of the error logs.

2.3 Structure of Player Script

The player script consists of a set of nuclei testing the

three hardware modules in the DVD player: the Display

PWB, the Digital PWB and the Basic Engine.

Nuclei run by the player test need some user interaction;

in the next paragraph this interaction is described. The

player test is done in two phases:

1. Interactive tests: this part of the player test depends

strongly on user interaction and input to determine

nucleus results and to progress through the full test.

Reading the error log and error bits information can be

useful to determine any errors that occurred recently

during normal operation of the DVD player.

2. The loop test will loop through the list of nuclei

indefinitely, till the NEXT key is pressed. The list of

nuclei is as follows:

• VideoColSetupComm

• VideoScartSwComm

• PapChksFlash

• PapI2cNvram

• CompSdramWrR

• PapS2bEcho

• PapI2cDisp

For DSW version 1.6 and above. the DSW version number

will be displayed on the local display. Press NEXT to

continue to the display test.

The display should look like the following:

2.4 Survey

DVD-S520/DV-S5450

1. DISPLAY PCB

1.1 DISPLAY TEST

The display test is performed by nucleus DispDisplay. By

putting a series of test patterns on the local display, the

local display is tested. To step through all different

patterns, the user must either press PLAY (pattern is ok)

or PAUSE (pattern was incorrect) to proceed to the next

pattern. The display of patterns is continued in a cyclic

manner until the user presses NEXT. If the user presses

NEXT before all display patterns are tested, the

DispDisplay nucleus will return TRUE (display test

successful).

1.2 LED TEST

The LED(s) on the DVD player is (are) tested by nucleus

DispLed. The user must check if the LED(s) is (are)

lighted; if it is, press PLAY, if it is not, press PAUSE. By

pressing NEXT the script will proceed to the next test. If

the user presses NEXT before PLAY or PAUSE, the

DispLed nucleus will return TRUE (LED test successful).

If OK, press PLAY If NOK, press PAUSE

press NEXT to continue

Figure 1

1.3 KEYBOARD TEST

The keyboard of the DVD player is tested by nucleus

DispKeyb. The user is expected to press all keys on the

local keyboard once. The code of the key pressed is

shown on the local display (1 hexadecimal digit)

immediately followed by a (hexadecimal) number

indicating how many times that key has been pressed.

Example of the local display during this test:

Figure 2

The key-codes displayed on the local display will scroll

from right to left when the display gets full, the text "tb-" will

remain on display.

key id. key

2 PREVIOUS

3 PAUSE

PLAY

STOP

OPEN/CLOSE

A POWER (B,G models)

Figure 3

If any keys are detected more than once (due to hardware

error), the key-code is displayed twice (or more), with the

second digit increased by 1.

If the user does not press all keys minimally once (in any

order), the DispKeys nucleus will return FALSE and cause

an error in the overall result of the player script.

The user can leave the keyboard test by pressing the

NEXT key on the local display of the DVD player for at

least one full second.

The result of the keyboard test is shown on local display

as follows:

Figure 4

Figure 5

Pressing NEXT on the local keyboard again will proceed

to the next text.

1.4 REMOTE CONTROL TEST

The remote control of the DVD player is tested by nucleus

DispRc. The user must press any key on the remote

control just once. The codes of the key pressed will be

shown on the local display in hexadecimal format.

Example:

Figure 6

■INTERACTIVE TESTS

DVD-S520/DV-S5450

In this example 23 is the hexidecimal code of the pressed RC

key. The user can leave the remote-control test by pressing

NEXT on the local keyboard of the DVD player. The remote

control test is successful if a code was received before the

user pressed the NEXT key; pressing the NEXT key before

pressing a key on the remote control gives an error in the

remote control test (note that the remote control test will also

fail if a key on the remote control was pressed but no code

was received). The remote control test does not check upon

the contents of the received code, that is it will not be checked

if the received code matches the key pressed. If desired, the

user can manually check this code by using a code-table for

the remote control key-codes.

RC Key id Hexadecimal code

POWER / C

RETURN/RESUME 83

BIT RATE EF

MENU 54

CURSOR UP 58

ON SCREEN 82

CURSOR LEFT 5A

OK 5C

CURSOR RIGHT 5B

PREVIOUS 21

CURSOR DOWN 21

NEXT 20

STOP 31

PLAY 2C

PAUSE 30

SUBTITLE 4B

ANGLE 85

ZOOM F7

AUDIO 4E

REPEAT 1D

A/B REPEAT 3B

SHUFFLE 1C

SCAN 2A

Figure 7

After pressing NEXT, the result of the remote control test

is displayed on the local display of the DVD player as

follows:

Figure 8

Figure 9

Pressing NEXT on the local keyboard again will proceed to

the next test.

1.5 P50 Loop-Back Test

For the P50 loop-back test, the user must first press a key

to decide if the test is to be performed.

The display will show the following message:

Figure 10

If the user presses PAUSE, the P50 test will be skipped.

If the user presses PLAY, the P50 test is performed and

the result is displayed as follows:

Test successfull:

Figure 11

Test fails:

Figure 12

Press the NEXT key to continue to the next text

2 MONO PCB DIGITAL PART

2.1 PICTURE TEST

The picture test is performed by putting a predefined

picture (colour bar) on the display (nucleus

DVD-S520/DV-S5450

VideoColDencOn) and asking the user for confirmation.

The display shows the following message:

Figure 13

By pressing PLAY, the user confirms the test; pressing

PAUSE will indicate the picture was invisible or incorrect.

Pressing NEXT will proceed to the next test

2.2 SOUND 1 & SCART DVD TEST

The first soundtest is performed by starting a pink noise

sound that needs confirmation from the user (nucleus

AudioPinkNoiseOn); the display shows the following

message very shortly:

Figure 14

This sound will only be audible from version cut3.1 of

Sti5505(item7503 on mono board) onwards. After starting

up sound 1, SCART loop-trough will be simultaneously

active during this test. SCART loop-trough will be

measured with the aid of an external video source.

When entering the SCART loop-trough, the local display

indicates:

Figure 15

On the TV screen, a colour bar (generated by nucleus

VideoColDencOn) is visual and the internally generated

pinknoise is audible. By pressing PLAY, the user confirms

the test; pressing PAUSE will indicate the sound was

inaudible or incorrect. Pressing NEXT will proceed to the

next test; if the user presses NEXT without pressing PLAY

or PAUSE first, the result of this test will be TRUE (sound

ok). By pressing the NEXT button, there will be switched

over to the external source, this must become now visible

on the TV screen (using the SCART). The local display

indicates:

Figure 16

The internally generated colour bar is still available on the

CVBS and Y/C outputs. And the pinknoise-signal is still

available on the cinch audio outputs. By pressing the

PREV button, the internal generated colour bar becomes

visual again.

The test can be left by pressing the NEXT key for more

than one second.

2.3 SOUND 2 TEST

The second soundtest is performed by producing a sine

sound (nucleus AudioSineOn). The signal can be stopped

by pressing the STOP-key. The display shows the

following message:

Figure 17

By pressing PLAY, the user confirms the test; pressing

PAUSE will indicate that something went wrong. To

proceed NEXT, press the STOP key first, press the NEXT

key second and wait five seconds.

3 BASIC ENGINE

note) Basic engine means DVD mechanism.

3.1 VERSION NUMBER

In the basic engine tests, the version number of the Basic

Engine will be shown first, as the following example:

Figure 18

By pressing the NEXT key, the Basic Engine tests are

started.

3.2 TRAY TEST

First, the tray is tested. The purpose of this test is also to

give the user the opportunity to put a disc in the tray of the

DVD player. Some tests on the Basic Engine require that a

disc (e.g. DVD MPTD test disc) is present in the player. At

the end of the Basic Engine tests, this tray test will be

repeated solely to enable the user to remove the disc in

the tray. The local display looks as follows:

Figure 19

By pressing PLAY or PAUSE, the user can toggle the

position of the tray. Note that this test will not contribute to

DVD-S520/DV-S5450

the test result of the Basic Engine. Pressing NEXT will

proceed to the next test, after the tray has been closed (by

the software) if it was open.

3.3 SLEDGE TEST(visual test)

The second Basic Engine test tests the sledge; the user

can move the sledge as many times as desired by using

PLAY (nucleus BeSledgeOut) and PAUSE (nucleus

BeSledgeIn).

Pressing NEXT on the local keyboard proceeds to the next

test.

Note that this test will not contribute to the test result of the

Basic Engine. The local display looks as follows during the

sledge test:

Figure 20

3.4 DISC MOTOR TEST(visual test)

The third Basic Engine test tests the disc motor (nucleus

BeDiscMotorOn); the local display looks as follows:

Figure 21

By pressing PLAY, the user confirms that the disc motor is

running; pressing PAUSE indicates the disc motor does

not work. Pressing NEXT proceeds to the next test, after a

reset of the disc motor (nucleus BeDiscMotorOff). If the

user presses NEXT before pressing PLAY or PAUSE, the

result of this test will be TRUE (disc motor is running).

3.5 FOCUS TEST(visual test)

The fourth Basic Engine test tests the focussing; first

focussing is turned on by calling nucleus BeFocusOn. The

display looks as follows:

Figure 22

By pressing PLAY, the user confirms that the focussing

was succesful; pressing PAUSE indicates a focussing

failure.

Pressing NEXT proceeds to the next test after a reset of

the focussing (nucleus BeFocusOff); if NEXT is pressed

before PLAY or PAUSE, the result of this test will be TRUE

(focus successful).

3.6 RADIAL TEST(visual & listening test)

The fifth Basic Engine test tests the radial functionality

(nucleus BeRadialOn); the local display looks as follows:

Figure 23

By pressing PLAY, the user confirms that the radial

function worked; pressing PAUSE indicates the function

does not work.

Pressing NEXT proceeds to the next test, after a reset of

the radial (nucleus BeRadialOff). If the user presses NEXT

before pressing PLAY or PAUSE, the result of this test will

be TRUE (radial successful).

3.7 JUMP TEST(listening test)

The sixth and last Basic Engine test tests the jumping by

calling nuclei BeGroovesIn, BeGroovesMid and

BeGroovesOut.

During this test, the local display looks as follows:

Figure 24

The user can switch between the three different types of

groove settings by pressing PLAY (forward to next

nucleus in the list In-Mid-Out) or PAUSE (backward in the

list In-Mid-Out).

This is done in a cyclic manner; note that this test will not

contribute to the test result of the Basic Engine. Pressing

NEXT proceeds to the next test, after the disc motor has

been shut off with a call to nucleus BeDiscMotorOff.

3.8 TRAY TEST

As a last action for the Basic Engine tests, the tray test is

repeated. The local display looks as follows:

Figure 25

This test is meant to give the user the opportunity to

remove the disc in the tray. The tray position can be

toggled using the PLAY and PAUSE key. The tray will be

closed (by the software, if it is open) before proceeding to

the next test when the user presses the NEXT key.

DVD-S520/DV-S5450

Error log / bits table

Read ERROR LOG Read ERROR BITS

in player script in player script

Basic engine errors Value: Value:

Command to the Basic Engine not allowed in this state or unknown command 150101 8

Parameter(s) from the command to the Basic Engine is not valid 150102 7

Sledge could not be moved to the inner home position 150103 6

Focus failure 150104 5

Turntable motor speed could not be reached within timeout 150105 4

Radial servo could not get on track on the disc 150106 3

PLL could not lock in the accessing or tracking state 150107 2

Subcode or sector information could not be read 150108 1

requested subcode could not be found 150109 16

Tray could not be closed or opened completely 15010A 15

TOC could not be read within timeout 15010B 14

The requested seek on the disc could not be executed 15010C 13

A requested lead-in is not on the disc 15010D 12

A non existing burst cutting area is requested 15010E 11

S2b communication error 1501F0 10

S2b communication error 1501F1 9

S2b communication error 1501F3 24

S2b communication error 1501F4 23

S2b communication error 1501F5 22

Digital PWB errors

Communication error with the Sti 5505 90000 32

Communication error with the Sti 5505 90001 31

Disply processor errors

Communication error with the display processor 190000 40

3.9 ERROR LOG

Reading the error log and error bits information can be

useful to determine any errors that occurred recently

during normal operation of the DVD player. Reading the

error log is done by nucleus LogReadErr. The display

during the errorlog readout looks as follows :

Figure 26

By pressing PLAY or PAUSE, the user can move forward

or backward (respectively) through the logged error

codes. The highlighted number indicates which errorcode

is currently on display (in the example above, errorcode

number 4 is displayed). If "0000" is displayed at all

positions, the error log is empty. Display of the logged

errors is done in a cyclic manner.

The errorcode with the lowest highlighted number is the

most recent. By pressing NEXT on the local keyboard, the

user can proceed to the next test.

3.10 ERROR BITS

Reading the error bits is done by nucleus LogReadBits.

The display during the errorbits readout looks as follows:

Figure 27

Only the set errorbits will be shown by their (decimal)

number.

Refer to the appropriate documentation for the

explanation of each bit number. If the display only shows

"EB-0", no error bits were set. By pressing NEXT, the user

can continue to the next test.

See table below:

DVD-S520/DV-S5450

ERROR CODES LOOP TEST

ERROR CODE NUCLEUS NUMBER ERROR DESCRIPTION

0601

6 Calculated checksum of FLASH is not correct

0901

9 The DVD DRAM is faulty

1104

11 I2C bus busy before start

1102

NVRAM access time-out

1103

No NVRAM Acknowledge

1104

NVRAM reply time-out

1201

12 I2C bus busy

1202

I2C bus not working

1203

Slave controller not responding

1204

Slave response is not correct

1301

13 Parity error from basic engine to serial

1302

Parity error from serial to basic engine

1303

No communication between serial and basic engine

1304

Communication time-out error

1601

16 The SDRAM is faulty

5201

5202

Error sending I2C command to COLOR SETUP IC

Error sending I2C command to SCART SWITCH IC

Colour setup IC not responding

Colour setup IC response is not correct

SCART Switch is not responding

SCART Switch response is not correct

5203

5204

5401

5402

5403

I2C bus busy

4. LOOP TEST

At the start of the loop test, the display will show the result

of the interactive player test:

Figure 28

The left side of the display contains a 3-digit code, which

can have a value between 000 and 111. These values are

to be interpreted as follows:

Displayed

Value Indication for each module

Basic Engine Mono

PCB Display

PCB

000 ok ok ok

001 ok ok faulty

010 ok faulty ok

011 ok faulty faulty

100 faulty ok ok

101 faulty ok faulty

110 faulty faulty ok

111 faulty faulty faulty

Figure 29

The loop test will perform the same nuclei as the dealer

test, but it will loop through the list of nuclei indefinitely.

The display of the DVD player will display not only the

three digits indicating correct/faulty modules and the last

found error code (as mentioned, faults are detected as far

as they can be within the scope of the diagnostic

software), but also a loop counter indicating how many

times the loop has been gone through.

Example:

FAULTY

MODULE(S)

LOOP

COUNTER NUCLEUS ERROR

Figure 30

The number after the hyphen indicates the number of

times the loop test has been performed; the 4 digits at the

right side of the display show the last error that was found

when running the loop test: the leftmost two digits of this

code indicate which nucleus resulted in a fault; the

rightmost two digits refer to the faultcode within that

nucleus. For further explanation of this error code, see list

of error codes below.

Figure 31

DVD-S520/DV-S5450

5. Servicing DVD module and MONO board

5.1 Reset of Virgin Mode

After the player has been powered up for test by the

dealer, it would have gone through the Virgin Mode. It is

possible to reset the settings made during that mode

before the delivery of player to the customer. This can be

done as shown in the following diagram:

DISCONNECT FROM MAINS

PRESS 2 KEYS

SIMULTANEOUSLY

<NEXT> + <OPEN/CLOSE> (ver 4.14a)

<PLAY> + <OPEN/CLOSE> (other version)

CONNECT TO MAINS

VIRGIN MODE IS RESET

TV SCREEN SHOWS

VIRGIN MODE MENU

Figure 32

5.2 Trade Mode

When the player is in Trade Mode, the player cannot be

controlled by means of the front key buttons, but only by

means of the remote control.

DISCONNECT FROM MAINS

IF TRADE MODE OFF

PRESS 2 KEYS

SIMULTANEOUSLY

CONNECT TO MAINS

DISCONNECT FROM MAINS

IF TRADE MODE ON

PLAYER IS IN NORMAL MODE

WHEN PRESSING FRONT

KEYS, THE PLAYER WILL

RESPOND

PRESS 2 KEYS

SIMULTANEOUSLY

CONNECT TO MAINS

PLAYER IS IN TRADE MODE

WHEN PRESSING FRONT

KEYS, THE PLAYER

DOESN'T RESPOND

Figure 33

■TEST INSTRUCTIONS

1 AV Board

These test instructions can be used for all versions of the

AV board which has the following outputs:

•Audio L/R

•5.1 Audio output

•Subwoofer output

•Optical / Coaxial digital output

•CVBS

• Y/G_vid,U/B_vid,V/R_vid output

•S-video

• Scart output

1.1 General

• All the waveforms measurement carried out in these

test instruction will be base on the testpoint indicated in

the AV board schematic diagram in the Service manual.

• Impedance of the measuring-equipment should be >

1MΩ

• Most of the tests can be done using either the

Diagnostic software “ Player script” which can be found

in the chapter “Diagnostic Software description and

troubleshooting” or the Menu interface using the

Service PC with a terminal emulation program ( e.g.

Window Hyperterminal ) where it is possible to control

the execution of the Diagnostic Nuclei

• Setup for the measurement will be done in set level

with all modules connected as shown in the Wiring

Block diagram.

1.2 General Start-Up Measurement

Supply Check:

Before starting the measurement,ensure that all power

supply are connected to the AV board.

Pin nbr

1010-9

1010-10

1010-11

Supply

-5V ( -Vcc )

+5V

The supply currents can be measured using a Tektronics

AM503B current probe or equivalent.

Supply

+5VA

+5Vvid

-5V

Power consumption ( AVG )

+5V ± 3% I = 200mA

-5V ± 3% I = 200mA

Clock Check

Ensure the present of the clock to the DAC

Clock Name

PCM_CLK Testpoint

TP10 Frequency

11.2896MHz ± 0.02% tolerance

Audio Mute Check

Measure the Audio mute voltage input at pin 12 of

connector 1010

Status

AudioMuteOn

AudioMuteOff

Value

4.7V ± 10%

-8V ± 10%

DVD-S520/DV-S5450

Check the video outputs at the following testpoints:

Name

B_VID

G_VID

R_VID

CVBS out

S-Video-C out

S-Video-Y out

Y out

U out

V out

Testpoint

TP1

TP2

TP3

TP14

TP15

TP16

TP17

TP18

TP19

All waveforms can be refer to the waveform diagram in the

chapter “Diagnostic Software description and

troubleshooting”.

1.5 Play And 16/9 Detection

Check DC voltage at S-Video-chroma output (pin 4) with a

6K8 ohm load and Scart connector (pin 8) and change the

0/6/12 input (1010-8) using the following commands:

Ref.#

25a

25b

25c

Command

Name

VideoScartLo

VideoScartMi

VideoScartHi

Remarks

Sends out 0V

±0.5V

Sends out 6V

±10%

Sends out 12V

±10%

Chroma output

<0.1V

2.0V ± 10% with

load

5.0V ± 10%

without load

<0.1V

1.6 Kill Circuit

To check the functionality of the Kill circuitry,the audio

outputs has to be present by the following command:

Ref.#

21a

Command

Name

AudioPinkNoise

Remarks

Audio Pinknoise

Audio output

Pink Noise on 6

channels

Check the audio outputs at the audio cinch of the AV board

:PinkNoise

Activate the Kill circuit by using the following command:

Ref.#

19a Command Name

AudioMuteOn Remarks

Audio Mute On

Check the audio outputs at the audio cinch of the AV board

: No waveform

Switch off the kill circuit by using the following command:

Ref.#

19b Command Name

AudioMuteOff Remarks

Audio Mute Off

Check the audio outputs at the audio cinch of the AV board

:PinkNoise

To toggle between ON and OFF,use the following

commands:

Ref.#

19a

19b

Command

Name

AudioMuteOn

AudioMuteOff

Remarks

Audio Mute On

Audio Mute Off

1.3 Audio DAC And Amplifier

Ensure that the Audio mute signal is OFF

To check the DAC and buffer amplifier,send the following

commands:

Ref.#

21a

----

20a

20b

Command

Name

AudioSineOn

Press stop

button

AudioPinkNoise

Off

Remarks

Audio Sine

signal ON

Audio Sine

signal OFF

Audio

Pinknoise ON

Audio

Pinknoise OFF

Audio output

Sine,1Khz on

stereo

No waveform

Pink Noise on

6 channels

No waveform

The audio signal ( sine or pink noise ) will also be present

on the digital output ( SPDIF ).This can be checked by

connecting digital signal to an amplifier with digital input.

Check the I2S and audio signal at the following testpoints:

Name

LRCLK

SCLK

PCM_CLK

PCM_OUT0

PCM_OUT1

PCM_OUT2

SPDIF

Front L/R out-Audio cinch

H/P L/R out

Analog out -Audio cinch

Testpoint

TP8

TP9

P10

TP7

TP27

TP28

TP11

TP13

TP20

TP25

All waveforms can be refer to the waveform diagram in the

chapter “Diagnostic software description and

troubleshooting”.

1.4 Video Output And Buffer Amplifier

Check DC output-level at all video cinch output : 1.0V DC

10% Generate a color bar using the following software

commands:

Ref.#

23a

61a

61b

23b

Command Name

VideoColDencOn

VideoColOutRGB

VideoColOutYUV

VideoColDencOff

Remarks

Colour DENC ON

RGB Colourbar

YUV Colourbar

Colourbar DENC OFF

Page is loading ...

Yamaha DV-S5450 User manual

Brand: Yamaha

Model: DV-S5450

Type: User manual

This manual is also suitable for

DVD-S520

Download PDF

report

Yamaha DV-S5450 User manual

This manual is also suitable for

Yamaha DV-S5450 User manual

Related papers

Other documents